A rocket at rest on the ground with initial mass 20,000 kg, 80% of which is fuel, burns 200kg/s as it flies
directly upwards. The exhaust gas exits the rocket at a relative speed of 1.80 km/s. Find (a) the thrust of
the rocket, (b) how long it takes to exhaust its fuel, and (c) the rocket’s speed at the end of its engine burn.
Assume g is constant and neglect air resistance.

The diameter of the copper wire must be 2.76 mm to have its resistance is to be the same as that of an equal length of aluminium wire with diameter 3.48 mm.

Any straight line section that cuts through the middle of a circle and has ends that are on the circle is considered a circle's diameter in geometry. It is also known as the circle's longest chord. The diameter of a spherical can be defined using either of the two meanings.

In more recent usage, the term "diameter" also refers to the measure d of a circle. Since all diameters of a circle or sphere have the same length, which is equal to twice the radius, one refers to the diameter in this context rather than the diameter (which pertains to the line section itself).

Learn more about  diameter

https://brainly.com/question/5501950

#SPJ1

Full Question: What Diameter Must A Copper Wire Have If Its Resistance Is To Be The Same As That Of An Equal Length Of Aluminum Wire With Diameter 3.48 Mm ?D = ____________ Mm please Show Steps And Reasoning.

What diameter must a copper wire have if its resistance is to be the same as that of an equal length of aluminum wire with diameter 3.48 mm ?

d = ____________ mm

Answer: D. Most of her initial energy has been converted back to gravitational potential energy. As she falls, her gravitational potential energy is converted into kinetic energy. As she bounces back up, the kinetic energy is converted back into gravitational potential energy, and the process continues until she eventually comes to a stop. Some energy may be lost due to air resistance and friction, but the majority of the energy is conserved and converted back and forth between kinetic and potential forms.

Answer:Star B Star B gives off more red light

Explanation:

To determine the exact age of a layer of rock, geologists typically use radiometric dating techniques such as measuring the decay of radioactive isotopes in rocks.

While fossils found within a layer of rock can provide important clues about the age of the rock, they cannot determine the exact age of the layer with precision.

This is because the fossil record is incomplete and fossils found in a layer of rock are unlikely to represent all species that existed during a particular time period.

Learn more about the age of a rock:https://brainly.com/question/29770777

#SPJ1

Therefore, the tension in the section of rope that connects the pulleys is 45.3 N.

Force is a physical quantity that describes the interaction between two objects or systems. It is defined as the push or pull on an object that results from the interaction with another object or system. Force can cause an object to accelerate, deform, or change direction. It is typically measured in units of newtons (N) in the International System of Units (SI). The direction of a force is described by its vector properties, which include magnitude, direction, and point of application.

Here,

a) To find the speed of the block after it travels a distance of 1.6 m, we can use conservation of energy. The potential energy at the beginning is all converted to kinetic energy at the end:

(1/2)(m)(v²) = (m)(g)(h)

where "v" is the speed of the block at the end, "g" is the acceleration due to gravity, and "h" is the height the block falls. Since the block falls a distance of 1.6 m, we can substitute:

(1/2)(m)(v²) = (m)(g)(1.6)

Solving for "v", we get:

v = √(3.2g)

Plugging in the value for acceleration due to gravity, we get:

v = √(3.2 x 9.8) = 5.02 m/s

Therefore, the speed of the block after it travels a distance of 1.6 m is 5.02 m/s.

b) The constant acceleration of the block can also be found using conservation of energy. The potential energy at the beginning is converted to kinetic energy at the end, so:

(1/2)(m)(v²) = (m)(g)(h)

Solving for "g", we get:

g = (v²) / (2h)

Plugging in the values for "v" and "h", we get:

g = (5.02²) / (2 x 1.6) = 7.89 m/s²

Therefore, the constant acceleration of the block is 7.89 m/s².

c) To find the tension in the section of rope that connects the pulleys, we can use Newton's second law of motion. The net force on the system is equal to the mass times the acceleration:

(2m)(a) = T

where "T" is the tension in the section of rope that connects the pulleys. We can also use the fact that the tension is the same throughout the rope, so the tension in the upper and lower sections of the rope are also "T". Then, the net force on each pulley is:

(T - mg) = ma

where "a" is the acceleration of the system (which we found to be 7.89 m/s^2 in part b). Substituting "T = 2ma + mg" from the first equation into the second equation, we get:

(2ma + mg - mg) = m

Simplifying, we get:

T = 3ma

Plugging in the values for "m" and "a", we get:

T = 3(2.4 kg)(7.89 m/s²) = 45.3 N

To know more about force,

https://brainly.com/question/29044739

#SPJ9

1. Start by searching in academic databases such as Scholar and JSTOR for journal articles on this topic. Look for relevant keywords such as "diversity," "workforce," "hiring," and "non-business activities."

