a sample is sent to the laboratory for an anti-xa assay. the result of the ptt is 65.7 seconds. the result of the anti-xa assay is 0.9 u/ml of heparin. the patient is on lovenox. their anti-xa level is:

676.1 kg of cryolite will be produced in this reaction.

In order for 14.8 kg of Al2O3(s), 56.4 kg of NaOH(l), and 56.4 kg of HF(g) to completely react, 8.8 kg of cryolite will be produced. This can be determined by performing a simple mole-to-mole conversion.

The moles of each reactant. Al2O3(s) has an atomic mass of 101.96, NaOH(l) has an atomic mass of 39.997, and HF(g) has an atomic mass of 20.01.

Therefore, the moles of Al2O3(s) are 14.8/101.96 = 0.145 moles, the moles of NaOH(l) are 56.4/39.997 = 1.41 moles, and the moles of HF(g) are 56.4/20.01 = 2.81 moles.

Convert the moles of each reactant to moles of cryolite. The chemical equation for the reaction is:

Al2O3(s) + 2NaOH(l) + 3HF(g) = 2Na3AlF6(s) + 3H2O(l)

This means that the ratio of Al2O3(s) to Na3AlF6(s) is 1:2, the ratio of NaOH(l) to Na3AlF6(s) is 2:2, and the ratio of HF(g) to Na3AlF6(s) is 3:2.

Using this ratio, the moles of Na3AlF6(s) (cryolite) produced can be calculated.

The moles of Na3AlF6(s) produced are 0.145/1 x 2 = 0.290 moles, 1.41/2 x 2 = 1.41 moles, and 2.81/3 x 2 = 1.87 moles. This gives a total of 0.290 + 1.41 + 1.87 = 3.6 moles of Na3AlF6(s).

Convert the moles of Na3AlF6(s) to kilograms. Na3AlF6(s) has an atomic mass of 187.3.

Therefore, the kilograms of Na3AlF6(s) produced are 3.6 x 187.3 = 676.1 kg. Since 1 kg of Na3AlF6(s) is equal to 1 kg of cryolite, 676.1 kg of cryolite will be produced in this reaction.

to know more about cryolite refer here:

https://brainly.com/question/14516036#

#SPJ11



The maximum wavelength of light required to ionize a single potassium atom is 283.6 nm.

What is Wavelength?

Wavelength is the distance between two consecutive points in a wave that are in phase with each other. It is often denoted by the Greek letter lambda (λ) and is usually measured in meters, although it can also be measured in other units such as nanometers or micrometers. Wavelength is a fundamental characteristic of waves and is related to other wave properties such as frequency and wave speed.

To calculate the maximum wavelength of light required to ionize a single potassium atom, we can use the formula:

λ = hc/E

where λ is the maximum wavelength, h is Planck's constant , c is the speed of light , and E is the first ionization energy of potassium in joules.

First, we need to convert the first ionization energy of K from kJ/mol to joules per atom:

419 kJ/mol / (6.022 x[tex]10^{23}[/tex] atoms/mol) = 6.973 x [tex]10^{-19}[/tex] J/atom

Now we can plug in the values and solve for λ:

λ = (6.626 x[tex]10^{34}[/tex]J s) x (2.998 x [tex]10^{8}[/tex] m/s) / (6.973 x [tex]10^{-19}[/tex] J/atom)

λ = 283.6 nm

Learn more about Wavelength  from the given link

https://brainly.com/question/10750459

#SPJ1

If two surface water types with the same density but different salinities and temperatures mix, the resulting water will be denser than both the surface water types.

Areas under warm and high salinity surface water with an appreciable depth, the temperature and salinity decreases with depth and internal vertical mixing processes occur despite stability of the water column. Eventually, this phenomenon is caused by the ability of the sea water to lose or gain heat by conduction and loss or gain of salt takes place by diffusion. This causes the density of the moving water to change directions.

Salt water mixes over limited depths and forms homogenous layers.

To know more about surface water here

https://brainly.com/question/25147725

#SPJ4

The addition of low ionic strength solution (LISS) to the testing environment when performing an indirect antiglobulin test is designed to enhance the speed and sensitivity of the test.

