Answer: The new volume is 95.45 mL.
Explanation:
Given: [tex]V_{1}[/tex] = 45.0 mL, [tex]P_{1}[/tex] = 0.98 atm
[tex]P_{2}[/tex] = 2.1 atm, [tex]V_{2}[/tex] = ?
According to Boyle's law, at constant temperature the pressure of a gas is inversely proportional to its volume.
Therefore, formula used to calculate the new volume is as follows.
[tex]\frac{P_{1}}{V_{1}} = \frac{P_{2}}{V_{2}}[/tex]
Substitute the values into above formula as follows.
[tex]\frac{P_{1}}{V_{1}} = \frac{P_{2}}{V_{2}}\\\frac{0.98 atm}{45.0 mL} = \frac{2.1 atm}{V_{2}}\\V_{2} = 95.45 mL[/tex]
Thus, we can conclude that the new volume is 95.45 mL.
NO LINKS OR FILES
Using Ohm's Law and Watt's Law. write the formula to find each measurement
Wattage (Watts)
Resistance (Ohms)
Voltage (Volts)
and/or
Current (Amps)
and/or
Explanation:
Mathematically, Ohm's law is given by :
V = IR
Where
V is voltage
I is current
R is resistance
The electric power of an electrical appliance is given by:
P = VI
Wattage = VI
Resistance, [tex]R=\dfrac{V}{I}[/tex]
Current, [tex]I=\dfrac{V}{R}[/tex]
Hence, this is the required solution.
A 25.0mL solution of KOH is neutralized with 30.3 mL of 0.100M HBr. What is the concentration of the original KOH solution?
Answer:
The concentration of the original KOH solution is 0.1212 M.
Explanation:
Dilution is the process to reduce the concentration of solute in solution. This is accomplished by adding more solvent to the same amount of solute. In other words, dilution is the procedure followed to prepare a less concentrated solution from a more concentrated one, and it simply consists of adding solvent to an existing solution.
As only solvent is being added, the consequence is that by not increasing the amount of solute, but if the amount of solvent, the concentration of the solute decreases.
The expression for the dilution calculation is:
Ci* Vi = Cf* Vf
where:
Ci: initial concentration Vi: initial volume Cf: final concentration Vf: final volumeIn this case:
Ci= ? Vi: 25 mL Cf: 0.1 M Vf: 30.3 mLReplacing:
Ci* 25 mL= 0.1 M* 30.3 mL
Solving:
[tex]Ci=\frac{0.1 M*30.3 mL}{25 mL}[/tex]
Ci=0.1212 M
The concentration of the original KOH solution is 0.1212 M.
Potassium hydroxide is partially soluble as shown by the
following reaction:
KOH(s) K+ (aq) + OH(aq)
What is the poH of a 3.32 x 10-5 M KOH solution?
pOH =
Your answer should be rounded to three significant figures. Do not Include
units in your answer.
Answer: 4.48 or 4.47
17 moles of oxygen is equals to how many grams
17 × ( 2 × 16 ) = 17 × 32 = 544 grams
___________________________
PLEASEEEE HELP THIS IS SCIENCE
IGNORE THE QUESTIONS WHERE I ANSWERED, I GUESSED
Answer:
where is the answer??
Please do not just take the points without answering the question.
why would an electric vehicle be allowed to travel in the high occupancy vehicles lands with only one driver ?
Answer:
because it could self drive
Explanation:
idrk but thats my answer
(hurry pls)Carl plugs in a lamp that has 0.67 of resistance and 8.1 volts running through it. What is the amount of current running through the lamp? C 543 A C 0.08 A C 12.09 A C743 A
Answer:
C)12.09 Ampere
Explanation:
V= IR
Where I= current of the system
R= resistance= 0.67 ohm
V= potential difference=8.1 volts
Substitute the values
8.1= I× 0.67
I= 8.1/0.67
=12.09 Ampere
This unbalanced equation represents a chemical reaction:
Pb(NO3)2 + Nal NaNO3 + PbI2
What is the coefficient for Nal once the equation is balanced?
Α. 1
B. 2
C. 3
D. 4
Answer:
2
Explanation:
Pb(NO3)2 + 2NaI 2NaNO3 + PbI2
To see the coefficients of NaI in the given reaction we need to balance the reaction first. The coefficient for Nal once the equation is balanced is 2. the correct option is option B.
What is balanced equation?Balanced equation is the one where the number of atoms of each species is same on reactant and product side. In balanced equation mass can neither be created nor be destroyed.
The unbalanced equation is
[tex]\rm Pb(NO_{3})_{2}+ Nal\rightarrow NaNO_{3} + PbI_{2}[/tex]
The atoms of Pb on reactant and product side is 1 so Pb is balanced.
The atoms of N is 2 on reactant and 1 on product side so balance it as
[tex]\rm Pb(NO_{3})_{2}+ Nal\rightarrow 2 NaNO_{3} + PbI_{2}[/tex]
The atoms of O is 6 on reactant and 6 on product side so it is balanced
The atoms of I is 1 on reactant and 2 on product side so balance it as
[tex]\rm Pb(NO_{3})_{2}+2 Nal\rightarrow 2NaNO_{3} + PbI_{2}[/tex]
The atoms of Na on reactant and product side is 2 so Na is balanced.
