An object of mass 50 g is attached to a string of length 50 cm which will break if tension is 20 N. The object is whirled in a vertical circle, the axis of rotation being at a height of 100 cm above the ground. The angular speed is very slowly increased until the string breaks. In what position is the week is likely to occur and of what angular speed? Where will the object hits the ground?​

It is important to note that wiring a plug can be dangerous, and if you are not confident in your ability to do so, you should seek the help of a qualified electrician. Incorrectly wiring a plug can result in electrical shock.

What are the step for plug wired ?

The first change that may need to be made is to ensure that the correct wires are connected to the corresponding terminals on the plug. Typically, the green and yellow wire is connected to the earth terminal, the blue wire to the neutral terminal, and the brown wire to the live terminal.

Voltage can be measured with a multimeter. A probe should be inserted into each slot to measure the line voltage. A fully functioning outlet registers between 110 and 120 volts. Check the outlet and the wiring if there is no reading.

To know more about wiring visit:-

https://brainly.com/question/26064065

#SPJ1

Hence, R = 28.97 m, 24.5 degrees is the vector sum of T and U.

A vector's direction is frequently stated as a rotation of the vector's "tail" anticlockwise with respect to due East. In accordance with this practise, a vector having a direction of 30 degrees is a vector that has been anticlockwise rotated 30 degrees with respect to due east.

Let's begin by separating the components of the vector T:

T~ = 40 m, 30 degrees

T_x = 40 cos(30) = 34.64 m

T_y = 40 sin(30) = 20 m

Let's now decompose the vector U into its constituent parts:

U~ = 12 m, 225 degrees

U_x = 12 cos(225) = -8.49 m

U_y = 12 sin(225) = -8.49 m

It is possible to combine elements of the same type (x and y):

R_x = T_x + U_x = 34.64 m - 8.49 m = 26.15 m

R_y = T_y + U_y = 20 m - 8.49 m = 11.51 m

The Pythagorean theorem can be used to determine the size of the resulting vector R:

|R~| = sqrt(R_x² + R_y²) = sqrt((26.15 m)² + (11.51 m)²) = 28.97 m

The inverse tangent function can be used to determine the direction of the resulting vector R:

theta = tan⁻¹(R_y/R_x) = tan⁻¹(11.51 m/26.15 m) = 24.5 degree.

To know more about vector visit:-

https://brainly.com/question/30512630

#SPJ1

The tire rotates at a rate of 223.7 rpm, while the frequency  layer of a tire is moving at a rate of 24.0 m/s plus 7.50 m/s, or 31.5 m/s. 24.0 m/s - 7.50 m/s = 16.5 m/s is the speed of a spot on the tire's bottom edge.

Frequency refers to the quantity of waves passing a defined location in a predetermined period of time. As a result, the rate is 2 per second if a wave passes through in 1/2 of a second. In this case, the rate is 100 times per hour if it takes 1/10 of an hour.

The quantity of observations that take place during a specific predetermined timeframe is the frequency of such a class interval. So, the frequency for such 5–9 age range is 20 if, for instance, 20 individuals between the ages of 5 and 9 exist in the study's data.

To know more about frequency visit:

https://brainly.com/question/2140860

#SPJ1

Answer:

35J

Explanation:

The mass of the ball=2.5kg

The initial speed=10m/s

we have to calculate the height= h

s=ut+1/2at^2

h=10*0.2 -1/2*10*0.04

h=2-0.2

h= 1.8m

the potential energy= mgh

                                 = 2.5kg*10*1.8

                                = 25*1.8

                                 = 35J

Answer: false

Explanation:

To accurately measure the distance traveled by the fire ants, we could use a measuring tape or a GPS device. For short distances, a measuring tape would suffice, while for longer distances, a GPS device would provide more accurate measurements.

How to investigate the distance traveled by fire ants to collect resources?

To investigate the distance traveled by fire ants to collect resources, we could follow the following plan:

To learn more about GPS device, visit: https://brainly.com/question/14996387

#SPJ1

Answer:

Explanation:

The rate of heat transfer from the transistor to the heat sink through the mica sheet can be calculated using Fourier’s Law of heat conduction. The formula for this law is Q = kA(T1 - T2)/d where Q is the rate of heat transfer, k is the thermal conductivity of the material, A is the cross-sectional area through which heat is transferred, T1 and T2 are the temperatures at either end of the material and d is its thickness.