The LISS solution reduces the time required for the agglutination reaction to occur between the patient's red blood cells (RBCs) and antiglobulin reagent (Coombs reagent).This reagent is an anti-human globulin (AHG) that attaches itself to the antibodies present on the RBCs' surface. The test is an indirect antiglobulin test, which involves incubating the patient's RBCs with a known anti-human globulin. The LISS solution's addition to the testing environment increases the speed and sensitivity of the test. It also helps in reducing the reaction time and helps detect antibodies that are present in low concentrations.

The LISS solution enhances the sensitivity of the antiglobulin test by reducing the ionic strength of the testing environment. This solution neutralizes the ionic charges on the surface of the RBCs, allowing the AHG to attach itself to the RBCs' antigens more efficiently. This, in turn, promotes more efficient agglutination and quicker antibody detection during the indirect antiglobulin test.

Learn more about antiglobulin test at:

https://brainly.com/question/30707881

#SPJ11

The balanced equation for combustion of C3H8 with O2 is:

C3H8 + 5O2 → 3CO2 + 4H2O. the correct answer is option. d.

From equation, it can be seen that 1 mole of C3H8 reacts with 5 moles of O2. Given that 8 moles of O2 were present, this is in excess of required amount, so all of the C3H8 will react completely.

Therefore, 5 moles of O2 will be used up in the reaction, leaving 3 moles of O2 remaining. The molar percent of O2 remaining can be calculated as follows: Molar percent of O2 remaining = (3 moles O2 / 8 moles total) x 100% = 37.5% . Therefore, answer is closest to option (d) 30 mol %.

To know more about combustion, here

brainly.com/question/15117038

#SPJ4

An organic solvent is a liquid that has the ability to dissolve, extract, or suspend another substance to make a solution. An important organic solvent is acetone. The correct option is A.

An organic solvent is a liquid that has the ability to dissolve, extract, or suspend another substance to make a solution. Organic solvents are essential in a variety of industries, including pharmaceuticals, agriculture, paints, coatings, cleaning, and printing, among others.

They are used in the formulation of many products that we use in our daily lives. For example, in the paint and coatings industry, organic solvents are used to dissolve and disperse the ingredients of the paint, which then evaporates, leaving behind a solid coating.

Among the options given, acetone is the most important organic solvent. It is a colorless, flammable liquid that has a distinctive sweet odor.

Acetone is a versatile solvent that is used in a wide range of industries, including the production of chemicals, plastics, and fibers. It is also used as a solvent in paint, ink, and varnish, and it is used as a cleaning agent in a variety of applications.

Additionally, acetone is used in the manufacture of pharmaceuticals and cosmetics. It is also used as a fuel additive and a solvent in the production of biodiesel.

Among the other options given, menthone, phenol, and citral are not organic solvents. Menthone is a terpenoid that is used in the flavor and fragrance industry.

Phenol is an aromatic compound that is used as an antiseptic and disinfectant. Citral is a fragrance compound that is used in the production of perfumes and other fragrances.

To know more about Organic solvent refer here:

https://brainly.com/question/28850026#

#SPJ11

The final molarity of HCl of the resulting solution when 5.56 ml of 2.896 m HCl is added to 4.44 ml of water is 1.61 m.

The final molarity of HCl in the resulting solution can be calculated using the formula:

M₁V₁ = M₂V₂

where M₁ and M₂ are the concentrations of the first HCl solution and the resulting solution, and V₁ and V₂ are the volumes of the first solution and the resulting solution.

For this particular question, M₁ is equal to 2.896 mol/L, V₁ is equal to 5.56 mL, and V₂ is equal to (5.56 + 4.44) = 10 mL.

Substituting in the values, we can get the final concentration in molarity of the resulting solution.

M₂ = M₁V₁ / V₂

M₂ = (2.896 mol/L)(5.56 mL) / 10 mL

M₂ = 1.61 mol/L

In summary, when 5.56 mL of 2.896 m HCl is added to 4.44 mL of water, the final molarity of HCl in the resulting solution is 1.61 mol/L.