Now all the elements are balanced
Therefore, the coefficient for Nal once the equation is balanced is 2. the correct option is option B.
Learn more about the balanced equations, here:
https://brainly.com/question/7181548
#SPJ2
(10 POINTS!!!!!!!!!!!
What environmental change will take place when harmful substances get into the food and water supply of animals or plants?
A Climate change
B Increased predators
C Lack of food
D Pollution
need asap
Answer:
A climate change
Explanation:
the surrounding area would be effected in all ways imaginable, such as change in air, soil, water, plants, animals. and if you eat those said animals those harmful things can transfur into you
Four satellites are in orbit around the Earth. The heights of their four orbits
are identical. The masses of the four satellites are given in the table. For
which satellite is the gravitational pull of Earth the strongest?
can anyone tell me the answer
Answer:
A. A as concentration decreases.
Explanation:
A represents a reactant and B is a product, the concentration of the latter increases at the expense of the concentration of the former. Hence, A is the reactant of the chemical reaction as its concentration decreases.
An 18.7 g sample of platinum metal increases in temperature from 21.2C to 23.5C
when 5.7 J of heat are added. What is the specific heat of platinum?
Answer:
132.53 J/kg.°C
Explanation:
Applying,
Q = cm(t₂-t₁)................ Equation 1
Where Q = amount of heat, c = specific heat capacity of platinum metal, m = mass of platinum metal, t₁ = initial temperature, t₂ = Final temperature.
Make c the subeject of the equation
c = Q/m(t₂-t₁).............. Equation 2
From the question,
Given: Q = 5.7 J. m = 18.7 g = 0.0187 kg, t₁ = 21.2°C, t₂ = 23.5°C
Substitute these values into equation 2
c = 5.7/[0.0187×(23.5-21.2)]
c = 5.7/0.04301
c = 132.53 J/kg.°C
3. If a gas has a pressure of 32.1 psi at a temperature of 25°C, then what is the new pressure if the temperature is increased to 75°C?
Answer:
P2 = 37.5 psi
Explanation:
P1 = 32.1 psi
T1 = 25°C + 273 = 298K
T2 = 75°C + 273 = 348K
P2 = ?
P1/T1 = P2/T2
or
P2 = (T2/T1)P1
= (348K/298K)(32.1 psi)
= 37.5 psi
Use the given Nernst equation and reaction to solve this problem. What is the potential of this cell with the given conditions?
2Li (aq) + F2(g) 2Li+(aq) + 2F- (aq)
E° = +5.92 volts
T = 200°C
[Li+] = 10.0 molar
[F-] = 10.0 molar
Answer:
The 2nd one is the one
Explanation:
and it isn't writen out all the way
What were some of the causes of the Amu Darya and Syr Darya rivers being ruined?
urban sewer drainage
tannery dumping
tourism
drying up
agricultural chemicals
Answer:
drying up
agricultural chemicals
Explanation:
1. If 80.0 ml of 3.00 M HCl is used to make a 100. ml of dilute acid, what is the molarity
of new dilute HCl solution?
We are given:
M1 = 3 Molar V1 = 80 mL
M2 = x Molar V2 = 100 mL
Finding the molarity:
We know that:
M₁V₁ = M₂V₂
where V can be in any units
(3)(80) = (x)(100)
x = 240/100 [dividing both sides by 100]
x = 2.4 Molar
Calculate the new temperature when a container of
gas has a pressure of 795 mm Hg at 273 K and the
pressure is lowered to 358 mm Hg.
(Gay Lussac's Law) P1T2/P2T1
- 0.00165
- 246
- 123
- 606
Answer: The new temperature of container is 123 K.
Explanation:
Given: [tex]P_{1}[/tex] = 795 mm Hg, [tex]T_{1}[/tex] = 273 K
[tex]P_{2}[/tex] = 358 mm Hg, [tex]T_{2}[/tex] = ?
Formula used to calculate the new temperature is as follows.
[tex]\frac{P_{1}}{T_{1}} = \frac{P_{2}}{T_{2}}[/tex]
Substitute the values into above formula as follows.
[tex]\frac{P_{1}}{T_{1}} = \frac{P_{2}}{T_{2}}\\\frac{795 mm Hg}{273 K} = \frac{358 mm Hg}{T_{2}}\\T_{2} = 123 K[/tex]
Thus, we can conclude that the new temperature of container is 123 K.
List and describe the four layers of the Earth.
Answer:
Crust- thinest layer; the part we live on
Mantle- just beneath the crust; consists of magma
Outer Core- liquid metal; super hot; thickest layer (i think)
Inner Core- solid metal; SUPER compressed; hottest layer
moles of H2O are needed to exactly react with 2.0 moles of Ca
Answer:
4
Explanation:
so first write the balance equation
Ca+2H2O---->Ca(OH)2 + H2
then use molar ratio of H2O and Ca
which is 2:1 so if there are 2 moles of ca there will be 4 moles as you times it by 2. like this
Ca:H2O
1:2
2:4
Hope this helps u understand:)
1. True or False: Fungi are reproduced through the spread of spores.
O True
O False
Answer:
True
Explanation:
Fungi reproduce by spawning absurd amount of spores greatly increasing the survival rate of the fungi.