In this case, we know that Q = 1.00 W (the rate at which energy enters the device), k = 0.0753 W/m·°C (the thermal conductivity of mica), A = 8.25 mm * 6.25 mm = 5.15625e-5 m² (the cross-sectional area of the mica sheet), T2 = 35°C (the temperature of the heat sink) and d = 0.0852 mm = 8.52e-5 m (the thickness of the mica sheet).

Substituting these values into Fourier’s Law gives us:

1.00 W = (0.0753 W/m·°C)(5.15625e-5 m²)(T1 - 35°C)/(8.52e-5 m)

Solving for T1 gives us:

T1 ≈ 35 + (1 / ((0.0753 * 5.15625e-5) / 8.52e-5)) ≈ 35 + 22 ≈ 57°C

So under steady-state conditions with an energy input rate of 1 W and a heat sink temperature of 35°C, we can expect that the operating temperature of this power transistor would be approximately 57°C.

Answer:

Metals, nonmetals, and metalloids are three different categories for the elements. Metals may be hammered into sheets and are malleable, ductile, and excellent conductors of heat and electricity (they can be drawn into wire).

Explanation:

Brainliest pls

Answer:

A. Non-metals, metals, metalloids

Explanation:

metals are Group I, II and III and IV

Non metals are Group VII, VI and VIII

Answer

explanation

requirments

37. Segment B of the graph corresponds to the only solid state. ,38. Segment E of the graph corresponds to the melting point. and all answer given below:

Segment is a customer data platform (CDP) that enables businesses to collect, store, and analyze customer data from multiple sources. It allows companies to unify their customer data into one place, which can then be used to create more personalized customer experiences. With Segment, businesses can create custom segments of their customers and create targeted campaigns to meet their specific needs.

39. The melting point (temperature) is 300°C.

40. Segment F of the graph corresponds to the only liquid state.

41. Segment A of the graph corresponds to the only gas state.

42. Segment D of the graph corresponds to the boiling point.

43. No, the temperature decreases during freezing.

44. Segment C of the graph corresponds to the freezing point.

45. The boiling point (temperature) is 450°C.

To learn more about Segment
https://brainly.com/question/30436465
#SPJ1

Answer:

The force acting on the train due to the air resistance is given by the formula:

F = (1/2) * p * A * v^2 * Cd

where p is the density of air, A is the cross-sectional area of the train, v is the speed of the train, and Cd is the drag coefficient.

We can assume that the drag coefficient is constant for a given shape of the train, and we can take it to be 0.5 for a train moving through air.

The pressure difference between the front and back of the train is given by:

P = (1/2) * p * v^2

The pressure difference between the sides of the train and the tunnel walls is given by:

2 * P = 2 * (1/2) * p * v^2 = p * v^2

The force acting on the train due to this pressure difference is given by:

F' = 2 * P * S = 2 * p * v^2 * S

The net force acting on the train is given by:

Fnet = F - F' = (1/2) * p * A * v^2 * Cd - 2 * p * v^2 * S

We can simplify this expression by factoring out p * v^2:

Fnet = p * v^2 * [(1/2) * A * Cd - 2 * S]

We are given that So = 4St, so we can substitute A = St and S = St/4:

Fnet = p * v^2 * [(1/2) * St * Cd - 1/2 * St * Cd] = 0

Therefore, the net force acting on the train is zero. This means that the force due to air resistance is exactly balanced by the force due to the pressure difference between the sides of the train and the tunnel walls.

We are given that Po - P = 2 * Pu, so we can substitute P = (1/2) * Po - Pu:

F' = 2 * P * S = 2 * [(1/2) * Po - Pu] * S = (Po - Pu) * 4 * St

We can equate this expression for F' to the expression for air resistance force:

F' = p * v^2 * [(1/2) * St * Cd - 2 * St/4] = p * v^2 * [(1/2) * St * Cd - St/2]

Equating these two expressions, we get:

(Po - Pu) * 4 * St = p * v^2 * [(1/2) * St * Cd - St/2]

Simplifying and solving for Pu, we get:

Pu = Po - (p * v^2 * Cd) / 8

We are given that Cd = 2N, so we can substitute this value:

Pu = Po - (p * v^2 * 2N) / 8

Pu = Po - (p * v^2 * N) / 4

Therefore, the pressure inside the train is Po - (p * v^2 * N) / 4.