Learn more about molarity here: https://brainly.com/question/17138838.

#SPJ11

The Ka of a 0.010m acid solution which is 19% ionized is 4.5x10-4.

The Ka of an acid is the measure of its acidity and is calculated by dividing the concentration of its products by the concentration of its reactants.

To calculate the Ka of a 0.010m acid solution, we need to know the concentration of the products, which is 19% ionized.

To calculate the concentration of the products, we need to multiply the concentration of the acid (0.010M) by the percentage of ionization (19%). This gives us the concentration of the products as 0.0019M.

Now, we can calculate the Ka of the acid by dividing the concentration of the products (0.0019M) by the concentration of the reactants (0.010M). This gives us a Ka value of 4.5x10-4.

To know more about percentage of ionization click on below link:

https://brainly.com/question/30354044#

#SPJ11

Answer:

alpha particles have the least penetration power while beta particles have a moderate penetration power and gamma particles have the highest penetration power.

The principal organic product formed in the reaction of ethylene oxide with sodium cyanide (NaCN) in aqueous ethanol is ethylene cyanohydrin ([tex]C_{2}H_{5}CN[/tex]). The reaction follows this general reaction scheme:

Ethylene oxide + NaCN     →   Ethylene cyanohydrin + NaOH

The principal organic product formed in the reaction of ethylene oxide with sodium cyanide (NaCN) in aqueous ethanol is ethyl nitrile ([tex]C_{2}H_{5}CN[/tex]).

What is Ethyl nitrile?

Ethyl nitrile is an organic compound with the chemical formula [tex]C_{2}H_{5}CN[/tex]. This colorless liquid is a component of some commonly used solvents and in the manufacture of pharmaceuticals, textiles, and insecticides. It is used to generate pesticides, pharmaceuticals, and synthetic rubber during synthesis. The principal organic product formed in the reaction of ethylene oxide with sodium cyanide (NaCN) in aqueous ethanol is ethyl nitrile ([tex]C_{2}H_{5}CN[/tex]).

Mechanism of Reaction: The reaction between ethylene oxide and sodium cyanide in aqueous ethanol is carried out by the Saponification of Cyanide. Saponification refers to the reaction of a base with a fatty acid to create a soap.

The ethylene oxide undergoes nucleophilic attack by the hydroxide ion to produce a salt. The sodium ethylene oxide salt reacts with NaCN to form an intermediate. This intermediate reacts with [tex]H_{2} O[/tex]to form Ethyl nitrile. Ethylene oxide is a toxic, flammable, and colorless gas. It is used as a sterilant for medical equipment and as a fumigant for spices and foods. It has a sweet odor and can cause eye and respiratory irritation, as well as skin burns. The reaction of ethylene oxide with NaCN in aqueous ethanol generates Ethyl nitrile, which is used in a variety of industries.

For more questions related to ethylene cyanohydrin.

https://brainly.com/question/14919939

#SPJ11

Yes, you have enough sulfur for three trials. This is because 1.9 g of sulfur is equal to 0.09 mol, which is enough to do three trials of 0.030 mol each. Use the molar mass of sulfur, which is 32 g/mol.

Convert the mass of sulfur given to moles.

1.9 g / 32 g/mol = 0.09 mol

The moles by the number of trials you need to do:

0.09 mol x 3 trials = 0.27 mol

The moles back to grams to make sure you have enough sulfur:

0.27 mol x 32 g/mol = 8.64 g

Since the amount of sulfur given is more than the amount you need for the three trials (1.9 g > 8.64 g), you have enough sulfur.

to know more about sulfur refer here:

https://brainly.com/question/1478186#

#SPJ11

To calculate the change in entropy when 1 mole of ethanol condenses at its boiling point of 78.3°C, we can use the formula:

ΔS = q/T

where ΔS is the change in entropy, q is the heat of vaporization, and T is the boiling point of ethanol in Kelvin.