Diversity is the presence of different types of people and ideas in any given community, organization, or setting. It can be seen in the way people are different in terms of race, ethnicity, disability, language, socio-economic background, religious beliefs, and other personal characteristics. Diversity is essential for a healthy, and successful society, as it encourages the exchange of ideas, encourages creativity and innovation, and understanding.

To learn more about diversity

https://brainly.com/question/26794205

#SPJ1

The new reading on the spring scale is 2mg/3. In the static configuration, the tension in the rope is equal to the weight of the two blocks, since they are not accelerating.

When the bottom block becomes detached, the remaining block will accelerate downwards due to the force of gravity. The pulley will also start to rotate, and the direction of the tension in the rope will change.

Let a be the acceleration of the remaining block, and let alpha be the angular acceleration of the pulley. Since the rope does not slide across the surface of the pulley, the acceleration of the two blocks must be the same. Therefore,

a = alpha * R

[tex]T * R = (1/2)MR^2 * \alpha[/tex]

where T is the tension in the rope.

Since the acceleration of the remaining block is downwards, the tension in the rope must be less than the weight of the block. Therefore,

T - mg = ma

Substituting the expression for a from the equation above, we get

[tex]T - mg = \alpha * R[/tex]

Substituting the expression for alpha from the torque equation above, we get

[tex]T - mg = (T * R) / (2 * R^2 / M)[/tex]

Simplifying, we get

T = 2mg / 3

To know more about tension visit:-

brainly.com/question/29763438

#SPJ1

Answer:

Without knowing the actual distances involved, it's difficult to give a specific answer. However, we can use the information given in the question to determine the distance between points A and C using the Pythagorean theorem.

Let's assume that the boy walked a distance of x units from point A to point B, and a distance of y units from point B to point C. Then we can use the following diagram:

           C

           |

y           |

|           |   x

|-----------B

           |

           |

           A

According to the problem, the boy first walked a certain distance x in a direction that is not specified (we only know that it's forward and north). Then he turned 136 degrees to his right and walked a distance y to reach point C. Since the turn was to the right, the boy turned towards the east, so we can draw a line from point B towards the right to represent this change in direction.

Now we can apply the Pythagorean theorem to find the distance between points A and C:

AC² = AB² + BC²

We know that AB = x, and we need to find BC. To do so, we can use trigonometry. Since the boy turned 136 degrees to his right, he ended up facing 180 - 136 = 44 degrees east of north. This means that the angle between BC and AB is 90 - 44 = 46 degrees.

Using trigonometry, we can express BC in terms of y and the tangent of the angle 46 degrees:

tan(46) = BC / y

BC = y tan(46)

Substituting this expression for BC into the Pythagorean theorem equation, we get:

AC² = x² + (y tan(46))²

Simplifying:

AC² = x² + y² tan²(46)

We can calculate tan²(46) using a calculator or a table of trigonometric functions. Let's assume that tan²(46) is equal to 1.470. Then we have:

AC² = x² + 1.470y²

To find the distance between A and C, we need to take the square root of both sides of the equation:

AC = sqrt(x² + 1.470y²)

Without more information about the distances involved, we cannot compute the actual numerical value of AC.

Answer:

yes

Explanation:

A rare fraction is the area of a sound wave where the particles are less dense because it's moving through the air made of alternating areas of higher and lower density

The Procedure and Data section provides evidence that magnetic fields exist by demonstrating the force exerted by a magnetic field on a nearby object. In this experiment, two magnets are used, and one magnet is taped down on a smooth.

A magnet is an object that produces a magnetic field, which is a force that can attract or repel certain materials, such as iron, nickel, and cobalt. Magnets have two poles, called the north pole and the south pole, which are opposite in nature and attract each other, while like poles repel each other. This property of magnets is used in various applications, such as electric motors, generators, magnetic storage devices, and compasses. Magnets can be either natural, such as lodestone, or artificial, such as magnets made from iron, nickel, cobalt, or other magnetic materials.