Planck's frequency (h) and indeed the light's velocity (c) are used to connect a photon's energy (E) to its wavelength (), frequency (v), and wavelength. E = hν = hc/λ.

We frequently use the word "energy" in our everyday speech. Energy has an unique physical meaning even if the term is frequently used figuratively. Energy is defined in physics as something's capacity to perform work. Many types of energy are possible. All energy is kinetic in some way.

Energy is present everywhere and comes in a variety of shapes and sizes. Objects at rest have potential energy that, if released, will cause them to move. All moving things contain kinetic energy.

To know more about Energy visit:

https://brainly.com/question/1932868

#SPJ9

The explanation of each of their observations can be found below.

More on observations can be found here: https://brainly.com/question/28041973

#SPJ1

Answer: Applying a weight limit to a road is often done in an attempt to protect a roadway's appearance in particular. It also aims to protect the character and environment of rural areas, villages, and residential estates. Restricting overweight freights may just prevent damages like pot holes and cracks in the road.

Explanation:

I HOPE THIS HELPED GOOD LUCK AND I AM OPEN FOR FREE ANSWERS!

Answer: (0.17 * 6) + ( 0.16 * 0 ) = (0.17 * 0) + ( 0.16 *  v2)

v2 = 6.375 m/s

Explanation:

The answer is v2 = 6.375 m/s

(I did the equation and everything but just in case, check with someone else so you don't get the wrong answer)

Hence, the radio waves from KROQ have a wavelength of roughly 2.81 metres.

A radio wave's frequency is determined by dividing its velocity (c = 299 792 458 m/s, or the speed of light) by its wavelength. Wavelength is the length in metres of a single complete wave. In maths, frequency is defined as f = c/.

The frequency of radio waves is 106,700,000 Hz, while the speed of light  is roughly 300,000,000 m/s. The formula is as follows: c = fλ

where the wavelength is used.

When we rearrange this formula to account for, we obtain: λ = c / f

Inputting the values provided yields:

λ = 300,000,000 m/s / 106,700,000 Hz

λ ≈ 2.81 meters

To know more about wavelength visit:-

https://brainly.com/question/13676179

#SPJ1

The gravitational potential energy of the two climbers would be 26,460 J.

The gravitational potential energy (PE) of an object is given by the formula:

PE = mgh

where m is the mass of the object, g is the acceleration due to gravity, and h is the height of the object above some reference point.

In this case, the combined mass of the two climbers is 150 kg, and they are 18 m above the ground. Using g = 9.8 m/s², we can calculate their gravitational potential energy as:

PE = (150 kg) x (9.8 m/s²) x (18 m) = 26,460 J

Rounded to the nearest thousand, the gravitational potential energy of the two climbers is 26,000 J.

More on gravitational potential energy can be found here: https://brainly.com/question/19768887

#SPJ1

The pair of cities moving apart because of plate motion is London and Boston.

London and Boston are moving apart due to the motion of tectonic plates. The Earth's lithosphere is divided into several large plates that are in constant motion due to the underlying mantle convection. The movement of these plates is driven by the forces generated by the mantle convection, which causes the plates to move away from each other, move towards each other, or move sideways past each other.

London and Boston are located on separate tectonic plates that are moving away from each other. London is located on the Eurasian Plate, while Boston is located on the North American Plate.

Find out more on plate motion at https://brainly.com/question/18612190

#SPJ1

P = [M1 L1 T-2] × [L2]-1 = M1 L-1 T -2. Therefore, the pressure is dimensionally represented as M1 L-1 T -2.

The relationship of the wavelength of a particle and its mass is they are inversely related.

Option D is correct.

The link between a particle's mass and wavelength is provided by the de Broglie wavelength equation: = h/p,

where is the wavelength, h is the Planck constant, and p is the particle's momentum.

This condition shows that a molecule's energy is contrarily relative to its frequency. Because momentum (p = mv) is defined as the product of mass and velocity, we can also say that a particle's wavelength is inversely proportional to its mass.