First, we need to convert the boiling point of ethanol from Celsius to Kelvin by adding 273.15:

T = 78.3°C + 273.15 = 351.45 K

Then, we can substitute the values:

ΔS = -40.5 kJ/mol / 351.45 K

ΔS = -0.115 kJ/(mol·K)

Therefore, the change in entropy when 1 mole of ethanol condenses at its boiling point is -0.115 kJ/(mol·K). This negative value indicates that the process is exothermic and that the system becomes more ordered.

For more details about entropy click here:

https://brainly.com/question/13135498#
#SPJ11

The blank can be filled with the term "shielding gas."Shielding gas protects the molten weld pool, the filler rod, and the tungsten electrode as they cool to a temperature at which they will not oxidize rapidly.

What is a shielding gas? A shielding gas is a gas that is employed in gas welding processes to safeguard the weld area from contamination. Welding processes that use shielding gases are referred to as gas metal arc welding or gas tungsten arc welding, among other things. What is the purpose of shielding gas in welding? The primary goal of shielding gas in welding is to defend the molten weld pool, the filler rod, and the tungsten electrode from being contaminated. When the shielding gas is utilized, it forms a sort of barrier that protects the weld from the air and other contaminants. In essence, the shielding gas creates a shield for the welding process that protects the molten weld pool from getting contaminated. As a result, the use of shielding gas is critical in ensuring that the welding process results in high-quality welds.

Learn more about molten weld pool at  brainly.com/question/30024003

#SPJ11

To determine the percent yield, we need to first calculate the theoretical yield of the reaction using stoichiometry, and then divide the actual yield by the theoretical yield and multiply by 100%. The percent yield of the reaction is approximately 84.9%.

Percent yield is a measure of the efficiency of a chemical reaction, calculated by dividing the actual yield of a reaction by the theoretical yield and multiplying by 100%. It represents the percentage of the theoretical amount of product that was actually obtained in a reaction.

The balanced chemical equation is:

2Al + Cr₂O₃ → Al₂O₃ + 2Cr

The molar mass of Cr₂O₃ is 152 g/mol, the molar mass of Al is 27 g/mol, and the molar mass of Cr is 52 g/mol.

We need to determine which reactant is limiting, so we can calculate the theoretical yield based on the amount of limiting reactant. We can do this by calculating the number of moles of each reactant using their molar masses and dividing by their stoichiometric coefficients in the balanced equation:

moles of Cr₂O₃= 44.1 g / 152 g/mol = 0.29 mol

moles of Al = 35.0 g / 27 g/mol = 1.30 mol

From the balanced equation, we see that 1 mole of Cr2O3 reacts with 2 moles of Cr. Therefore, the theoretical yield of Cr is:

moles of Cr produced = 0.29 mol Cr₂O₃x (2 mol Cr / 1 mol Cr₂O₃) = 0.58 mol Cr

mass of Cr produced = 0.58 mol Cr x 52 g/mol = 30.16 g Cr

The percent yield is:

% yield = (actual yield / theoretical yield) x 100%

% yield = (25.6 g Cr / 30.16 g Cr) x 100% = 84.9%

Therefore, the percent yield of the reaction is approximately 84.9%.

To find out more about percent yield, visit:

https://brainly.com/question/17042787

#SPJ1

In order to make a solution that is 1.5ppm in fluoride ion using sodium fluoride (NaF), 750L of water needs to be added to 0.22g of NaF.

Mass of NaF (g) = Concentration of F (ppm) x Volume of Water (L) / 1,000,000.

NaF mass = 1.5ppm x 750L / 1,000,000.

Since the atomic weight of NaF is 41.99, 0.22g is equivalent to 0.00518mol NaF.

The molarity (M) of the solution,

Molarity (M) = Moles of Solute (mol) / Volume of Solution (L)

Molarity 0.00518mol / 750L = 0.000068M.

Therefore, 0.22g of NaF should be added to 750L of water to make a solution that is 1.5ppm in fluoride ion.

to know more about sodium fluoride refer here:

https://brainly.com/question/2807538#

#SPJ11

According to the VSEPR model, the electron-pair arrangement of the central atom in BH₃ is predicted to be trigonal planar.