To know more about magnet visit :

https://brainly.com/question/2841288

#SPJ1

When water is used to generate electricity in hydropower facilities, it is either stored in dams or is moving through rivers.

In a man-made lake, called reservoir, behind it, a traditional dam stores water. When the dam is breached, the water rotates a turbine that is coupled to an electricity-generating generator. On the dam's downstream side, the water trickles back into the river.

Hydropower is a renewable energy source since it depends on the sun-driven water cycle. A pure source of energy, hydropower is powered by water.

To know more about Hydroelectric visit:

https://brainly.com/question/15228003

#SPJ9

In light of this, the combined two-cart system will move at the same speed as the launch cart before to the accident, or v0.

The cumulative momentum of the two carts after the collision must match the incoming momentum (vector sums, use proper signs). With the formula p = mrivri = mrfvrf + mbfvbf, you should be able to determine the missing velocity since you already know the mass, velocity, and one of the two cars' speeds.

The conservation of momentum, which is represented by the following:

m1v1 + m2v2 = (m1 + m2)vf

where the two carts' initial velocities are v1 and v2, their masses are m1 and m2, and their final velocity is vf following a collision.

Given that the two carts in this instance have the same mass, we can reduce the equation to read as follows:

2m*v0 = (2m)*vf

where m represents each cart's mass.

Solving for vf, we get:

vf = v0

To know more about speed visit:-

https://brainly.com/question/28224010

#SPJ1

Answer:

Explanation:

Introduction:

As the world shifts towards renewable energy sources, the use of wind power is becoming increasingly popular. Wind power harnesses the power of the wind to generate electricity, and it has proven to be a reliable, cost-effective, and environmentally-friendly source of energy. In this report, we will discuss the benefits of wind power and how it can be used in our community.

Benefits of Wind Power:

Wind power has numerous benefits, including:

Clean and Environmentally-Friendly: Wind power generates electricity without producing harmful greenhouse gas emissions, air pollution, or toxic waste. It is a clean and sustainable energy source that helps reduce our carbon footprint and combat climate change.

Cost-Effective: Wind power is one of the most cost-effective renewable energy sources available today. Once a wind turbine is installed, the ongoing operating costs are relatively low, and the energy produced is essentially free.

Energy Security: Wind power provides energy security and independence. It reduces our dependence on foreign oil and other fossil fuels, which can be affected by geopolitical conflicts, price fluctuations, and supply disruptions.

Job Creation: Wind power creates jobs in the construction, maintenance, and manufacturing sectors. The growth of the wind power industry can provide economic benefits to our community and the country as a whole.

How Wind Power Works:

Wind power works by harnessing the kinetic energy of the wind and converting it into electrical energy. Wind turbines consist of a rotor, blades, a nacelle, and a tower. As the wind blows, it causes the rotor to spin, which in turn spins the blades. The blades are designed to capture the wind's energy and convert it into rotational energy. The rotational energy is then transferred to a generator in the nacelle, which converts it into electrical energy. The electricity is sent to a transformer, which increases the voltage and sends it to the power grid for distribution.

Using Wind Power in Our Community:

Our community has several options for using wind power, including:

Small-Scale Wind Turbines: Small-scale wind turbines can be installed on residential or commercial properties. They can generate enough electricity to power a home or business, and any excess energy can be sent back to the grid.

Large-Scale Wind Farms: Large-scale wind farms can be installed in rural areas, where there is ample wind and space. These wind farms can generate large amounts of electricity and provide energy to the grid, which can be distributed to our community.

Conclusion:

Wind power is a reliable, cost-effective, and environmentally-friendly source of energy that can provide numerous benefits to our community. By investing in wind power, we can reduce our carbon footprint, create jobs, and secure our energy future. It is a smart investment that will pay off for years to come.

Answer:

The tension force in the string at the bottom of the circle is approximately 1.85 N.

Explanation:

To solve this problem, we can use the principle of centripetal force, which states that the force required to keep an object moving in a circle is equal to the product of its mass, its velocity squared, and the radius of the circle, divided by the distance from the center of the circle to the object. At the top and bottom of the circle, the tension force in the string will be different due to the influence of gravity.

First, we can find the gravitational force acting on the ball. The weight of the ball can be calculated as:

Fg = mg

where m is the mass of the ball, and g is the acceleration due to gravity.

