The formula for calculating capacitance is as follows:
C = Q/V
Where,
C = capacitance (Farads)
Q = charge (Coulombs)
V = voltage (Volts)
As given,
Q = 27.0 μC
V = 9.00 V
Substituting the given values in the above equation
C = 27.0 μC/9.00 V = 3.00 μF
Therefore, the value of capacitance is 3.00 μF.
The formula for calculating charge stored is as follows:
Q = CV
Where,
Q = charge (Coulombs)
C = capacitance (Farads)
V = voltage (Volts)
As given,
C = 3.00 μF
V = 12.0 V
Substituting the given values in the above equation,
Q = (3.00 × 10⁻⁶ F) × 12.0 V = 36.0 μC
Therefore, the charge stored is 36.0 μC.
Learn more about the charge stored at https://brainly.com/question/27393410
#SPJ11
two stationary point charges q1 and q2 are shown in the figure along with a sketch of some field linesrepresenting the electric field produced by them. what can you deduce from the sketch?
From the sketch, we can deduce that the two charges q1 and q2 are of opposite signs, as field lines start at the positive charge q1 and end at the negative charge q2. The field lines also indicate that the magnitude of the electric field produced by q1 is larger than that of q2.
Additionally, the field lines show that the electric field lines near the charges are denser, indicating a stronger electric field intensity near the charges. The direction of the electric field points from q1 to q2, which is consistent with the direction of the force that a positive test charge would experience if placed in the field. The field lines also show that the electric field is radial, i.e., the field lines point directly away from or towards each charge in a straight line, which is a characteristic of the electric field produced by a point charge. Finally, the density of the field lines decreases with distance from the charges, indicating that the electric field strength decreases with distance from the charges, following an inverse-square law.Learn more about electric field at: https://brainly.com/question/14372859
#SPJ11
a mass-spring oscillating system undergoes shm with a period t. what is the period of the system if the amplitude is doubled?
The period of a mass-spring oscillating system undergoing SHM with a period t, when the amplitude is doubled, is still t.
The period of a mass-spring oscillating system undergoing simple harmonic motion (SHM) is determined by the spring constant and mass of the system.
When the amplitude of the system is doubled, the period of the system remains the same, regardless of the amplitude. This means that the period of a mass-spring oscillating system undergoing SHM with a period t, when the amplitude is doubled, is still t.
To understand why the period remains the same, consider the equation for simple harmonic motion:
x(t) = A cos (2πft).
This equation describes the displacement of an object over time and is based on the principle that any system undergoing SHM oscillates about a fixed point at a constant frequency.
The frequency of the system is inversely proportional to the period, and is determined by the spring constant and mass of the system.
Increasing the amplitude of the system does not affect the frequency or period of the oscillations.
For similar question on oscillating system
https://brainly.com/question/14051226
#SPJ11
a 10.0-mf capacitor is fully charged across a 12.0-v bat- tery. the capacitor is then disconnected from the battery and connected across an initially uncharged capacitor with capacitance c. the resulting voltage across each capacitor is 3.00 v. what is the value of c?
The value of uncharged capacitor in series with a 10.0-microfarad capacitor, given that each capacitor has a voltage of 3.00 volts, can be calculated using the formula for equivalent capacitance in series and formula for charge on a capacitor. The value of c is approximately 4.00 microfarads.
To determine the value of c, which is [tex]1/Ceq = 1/C1 + 1/C2[/tex] . Initially, the 10.0-microfarad capacitor has a charge of [tex]Q = CV = (10.0 * 10^{-6 }F) * 12.0 V = 1.20 * 10^{-4} C[/tex].
When it is connected in series with uncharged capacitor with capacitance c, charge is shared between the two capacitors. The charge on 10.0-microfarad capacitor is also equal to the charge on uncharged capacitor, which is given by [tex]Q = (3.00 V) * C[/tex] .
Equating the two expressions for Q and solving for c, we get [tex]C = Q/3.00[/tex] [tex]V = (1.20 * 10^{-4 C}) / (3.00 V) = 4.00 * 10^{-5 F}[/tex]. Therefore, value of c is approximately 4.00 microfarads.
To know more about equivalent capacitance, here
brainly.com/question/30905469
#SPJ4
a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet. the coefficients of static and kinetic friction are 0.6 and 0.4, respectively. the worker pushes with a force of 600 n. the frictional force exerted by the surface is
When a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet, the frictional force exerted by the surface on the crate is 588 N.