VSEPR stands for Valence Shell Electron Pair Repulsion. It is a model used in chemistry to predict the shape of individual molecules based on the extent of electron-pair electrostatic repulsion. It is founded on the Lewis structure theory of bonding, which describes electron pairs as lone pairs and bonds. Furthermore, VSEPR is based on the idea that electrons repel one another because they are negatively charged.

The electron-pair arrangement of the central atom in BH₃ is predicted to be trigonal planar by the VSEPR model.

BH₃ is a boron atom bonded to three hydrogen atoms. Boron has three valence electrons, but it requires six valence electrons to satisfy the octet rule. This means that boron has a vacant p orbital that it can use to form a molecule. The three hydrogen atoms are covalently bonded to the boron atom, with each hydrogen atom sharing one electron pair with the boron atom.

Based on this electron-pair arrangement, the VSEPR model predicts that the molecule will have a trigonal planar geometry. This means that the three hydrogen atoms will be positioned around the boron atom at the corners of an equilateral triangle. This arrangement causes the electron pairs in the valence shell to be as far apart as possible, resulting in a repulsion-free arrangement that is energetically stable.

Thus, the structure of  BH₃  will be a trigonal planar.

To know more about the VSEPR Theory, refer here:

https://brainly.com/question/14574141#

#SPJ11

The equilibrium constant (Kc) is the ratio of the concentration of the products to the reactants at equilibrium. The value of Kc changes with the temperature but is constant at a given temperature.

The expression for the equilibrium constant Kc can be defined as follows:-

Kc = [C]^c[D]^d/[A]^a[B]^b

where [ ] denotes the molar concentration of the respective species. a, b, c, and d are the coefficients of the balanced chemical equation for the species A, B, C, and D.

If a chemical reaction is at equilibrium at a given temperature, the concentration of reactants and products remains constant over time. In other words, the rate of the forward reaction and the rate of the reverse reaction is equal.

The reaction for which we need to find the equilibrium constant is:-

HI(g)  ↔ H(g) + I(g)

Now, assume that initially there were 'x' moles of HI in the reaction mixture. After the dissociation of HI, the concentration of H and I will be equal to 'x - y' moles. The concentration of HI will be equal to 'x - y' moles.

Here, y is the number of moles of HI that dissociated. According to the given statement, HI is 40% dissociated. Therefore, the number of moles of HI that dissociated will be 0.4x. Similarly, the number of moles of H and I that will be formed will also be 0.4x.

The equation for the dissociation of HI can be written as:-

HI(g)  ↔ H(g) + I(g)

The initial number of moles = x Moles dissociated = 0.4x

At equilibrium, the number of moles of HI = x - 0.4x = 0.6x

Number of moles of H = 0.4x

Number of moles of I = 0.4x

Finally, substitute these values in the expression for the equilibrium constant:-

Kc = [H][I]/[HI]

Kc = (0.4x)(0.4x)/(0.6x)²

Kc = 0.16/0.36Kc = 0.4444 (approximately)

Therefore, the equilibrium constant Kc for the given reaction is 0.4444 (approximately).

Learn more about equilibrium constant: https://brainly.com/question/3159758

#SPJ11

The overall reaction of the multistep reaction is: 2A + B → C + D

This reaction can be broken down into two individual steps. In the first step, A and B react to form an intermediate product, X. The balanced chemical equation for this step is: A + B → X. In the second step, the intermediate product X is reacted with A to form C and D. The balanced chemical equation for this step is:X + A → C + D

Combining these two equations yields the overall balanced chemical equation:

2A + B → C + D

In summary, the overall balanced chemical equation for the multistep reaction is 2A + B → C + D. This equation shows that two molecules of A and one molecule of B will combine to form one molecule of C and one molecule of D.

To know more about chemical equation click on below link :

https://brainly.com/question/19626681#

#SPJ11

The theoretical yield in grams for the dehydration reaction of 4.00 ml of 2-methylcyclohexanol is 3.17E-5 g.

The theoretical yield in grams for the dehydration of 4.00 mL of 2-methylcyclohexanol can be calculated using the following steps:

1. 2-methylcyclohexanol has a molecular formula of C7H14O, so its molecular weight is 106 g/mol.