Answer:
true
Explanation:
How many energy levels does an atom of carbon have?
Answer:
6
Explanation:
- How much power does it take to lift a
1,000 N load 10 m in 20 s?
Answer:
"500 Joule/sec" is the right answer.
Explanation:
The given values are:
Force,
F = 1000 N
Velocity,
s = 10 m
Time,
t = 20 s
Now,
The power will be:
= [tex]\frac{Force\times Velocity}{Time}[/tex]
On putting the values, we get
= [tex]\frac{1000\times 10}{20}[/tex]
= [tex]\frac{10000}{20}[/tex]
= [tex]500 \ Joule/sec[/tex]
A student wants to determine if a
sample of tap water contains Mg+2.
Which of the following pieces of
information are not needed to do a
titration ?
Answer:
The Density of Magnesium.
Explanation:
Find the hydroxide concentration of a LiOH soultion that has a pOH of 8.65.
[OH] = _____ (round to 2 decimal places)
Answer: i need help
Explanation:
A solvent has a freezing point of 10°C. What is the most likely freezing point if 5 grams of Salt is mixed with the solvent? (AKS 5e)
Question 5 options:
15°C
20°C
5°C
10°C
[tex]\huge{\color{hotpink}{Hola}}[/tex]
if an atom has 4 protons, 5 neutrons, and 4 electrons, what would its atomic mass be?
Answer:
4
Explanation:
If I remember correctly, the atomic # will always be the same as the # of electrons
The H3O+ ion concentration of a solution is 1 × 10–5 mole per liter. This solution is
A. acidic and has a pH of 5
B. acidic and has a pH of 9
C. basic and has a pH of 5
D. basic and has a pH of 9
The given [tex]H_3O^+[/tex] ion concentration of a solution is an acidic solution and has a pH of 5.
How does the pH scale measure?The letters pH stand for the potential of hydrogen since pH is effectively a measure of the concentration of hydrogen ions (that is, protons) in a substance.The pH scale measures the relative acidity and alkalinity of solutions.It's a negative logarithmic scale of base ten that measures the potential of a solution to accept protons in the form of hydrogen ions.A pH scale ranges from 0 to 14 with 7 being neutral. A pH lower than 7 is considered acidic and a pH greater than 7 is considered basic (alkaline).What is the pH value of an [tex]H_3O^+[/tex] ion?pH can be calculated by using the following equation:
pH = -1(log[H3O+])
Where [H3O+] is the concentration of hydronium ions (hydrogen ions).
The concentration is given as 1 × [tex]10^-^5[/tex] mole per liter.
So, if [H3O+] = 1x[tex]10^-^5[/tex] mol/L,
then the pH = -1(log(1 × [tex]10^-^5[/tex] )) = 5
So, the pH of the given solution is 5. The value is less than 7. Hence it is considered an acidic solution.
Therefore, The given solution is an acidic solution with a pH of 5.
Learn more about the pH of a solution here:
https://brainly.com/question/4137247
#SPJ2
What is the number of moles in 10.62 L of H2S gas at STP?
Answer:
0.474 moles
Explanation:
divide 10.62 by 22.4.
What are the two limitations of earth plates
Answer:
The tectonic style and viability of modern plate tectonics in the early Earth is still debated. Field observations and theoretical arguments both in favor and against the uniformitarian view of plate tectonics back until the Archean continue to accumulate. Here, we present the first numerical modeling results that address for a hotter Earth the viability of subduction, one of the main requirements for plate tectonics. A hotter mantle has mainly two effects: 1) viscosity is lower, and 2) more melt is produced, which in a plate tectonic setting will lead to a thicker oceanic crust and harzburgite layer. Although compositional buoyancy resulting from these thick crust and harzburgite might be a serious limitation for subduction initiation, our modeling results show that eclogitization significantly relaxes this limitation for a developed, ongoing subduction process. Furthermore, the lower viscosity leads to more frequent slab breakoff, and sometimes to crustal separation from the mantle lithosphere. Unlike earlier propositions, not compositional buoyancy considerations, but this lithospheric weakness could be the principle limitation to the viability of plate tectonics in a hotter Earth. These results suggest a new explanation for the absence of ultrahigh-pressure metamorphism (UHPM) and blueschists in most of the Precambrian: early slabs were not too buoyant, but too weak to provide a mechanism for UHPM and exhumation.
Explanation:
Which pair of elements will form an ionic bond?
a. Potassium and Oxygen
b. Iron and Barium
C. Sulfur and Nitrogen
d. Calcium and Silicon
I believe that the answer is A.
The combination of potassium (K) and oxygen (O2) produces K2O (potassium oxide). The balanced equation is 2K + O2 ==> K2O.