When a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet, the frictional force exerted by the surface can be calculated as follows:
The weight of the crate = m × g = 100 kg × 9.8 m/s² = 980 N
Force applied by the worker = F = 600 N
The force of friction acting on the crate is given by the following formula:
Ff = μF
Where, μ is the coefficient of friction, F is the normal force acting on the crate.
Notes: The normal force is equal and opposite to the weight of the crate. i.e., N = 980 N1. The frictional force exerted by the surface on the crate is the static frictional force initially. Hence, we use the coefficient of static friction for our calculation.
2. If the force applied by the worker is not enough to overcome the static frictional force, then the crate will not move and the frictional force will remain static friction.
3. Once the crate starts moving, the static friction will convert to kinetic friction. Hence, we will use the coefficient of kinetic friction if the force applied by the worker is greater than the force of static friction. Initially, the force applied by the worker is less than the force of static friction, hence the frictional force exerted on the crate will be the static frictional force.
Frictional force = Ff = μN
The normal force acting on the crate = Weight of the crate = 980 N
Frictional force =
Ff = μN
= 0.6 × 980 N
= 588 N
Therefore, the frictional force exerted by the surface on the crate is 588 N.
For more such questions on frictional force , Visit:
https://brainly.com/question/4618599
#SPJ11
water flows through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s. the density of water is 1 000 kg/m3. determine its average velocity. multiple choice question. 20 m/s 200 m/s 0.02 m/s 2 m/s 0.2 m/s
Option D: 2 m/s is the average velocity of the water flowing through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s.
According to the question:
cross-sectional area of the pipe = 0.002m²
Mass flowrate = 4 kg/s
Density of water = 1000 kg/m³
We are asked to find, average velocity =?
Average velocity is the net or total displacement covered by a body in a given time. The mass flow rate divided by the pipe's cross-sectional area and density ratio is the formula for calculating a fluid's average velocity.
As a result, the water's average flow rate through the pipe is provided by:
v = m / (ρ × A)
where, v is the average velocity, m is the mass flow rate, ρ is the density of water, and A is the cross-sectional area of the pipe. Substituting the values in the above equation we get:
v = 4 / (1000 × 0.002)
v = 2m/s
Therefore, the average velocity of water flowing through a pipe of cross-sectional area of 0.002m² is 2m/s.
To know more about average velocity, refer:
https://brainly.com/question/13243044
#SPJ4
Correct question is:
Water flows through a pipe with a cross-sectional area of 0.002 m2 at a mass flow rate of 4 kg/s. The density of water is 1 000 kg/m3. Determine its average velocity. Multiple choice question.
20 m/s
200 m/s
0.02 m/s
2 m/s
0.2 m/s
if a current of 5.5 a is used, what is the force generated per unit field strength on the 20.0 cm wide section of the loop? use units of newtons per tesla.
The force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is: 0.001 newtons per tesla
The force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is given by the formula F = (μI) / 2πr,
where μ is the permeability of free space, (4π x 10-7 N/A²)
I is current, and r is the radius of the loop.
In this case, the force is (4π x 10-7 x 5.5) / (2π x 0.1) = 0.001 N/T.
In other words, the force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is 0.001 newtons per tesla.
The formula for the force generated per unit field strength on a loop is derived from the fact that the force is a result of the magnetic field generated by the current flowing in the loop.
The magnitude of the magnetic field generated is proportional to the current and inversely proportional to the radius of the loop. Since the force is a product of the current and the magnetic field, it is proportional to the square of the current and inversely proportional to the square of the radius of the loop.
In summary, the force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is 0.001 newtons per tesla, given by the formula F = (μI) / 2πr, where μ is the permeability of free space (4π x 10-7 N/A²), I is current, and r is the radius of the loop.
To know more about force refer here:
https://brainly.com/question/13191643#
#SPJ11
Why is momentum not conserved in real life situations
Momentum is not always conserved in real-life situations because external forces can act on a system and change its momentum.
For example, when two cars collide, friction and air resistance can cause the momentum of the system to change. Similarly, when a ball is thrown in the air, gravity and air resistance act on it and cause its momentum to change. Other factors such as deformation, energy loss, and imperfect collisions can also cause momentum to be lost or gained. Therefore, while momentum is a useful concept in physics, it is important to consider the impact of external factors when analyzing real-world situations.
To know more about momentum, here
brainly.com/question/30677308
#SPJ4