2. Since the question specifies 4.00 mL, we can convert that to 0.004 L. We can use the equation mass = volume x density to calculate the mass of 2-methylcyclohexanol used.

The density of 2-methylcyclohexanol is 0.841 g/mL, so the mass of 2-methylcyclohexanol used is 0.841 g/mL x 0.004 L, or 0.00336 g.

3. Since the molecular weight of 2-methylcyclohexanol is 106 g/mol, and the mass of 2-methylcyclohexanol used is 0.00336 g,  the equation yield = mass/molecular weight to calculate the theoretical yield.

The theoretical yield of the dehydration reaction is 0.00336 g/106 g/mol, or 3.17E-5 g.

In conclusion, the theoretical yield in grams for the dehydration reaction of 4.00 ml of 2-methylcyclohexanol is 3.17E-5 g.

to know more about 2-methylcyclohexanol refer here:

https://brainly.com/question/13915064#

#SPJ11

The anions, such as sulfate ([tex]SO_4^{2-}[/tex]), phosphate ([tex]PO_4^{3-}[/tex]), and nitrate ([tex]NO_3^-[/tex]), may be separated by anion-exchange liquid chromatography. This form of liquid chromatography is commonly used in the purification of proteins and nucleotides.

Anion-exchange chromatography separates anions on the basis of their charge and specificity to a particular resin. Anion-exchange chromatography separates ions by exchanging anions on a positively charged stationary phase with other anions in a solution of the sample of water.

Anion-exchange chromatography can be used to separate a wide range of anions in a single step, including organic acids and sulfur-containing compounds. Therefore, anion-exchange liquid chromatography is the most suited for separating sulfate ([tex]SO_4^{2-}[/tex]), phosphate ([tex]NO_3^-[/tex]), and nitrate ([tex]NO_3^-[/tex]) in a sample of water.

Learn more about chromatography at: https://brainly.com/question/11960023

#SPJ11

8.88 g is the greatest yield of Na2SO4 that may be produced. As a result of using less NaHCO3 than is required to fully react with the H2SO4, the actual number of NaHCO3 used.

The body requires the base chemical bicarbonate to maintain a healthy acid-base balance. Your body's natural pH balance keeps it from becoming overly acidic, which can lead to a variety of health issues. By eliminating extra acid, the kidneys and lungs maintain a normal blood pH.

Metabolic acidosis is indicated by low blood bicarbonate levels. It is an alkali, the antithesis of acid, and it can counteract acid. Our blood's acidity is kept under control by it.

To know more about Bicarbonate visit:

https://brainly.com/question/8560563

#SPJ1

The mass % of the solution if the density of the solution is 1.06 g/ml is 10.51%

The mass of NaI = 99.7 g

Volume of the solution = 895 ml

Density of the solution = 1.06 g/ml

To calculate the mass % of the solution, we have to calculate the mass of the solution first.

Step-by-step explanation:

The formula for density is given by:

Density = Mass/Volume

Or,

Mass = Density × Volume

Now, we will calculate the mass of the solution.

Mass = Density × Volume

        = 1.06 × 895= 948.7 g

Now, we will calculate the mass % of the solution.

Mass % = (Mass of solute/Total mass of solution) × 100

Mass of solute = 99.7 g

Total mass of solution = 948.7 g

Mass % = (99.7/948.7) × 100

             = 10.51%

Therefore, the mass % of the solution is 10.51%.

Learn more about mass %: https://brainly.com/question/26150306

#SPJ11

Acetaldehyde (CH3CHO) is a polar molecule due to its asymmetric shape and presence of polar covalent bonds.

The polarity is caused by the oxygen-hydrogen bond dipoles, as oxygen has a greater electronegativity than the hydrogen. This causes the oxygen to attract the electrons from the bond, creating a net dipole.

Acetaldehyde is a polar molecule. The polar character of a molecule is determined by the shape and polarity of its bonds. When the molecule has polar bonds and an asymmetrical shape, it is said to be polar. On the other hand, if it has no polar bonds or symmetrical shape, it is nonpolar.