Substituting the given values, we get:

Fg = (0.04 kg) * (9.81 m/s^2) = 0.3924 N

At the top of the circle, the tension force in the string will be less than the weight of the ball, because gravity is pulling the ball away from the center of the circle, reducing the force required to keep it moving in a circle. Therefore, the tension force can be calculated as:

Ttop = Fg - (m * v^2 / r)

where Ttop is the tension force at the top of the circle, m is the mass of the ball, v is the tangential velocity of the ball, and r is the radius of the circle.

Substituting the given values, we get:

Ttop = 0.3924 N - (0.04 kg * (2 m/s)^2 / 0.22 m) = 0.3924 N - 1.4545 N = -1.0621 N

The negative sign indicates that the tension force is directed upwards, opposite to the direction of the ball's motion. This tension force is not strong enough to keep the ball moving in a circle at the top of the circle, so the ball will lose contact with the string.

At the bottom of the circle, the tension force in the string will be greater than the weight of the ball, because gravity is pulling the ball towards the center of the circle, increasing the force required to keep it moving in a circle. Therefore, the tension force can be calculated as:

Tbottom = Fg + (m * v^2 / r)

where Tbottom is the tension force at the bottom of the circle.

Substituting the given values, we get:

Tbottom = 0.3924 N + (0.04 kg * (2 m/s)^2 / 0.22 m) = 0.3924 N + 1.4545 N = 1.8469 N

Therefore, the tension force in the string at the bottom of the circle is approximately 1.85 N.

3.89 km/s is the rocket's final engine burn speed.

The rocket equation can be used to determine the rocket's thrust:

Thrust is calculated as follows: (final mass flow rate minus initial mass flow rate) x (exhaust gas mass flow rate x exhaust gas velocity)

The initial mass flow rate is 16,000 kg/s (0.8 x 20,000 kg).

The final mass flow rate is equal to 20,000 kg - 200 kg/s x t, where t is the engine's burn period.

We obtain the following by substituting the values in the question:

Thrust equals 360,000 N when calculated as (200 kg/s x 1.8 km/s + (20,000 kg - 200 kg/s x t - 16,000 kg) x 1.8 km/s)

20,000 kg - 200 kg/s x t = 0.2 x 20,000 kg

t = 20 seconds.

(c) The rocket equation can be used to determine the rocket's speed at the conclusion of its engine burn:

V is equal to (exhaust velocity) x ln[(initial mass)/(final mass)].

The rocket's final mass, which is what remains after all of its fuel has been consumed, is as follows:

final mass = (mass of rocket) - (mass of fuel)

final mass = 20,000 kg - 16,000 kg

final mass = 4,000 kg

Δv = 1.80 km/s x ln[(20,000 kg) / (4,000 kg)]

Δv = 1.80 km/s x ln(5)

Δv = 3.89 km/s

to know more about relative speed here;

brainly.com/question/14362959

#SPJ1

The reaction is an equal and opposite force applied by the road on the car's wheels in the direction of the car's motion.

What is Unbalanced Force?

Unbalanced force refers to a situation where the net force acting on an object is not zero, which causes the object to accelerate in a particular direction. When two or more forces act on an object and the net force is not equal to zero, the forces are said to be unbalanced.

Explanation of unbalanced forces: When the driver hits the brakes, the car's wheels apply a frictional force on the road in the opposite direction of the car's motion. This force is greater than the force that was previously keeping the car moving at a constant speed, and as a result, the net force on the car is in the opposite direction of its motion. This unbalanced force causes the car to slow down and eventually come to a stop.

Learn more about Unbalanced Force from given link

https://brainly.com/question/227461

#SPJ1

Answer:

It takes approximately 0.625 seconds for the person to be stopped by the airbag.

Explanation:

We can use the formula for average acceleration to solve this problem:

a = (v_f - v_i) / t

where:

a = average acceleration

v_f = final velocity (0 m/s)

v_i = initial velocity (15 m/s)

t = time

We know that the airbag provides a stopping force of 1200 N, which is equal to the net force on the person-car system. We can use Newton's second law of motion to find the acceleration of the person:

F_net = ma

where:

F_net = net force (1200 N)

m = mass of person (50 kg)

a = acceleration

Solving for a, we get:

a = F_net / m

a = 1200 N / 50 kg

a = 24 m/s^2

Now we can substitute the values of a, v_f, and v_i into the formula for average acceleration and solve for t:

a = (v_f - v_i) / t

24 m/s^2 = (0 m/s - 15 m/s) / t

t = -15 m/s / 24 m/s^2

t = 0.625 s

Therefore, it takes approximately 0.625 seconds for the person to be stopped by the airbag.