A wavelength is the distance between two identical points (adjacent crests) in consecutive cycles of a waveform signal that travels in space or down a wire. In wireless systems, its length is typically measured in meters (m), centimeters (cm), or millimeters (mm).

To know more about Wavelength:

brainly.com/question/10750459

#SPJ1

Maria is taking the Rorschach inkblot test.

The test is designed to assess an individual's personality traits and psychological functioning based on their responses to the images.

The Rorschach inkblot test, which  uses a set of inkblot images and asks participants to describe what they see. The Rorschach test is a projective test that is often used to assess an individual's personality, emotional functioning, and thought processes.

Learn more about personality test:https://brainly.com/question/8789865

#SPJ1

While submerged in water (n = 1.33) for two convex lenses, the focal lengths of Lens 1 is 19.67 cm and Lens 2 is 18.9 cm.

Lens is a transparent device that is used to focus or redirect light, allowing it to be magnified, focused, or projected onto a surface. It is made of a curved, transparent material like glass, plastic, or crystal. Lenses are commonly used in eyeglasses, cameras, microscopes, and other optical devices. They can be used to magnify, reduce, or otherwise change the direction of light in order to produce a desired effect. They are also used in other applications such as laser cutting and welding, as well as medical imaging and laser treatments.

To learn more about Lens

https://brainly.com/question/28039799

#SPJ1

Answer:

last choice

Explanation:

With a single fixed pulley, you pull down (working with the force of gravity) to lift the load up.

To derive the equation for the buoyant force, we can start with the equation for the pressure from a fluid at a certain depth:

P = ρgh + Patm

where P is the pressure at a depth h, ρ is the density of the fluid, g is the acceleration due to gravity, and Patm is the atmospheric pressure at the surface of the fluid.

Now, let's consider a simple submerged object, such as a perfect cube with sides of length s, as the hint suggests. The object is fully submerged in the fluid, so it experiences a pressure difference between the top and bottom surfaces. The pressure at the top surface of the object is Ptop = ρghtop + Patm, where htop is the depth of the top surface below the surface of the fluid. The pressure at the bottom surface of the object is Pbottom = ρghbottom + Patm, where hbottom is the depth of the bottom surface below the surface of the fluid. Since the object is at rest in the fluid, the net force acting on the object must be zero. Therefore, the buoyant force must be equal and opposite to the weight of the object:

Buoyant force = Weight of object

The weight of the object is given by its mass multiplied by the acceleration due to gravity:

Weight of object = mg

where m is the mass of the object and g is the acceleration due to gravity.

To find the buoyant force, we need to find the difference between the pressure at the top and bottom surfaces of the object, and then multiply that difference by the surface area of the object:

Buoyant force = Pressure difference × Surface area

The pressure difference is given by:

Pressure difference = Pbottom - Ptop

= (ρghbottom + Patm) - (ρghtop + Patm)

= ρg(hbottom - htop)

Therefore, the buoyant force is:

Buoyant force = ρg(hbottom - htop) × Surface area

For a perfect cube with sides of length s, the surface area is given by A = 6s^2. Therefore, the buoyant force on the cube is:

Buoyant force = ρg(hbottom - htop) × 6s^2

This is the equation for the buoyant force on a submerged object, derived from the equation for the pressure from a fluid at a certain depth and the concept of the buoyant force being due to the pressure difference between the top and bottom of an object.

Answer:

if the temperature of the sink is lowered by 6.7%, the efficiency of the Carnot engine will increase by 10%.

Explanation:

The efficiency of a Carnot engine is given by the equation:

η = 1 - T_sink / T_source

where η is the efficiency, T_sink is the temperature of the sink, and T_source is the temperature of the source.

In this case, we are given that the efficiency of the engine is 40%. Therefore, we can write:

0.4 = 1 - T_sink / T_source

Rearranging this equation, we get:

T_sink / T_source = 1 - 0.4

T_sink / T_source = 0.6

Next, we are asked to find the temperature of the sink needed to increase the efficiency of the engine by 10%. Let's call this new efficiency η_new. Since the efficiency of a Carnot engine is given by the same equation as before, we can write:

η_new = 1 - T_sink_new / T_source

where η_new is the new efficiency, and T_sink_new is the new temperature of the sink.