Acetaldehyde is a polar molecule due to the electronegativity difference between carbon and oxygen, which creates a polar bond. It also has an asymmetrical shape due to the presence of two electronegative oxygen atoms on either side of the central carbon atom. As a result, acetaldehyde is soluble in polar solvents like water, ethanol, and acetone.

Read more about carcinogenic :

https://brainly.com/question/984334

#SPJ11

The reactivity (base strength) of a base has a direct correlation with its selectivity (regioselectivity). Generally speaking, stronger bases will be more selective and react faster than weaker bases.

This is due to the fact that stronger bases have greater electron-donating power which allows them to selectively bond to certain parts of the molecule more effectively. In the case of regioselectivity, stronger bases will generally form stronger bonds with certain parts of the molecule, such as electrophilic or acidic sites, than with others.

The correlation between reactivity (base strength) and selectivity (specifically regioselectivity) can be described as follows: When a base reacts with a proton, the bond between the base and the proton is broken, leaving a negative charge on the base. The base's reactivity (its tendency to accept a proton) is linked to its base strength. The greater the strength of a base, the more reactive it is.

Read more about the reactivity :

https://brainly.com/question/17746822

#SPJ11

To create 303 grams of hydrogen phosphoric acid, we need 246 grams of water. Phosphoric acid is a type of acid that is commonly used in the production of fertilizers, detergents, and other chemicals.

Phosphoric acid is also used in the food industry as a food additive. The molecular formula for phosphoric acid is H3PO4. It is a triprotic acid, meaning it can donate up to three hydrogen ions in solution. The balanced chemical equation for the reaction of water with phosphoric acid is as follows:H3PO4 + H2O → H3O+ + H2PO4-If we examine this equation, we can see that one mole of phosphoric acid reacts with one mole of water. The molar mass of phosphoric acid is 98 g/mol. Therefore, to create 98 grams of phosphoric acid, we would need 18 grams of water (which is one mole of water).

We are given that we need to create 303 grams of phosphoric acid. Therefore, we can use the following proportion to determine how much water we need: 98 g of phosphoric acid is to 18 g of water as 303 g of phosphoric acid is to x g of water Solving for x, we get: x = (18 g of water/98 g of phosphoric acid) * 303 g of phosphoric acid x = 55.173 grams of water

For more such questions on phosphoric acid, click on:

https://brainly.com/question/29947796

#SPJ11

The polarity of a molecule is determined by both the type of bonds and the shape of the molecule. Polar bonds result in a molecule being polar, while non-polar bonds result in a molecule being non-polar. The shape of the molecule can also affect the polarity of the molecule. Molecules that are symmetrical are non-polar, while those that are asymmetrical are polar.

Polar bonds occur when two atoms share electrons unequally, leading to a permanent dipole moment. These molecules are said to be polar. On the other hand, non-polar molecules occur when the atoms involved in the bond share electrons equally, resulting in a non-polar molecule.

The shape of the molecule also plays a role in determining the polarity of the molecule. If the shape of the molecule is symmetrical, with an equal distribution of electrons, then it is considered non-polar.  

Know more about dipole moment here:

https://brainly.com/question/14140953

#SPJ11

The correct answer is D. Reactants are substances that are combined to form products in a chemical reaction. Products are the result of substances being combined in a chemical reaction.

1) protons: 3

they're positive so they go in the middle

2) atomic mass (rounded): 7 minus the atomic number (7-4)=3 neurons

as neutrons are neither negative or positive they go in the middle as well

3) electrons: 3

the number of electrons is the same as protons so 3. they go on the outside as they are negative. Electrons never go in the center

If the value of ΔG° is equal to 0, then the value of K or Kp is equal to 1 and the system is said to be in equilibrium.

A change in temperature occurs when heat flow increases or decreases the temperature. This changes the chemical equilibrium towards the products or the reactants. This can be identified by examining the reaction and determining whether it is an endothermic reaction or an exothermic reaction.

If the temperature is raised, the equilibrium constant decreases. If the forward reaction has an endothermic nature, the equilibrium constant increases. The equilibrium position also changes when the temperature is changed.

To learn more about equilibrium, refer to the link:

https://brainly.com/question/30807709

#SPJ12