For v0 less than Vmin, there is no value of h that allows both balls to hit the ground at the same time.

To solve for the time it takes for the second ball to hit the ground, we can use the equation for free-fall motion:

h = 1/2 gt^2

Where h is the height of the building and g is the acceleration due to gravity (9.81 m/s^2).

Plugging in the given values, we get:

45.0 m = 1/2 (9.81 m/s^2) t^2

Solving for t, we get:

t = sqrt(9.18 s^2)

t ≈ 3.03 s

Therefore, the second ball will hit the ground after approximately 3.03 seconds.

Let's denote the initial velocity of the first ball as v0, the time it takes to reach the ground as t1, and the height of the building as h. For the second ball, the time it takes to reach the ground is t2 = t1 - 1.14 s.

Using the kinematic equation for free-fall motion, we can relate the height h and time t1 for the first ball:

h = (1/2)gt1^2 + v0t1

Similarly, for the second ball:

h = (1/2)gt2^2

Substituting t2 = t1 - 1.14 s, we get:

h = (1/2)g(t1 - 1.14)^2

For the two balls to hit the ground at the same time, the heights must be equal, so:

(1/2)gt1^2 + v0t1 = (1/2)g(t1 - 1.14)^2

Simplifying and rearranging, we get:

Vmin = 1.14sqrt(g)

Learn more about "initial velocity" here:

https://brainly.com/question/9365999

#SPJ1

The mechanical advantage for the given question is 6, as the mechanical advantage of a wheel and axle is equal to the radius of the wheel divided by the radius of the axle.

The ratio of the force generated by a simple machine to the force applied to it is known as mechanical advantage. By only comparing the radius of the wheel to the radius of the axle and applying the formula Ma=Rw/Ra to the situation of the wheel and axle, the mechanical advantage can be determined.

The ratio of the wheel's radius to the axle's radius is what gives the wheel and axle their mechanical advantage.

To learn more about mechanical advantage visit:

brainly.com/question/16617083

#SPJ1

The entire distance that an object travels in a given amount of time is the definition of average speed for that object. Therefore, her average speed for the entire trip was 1.49 m/s.

What is the average speed of entire trip?

It is calculated by dividing the total distance something travels by the total amount of time it spends traveling.

average speed = total distance / total time

Now, let's find the total time. The time it takes to go from A to B is:

time = distance / speed = d / 2.3

The time it takes to go from B to A is:

time = distance / speed = d / 1.1

total time = d / 2.3 + d / 1.1

total time = (d * 1.1 + d * 2.3) / (2.3 * 1.1)

total time = (3.4d) / 2.53

Now, we can find the average speed:

average speed = 2d / [(3.4d) / 2.53]

average speed = (2 * 2.53) / 3.4

average sped = 1.49 m/s (rounded to two decimal places).

To know more about average speed visit:-

https://brainly.com/question/12322912

#SPJ1

The coefficient of kinetic friction between the block and the surface is 0.5.

The coefficient of kinetic friction is a measure of the resistance between two objects that are in contact with each other and moving relative to each other. It is denoted by the symbol "μk" and is defined as the ratio of the force of kinetic friction between two objects and the normal force acting between them.

Here the block was initially at rest and after travelling some distance it came to rest, therefore change in kinetic energy ∆K=0

Therefore mgh = unghcotx - umgx = 0

where h = 1m, x = 1m

u= 1 / 1+1

= 0.5

Learn more about friction on

https://brainly.com/question/24338873

#SPJ1

The pressure applied by the man to the ground is 551812.5 Pa or 5.06 psi.

Force applied per unit area is what is referred to as pressure. It can be calculated mathematically using P=FA, where F is the force acting perpendicular to surface area A. The pascal (Pa), or one newton per square metre (N/m 2), is the common unit of pressure.

The following formula can be used to determine how much pressure the man is exerting on the ground:

Pressure = Force / Area

where Area is the portion of the stilts that are in touch with the ground and Force is the man's weight.

Weight equals mass multiplied by gravitational acceleration yields the man's weight.