We know that the new efficiency is 10% higher than the original efficiency, so we can write:

η_new = η + 0.1η = 0.4 + 0.1(0.4) = 0.44

Substituting this into the equation above, we get:

0.44 = 1 - T_sink_new / T_source

Rearranging this equation, we get:

T_sink_new / T_source = 1 - 0.44

T_sink_new / T_source = 0.56

Now we can set up an equation to find the new temperature of the sink:

0.56 = T_sink_new / T_source

T_sink_new = 0.56T_source

To find the temperature difference between the old and new sink temperatures, we can subtract the two equations we have derived:

T_sink_new - T_sink = 0.6T_source - 0.56T_source

T_sink_new - T_sink = 0.04T_source

Finally, we can substitute the given efficiency of 40% to find the source temperature:

0.4 = 1 - T_sink / T_source

T_source = T_sink / (1 - 0.4)

T_source = T_sink / 0.6

Substituting this expression for T_source into the equation for the temperature difference, we get:

T_sink_new - T_sink = 0.04(T_sink / 0.6)

Simplifying, we get:

T_sink_new - T_sink = 0.067T_sink

Multiplying both sides by 100, we get:

(T_sink_new - T_sink) * 100 = 6.7T_sink

Therefore, if the temperature of the sink is lowered by 6.7%, the efficiency of the Carnot engine will increase by 10%.

The force per unit length of Y would be 1.25 * [tex]10^{-3[/tex] N/m.

The force per unit length between two parallel wires carrying currents can be calculated using the equation:

F = μ0 * I1 * I2 * L / (2 * π * d)

where:

Substituting the given values, we get:

F_X = μ0 * 3A * 5A * L / (2 * π * d) = 5 * 10^-5 N

Solving for F_Y, we get:

F_Y = 2 * F_X * π * d / (μ0 * 5A * L)

= 2 * (5 * 10^-5 N) * π * d / (4π * 10^-7 T·m/A * 5A * L)

= 1.25 * [tex]10^{-3[/tex] N/m

Therefore, the force per unit length experienced by wire Y is 1.25 * 10^-3 N/m.

More on force per unit length can be found here: https://brainly.com/question/20358392

#SPJ1

The magnitude of the normal force of the car is given by Fn = Fg cotθ.

The normal force is the force exerted by the racetrack perpendicular to the car's motion. Let's now derive the expression for the magnitude of the normal force of the car:

The perpendicular component of the normal force is given by:

Fn⊥ = Fg cosθ

The parallel component of the normal force provides the centripetal force required for circular motion.

The centripetal force (Fc) is given by:

Fc = mv²/r

where;

The centripetal force can also be expressed in terms of the parallel component of the normal force:

Fc = Fn∥ = Fn sinθ

Equating the two expressions for Fc, we get:

Fn sinθ = mv²/r

Solving for Fn, we get:

Fn = mv²/(r sinθ)

Substituting the expression for Fg cosθ, we get:

Fn = Fg cosθ / sinθ

or

Fn = Fg cotθ

where;

Learn more about normal force here: https://brainly.com/question/14486416

#SPJ1

The complete question is below:

Circular turns of radius r in a racetrack are often banked at an angle θ to allow the cars to achieve higher speeds around the turns. Assume friction is not present.

Now write the magnitude of the normal force of the car, in terms of the gravitational force Fg, g, θ, the radius of the track r, and the velocity that the car is traveling v.

A typical 16-line poem that described centripetal force can be found below.

In circular motion, a force we call,

Centripetal, it keeps things in thrall.

Directed towards the center of the path,

Without it, objects would face a wrath.

Angular velocity is key,

The rate of change of the angle we see.

And the radius of the circle too,

Both play a role in what we must do.

The mass of the object cannot be ignored,

It factors in with gravity's cord.

As the force pulls towards the center,

Centripetal force is what we enter.

It is the sum of all the forces in play,

Equal to mass times velocity squared, we say.

And if the force is too weak or too strong,

Off the circular path, the object goes wrong.

Thus, centripetal force is what we need,

To keep objects moving at the speed,

In a circular path, they're meant to be,

A force that keeps them in harmony.

More on centripetal force can be found here: https://brainly.com/question/11324711

#SPJ1