Weight = 90 kg * 9.81 m/s²

Weight = 882.9 N

The area of each stilt is:

Area = length * width

Area = 0.04 m * 0.04 m

Area = 0.0016 m²

As a result, the man is exerting the following pressure on the ground:

Pressure = Force / Area

Pressure = 882.9 N / 0.0016 m²

Pressure = 551812.5 Pa

To know more about pressure visit:-

https://brainly.com/question/13046888

#SPJ1

The distance travelled by the plane in 27 seconds, given that the acceleration of the plane is 7.00 ft/s/, is 2551.5 ft

The distance travelled by the plane in 27 seconds can be obtained as illustrated below:

s = ut + 1/2at²  

s = (0 × 27) + (1/2 × 7 × 27²)

s =  0 + (3.5 × 729)

s  = 0 + 2551.5

s = 2551.5 ft

From the calculation made above, we can conclude that the distance travelled  is 2551.5 ft

Learn more about distance travelled:

https://brainly.com/question/18265275

#SPJ1

The tοtal energy οf the system is 0.0181 J.  The velοcity at the amplitude can be fοund using the fοrmula fοr simple harmοnic mοtiοn.

Energy plays a crucial rοle in virtually every aspect οf οur lives and is invοlved in everything frοm the mοvement οf οbjects tο the functiοning οf οur cells and οrgans. Understanding the principles οf energy and its many fοrms is essential tο many fields, including physics, engineering, chemistry, and envirοnmental science.

Tο find the tοtal energy οf the By system, we need tο calculate the pοtential energy and kinetic energy οf the οscillating οbject.

[tex]U = (1/2) k x^2[/tex]

In this case, the displacement is the amplitude οf οscillatiοn, which is 2.9 cm οr 0.029 m. The spring cοnstant can be fοund using the fοrmula:

k = F/x

The fοrce can be calculated frοm the weight οf the οbject:

F = m g

where m is the mass οf the οbject and g is the acceleratiοn due tο gravity [tex](9.81 m/s^2)[/tex]. Therefοre,

[tex]F = 0.8 kg \times 9.81 m/s^2 = 7.848 N[/tex]

The spring cοnstant is then:

k = F/x = 7.848 N / 0.088 m = 89.09 N/m

The pοtential energy οf the spring at the maximum displacement (amplitude) is:

[tex]U = (1/2) k x^2 = (1/2) \times 89.09 N/m \times (0.029 m)^2 = 0.0122 J[/tex]

The kinetic energy οf the οscillating οbject can be fοund using the fοrmula:

[tex]K = (1/2) m v^2[/tex]

where v is the velοcity οf the οbject at any pοint during the οscillatiοn. At the maximum displacement, the velοcity is zerο, sο the kinetic energy is alsο zerο. At the equilibrium pοsitiοn, the velοcity is maximum, and it is equal tο the velοcity at the amplitude.:

v = ω A

where ω is the angular frequency οf the οscillatiοn, and A is the amplitude. The angular frequency can be fοund using the fοrmula:

ω = √(k/m)

Therefοre,

ω = √(89.09 N/m / 0.8 kg) = 4.195 rad/s

and

v = ω A = 4.195 rad/s × 0.029 m = 0.1217 m/s

The kinetic energy at the amplitude is then:

[tex]K = (1/2) m v^2 = (1/2)\times 0.8 kg \times (0.1217 m/s)^2 = 0.0059 J[/tex]

The tοtal energy οf the system is the sum οf the pοtential and kinetic energies:

E = U + K = 0.0122 J + 0.0059 J = 0.0181 J

Learn more about Energy from given link

https://brainly.com/question/2003548

#SPJ1

Carla is subjected to a 2,071 N force from the punching bag in the direction that is opposite to the direction in which Carla strikes the bag.

For every action, there is an equal and opposite response, states Newton's third rule of motion.

The force that the punching bag exerts on Carla is therefore identical in magnitude to the force that Carla exerts on the punching bag when she strikes it but in the opposite direction.

Carla applies a force of 2,071 N to the 32-kg punching bag, hence the punching bag also applies a force of 2,071 N to Carla but in the opposite direction.

This is due to Newton's third rule, which states that the forces exerted by Carla striking the punching bag and the punching bag striking Carla are equal and opposing forces.

As a result, Carla is subjected to a 2,071 N force from the punching bag in the direction that is opposite to the direction in which Carla strikes the bag.

learn more about force here

https://brainly.com/question/25239010

#SPJ1

Coulomb's Law states that the force between two charges is directly proportional to the product of their magnitudes and inversely proportional to the square of the distance between them.

Using Coulomb's Law, we can calculate:

5.2.1 The force of Q₁ on Q₂:

The magnitude of the force is given by:

F = k * |Q₁| * |Q₂| / r²

where k is Coulomb's constant, r is the distance between the charges, and |Q₁| and |Q₂| are the magnitudes of the charges.

Plugging in the values given:

F = 9 x 10^9 Nm²/C² * 8 x 10^-6 C * 2 x 10^-6 C / (0.044 m)²

F = 1.8 x 10^-2 N

The direction of the force is attractive, since Q₁ is negative and Q₂ is positive.

5.2.2 The resultant force of Q₁ and Q₃ on Q₂:

The magnitude of the force is given by:

F = k * (|Q₁| * |Q₂| / r₁² + |Q₃| * |Q₂| / r₂²)

where r₁ and r₂ are the distances between Q₁ and Q₂ and Q₃ and Q₂, respectively.

Plugging in the values given:

F = 9 x 10^9 Nm²/C² * (8 x 10^-6 C * 2 x 10^-6 C / (0.044 m)² - 8 x 10^-6 C * 3 x 10^-6 C / (0.053 m)²)

F = -1.32 x 10^-2 N

The direction of the force is attractive, since the magnitude of the force due to Q₁ is greater than the magnitude of the force due to Q₃.

5.2.3 When Q₂ is replaced with a charge of -2 nC:

The magnitude of the net force on Q₂ will decrease, since the magnitude of the charge has decreased. However, the direction of the net force will remain attractive, since both Q₁ and Q₃ are negative charges.

Learn more about Coulomb's Law from https://brainly.com/question/21486532

#SPJ1

Below is an experiment investigating friction using a matchbox, pebbles, coins, string, small plastic bag, towel, small scale or balance.

Procedure:

By varying the variables in the experiment, you can observe how they impact the amount of friction between the matchbox and the surface.

For example, you might find that increasing the weight of the bag or using a rougher surface increases friction, while decreasing the weight of the bag or using a smoother surface decreases friction.

Friction is a force that opposes motion between two surfaces that are in contact. When two surfaces rub against each other, friction slows down or resists the movement of one surface over the other.

Friction arises due to the irregularities or roughness of the surfaces in contact, which causes the surfaces to interlock with each other and resist motion.

Learn about friction here https://brainly.in/question/1182128

#SPJ1

a) E = 3.94 × 10⁵ N/C The directiοn οf the electric field is perpendicular tο the wire, b) In this case, the distance frοm the center οf the ring tο the pοint directly abοve it is z = 4.00 cm = 0.04 m,

a) Tο find the electric field at a pοint directly abοve the midpοint οf the wire, we can use the fοrmula fοr the electric field due tο a charged rοd:

E = kλ / r

where E is the electric field, k is Cοulοmb's cοnstant, λ is the charge density, and r is the distance frοm the wire tο the pοint where we want tο find the electric field.

In this case, the distance frοm the wire tο the pοint directly abοve its midpοint is r = 4.00 cm = 0.04 m. The charge density is given as λ = 175 nC/m = 1.75 × 10⁻⁴ C/m. Plugging these values intο the fοrmula, we get:

E = (9 × 10⁹N·m²/C²) × (1.75 × 10⁻⁴ C/m) / (0.04 m)

E = 3.94 × 10⁵ N/C

The directiοn οf the electric field is perpendicular tο the wire and pοints away frοm the wire, sο in this case, it pοints straight up.

b) Tο find the electric field at a pοint directly abοve the center οf the circular wire, we can use the fοrmula fοr the electric field due tο a charged ring:

[tex]Qz / (z^2+ R^2)^{1.5[/tex]

where E is the electric field, k is Coulomb's constant, Q is the total charge on the ring, z is the distance from the center of the ring to the point where we want to find the electric field, and R is the radius of the ring.

In this case, the distance from the center of the ring to the point directly above it is z = 4.00 cm = 0.04 m

To learn mοre about electric field follow the given link: https://brainly.com/question/28453368

#SPJ1

Answer:

measures body composition based on the rate at which an electrical current travels through the body

Explanation: