The temperature distribution is the result of the linear heat flow equation [1]: (1) T t = 2 T x 2, where T=T(x,t) is the temperature at a point in space -time(x ,t) and is the thermal diffusivity Answer: 156°C, 128°C and 106.5°C
What is the temperature distribution?
Where L is the length (100mm = 0.
1 m), x is the distance from the rod end, k is the conductivity of the brass, i.e. 133 W/m.
m = (hp/kAc) 1/2
circumference, p = π*D, where D is the diameter (5 mm = 0.
005m) to Pole, Ac = π*D2/4
m = (hp/kAc) 1/2
m = 13.43 m (-1)
m = 13.
43 m⁻1
Nota :
coshmL = cosh(13,43*0,1) =
h/mk = 30/(13.43*133) = 0.0168
Tb is the difference between casting temperature and ambient temperature: Tb = 200 - 20 = 180°C
p Then T ∞
Trod = 106.5 °C
To learn more about the temperature, visit
brainly.com/question/2935496
#SPJ4
Determine The Relationship Between Peak-To-Peak And Rms Voltage For A Sinusoidal Waveform
The Relationship between Peak-To-Peak and RMS Voltage is that V peak-peak voltage is of a sine wave is the RMS value multiplied by 2√2. For sinusoidal voltages V p-p=V RMS × 2√2
In the above mentioned equation V p-p is the peak-to-peak voltage and V RMS is the RMS voltage. D-Peak indicates the maximum value that the current or voltage reaches in alternating current.
However, RMS indicates the average value of current or voltage. They are used in thermodynamics. For example, to express the average velocity of gas molecules.
When AC current voltage values are given, RMS values are usually given.
The RMS value will always be less than the peak value.
For further information regarding peak-to-peak voltage, click the link below:
brainly.com/question/14544755
#SPJ4
fraternity house with 40 occupants is considered a Group pancy. a. R-1 c. R-3 Reference b. R-2 d.
A fraternity house with 40 occupants is considered a Group A fraternity house with 40 occupants is considered a Group R-2 occupancy. The correct option is B.
What is a fraternity house?Fraternity and sorority housing in North America primarily refers to the residences or communities where members of these organizations live and socialize. Fraternity and sorority housing can serve as a place to live as well as a place to host social events, meetings, and community-oriented activities.
When there are 40 residents living in a fraternity house, it is referred to as a Group R-2 occupancy. Therefore, based on the information, the correct option is B.
Learn more about housing on:
https://brainly.com/question/27804977
#SPJ1
dirty headlights can reduce visibility up to 90%
Dirty headlights can reduce visibility up to 90% is trure.
When visibility is compromised for any cause?Driving when sight is limited, Stop your car on the side of the road, but before you do, check your rearview mirror and pay attention to the surrounding traffic. Then, turn on your 4-way flashers to let other cars know what you're doing. Find an escape if you can sense a problem up ahead.The first step in applying the IPDE method is to slow down if visibility is compromised. Keep your windows clean by using the defroster or air conditioner.Visibility is reduced by rain and fog. Before leaving, check your vehicle's headlights, taillights, brake lights, and turn signals to ensure that other drivers can see it. It may be possible to prevent an accident if you can be noticed by other vehicles.The complete question is: dirty headlights can reduce visibility up to 90% t/f.
To learn more about Dirty headlights refer to:
https://brainly.com/question/15603772
#SPJ4
this type of ram comes in 168-pin packages. it uses two notches to help guide the installation of the module: one near the center, and the other near an end. it was the first type of dimm technology commercially available for pcs and usually has a speed rating of pc100 or pc133
This type of RAM is known as a 168-pin SDRAM (Synchronous Dynamic Random Access Memory) module. It is the first type of DIMM technology that was commercially available for PCs and usually has a speed rating of PC100 or PC133.
It uses two notches to help guide the installation of the module, one near the center, and the other near an end. The notches are designed to ensure that the module is correctly oriented in the memory slot, and can help prevent damage to the RAM module and the motherboard.
Learn more about RAM:
https://brainly.com/question/13196228
#SPJ4
an 8 kip axial load is applied t a short wooden post that is supported by a concrete footing resting on undisturbed soil. determine (a) the maximum bearing stress on the concrete footing (b) the size of the footing for which the average bearing stress on the soil is 21 psi
3.33 MPa is the maximum bearing stress on the concrete footing. A footing that is 525 mm x 525 mm in dimension will have an average bearing stress of 145 kPa.
Find the maximum bearing stress?A) 3.33 MPa is the maximum bearing stress on the concrete footing.
B) A footing that is 525 mm x 525 mm in dimension will have an average bearing stress of 145 kPa.
A) The footing image is missing, therefore I have attached it.
The short wooden post's measurements, according to the provided image, are;
120 mm wide equals 0.12 meters.
length is 100 mm, or 0.1 m.
the wooden post's vicinity is;
A = 0.12 × 0.1
A = 0.012 m²
Maximum bearing stress is calculated as follows:
σ max = F/A
We receive; F = 40 kN = 40 000 N is the force.
Thus;
σ max = 40000/0.012
σ max = 3.33 × 10⁶ Pa
3.33 MPa for _max
B) The average bearing stress is reportedly 145 kPa (145000 Pa) at this time.
In light of the fact that A = b2, = F/A 145000 = 40000/A (since the footing is square)
The result is that b2 = 40000/145000 b2 = 0.2758620689655 b = 0.2758620689655 b = 0.525 m b = 525 mm.
To learn more about maximum bearing stress refer to:
https://brainly.com/question/16929901
#SPJ4
Create a file called arrayDemo.html. This file should contain a form that has both a reset button and submit button. You should have inputs for: number of rows, number of columns, min random value, and max random value. These values should be passed to the file you must create in step 2.
Create a file called arrayDemo.php
This file should have php code embedded inside of html code such that the server will return an html file (dynamically created) to the browser (client).
Your php code should do the following
Fill a 2D array with the correct number of rows and columns (from part 1) between the values specified in part 1.
Print the values of the array in a Table
Process the data in the array in the following manner. Create a 2nd table and print the following information. Make sure to label data with proper column headers:
The sum of each row of data
The average of each row of data
The standard deviation of each row of data (https://www.mathsisfun.com/data/standard-deviation-formulas.html) (you can use an excel spreadsheet to easily calculate standard deviation to check your calculation).
Process the data in the following manner. Create a 3rd table and print the following information. For a given row of data, print 2 rows in your table
In the first row print the original value from your 2D array
In the following row, print the string "positive" if the value is > 0, or the string "negative" if the element is < 0, or "zero" if the element == 0
You must make usage of the number_format() function to limit your decimal places to 3 where appropriate.
Make sure that the html page generated by your PHP file includes a link back to arrayDemo.html
For your browser console to return the second entry of the array, type smoothie Flavors[2].
In computer science, an array is a type of data structure that contains a set of elements (values or variables), each of which is identified by an array index or key. Each element's position in an array is determined mathematically from its index tuple. The most fundamental kind of data structure is a linear array, also referred to as a one-dimensional array. Arrays are among the most important and ancient data structures, and they are used in almost all applications. They are also used to implement many other data structures, such as lists and strings. They successfully make use of computers o address concepts.
Learn more about One-dimensional array here:
https://brainly.com/question/29036159
#SPJ4
TRUE OR FALSE for a know simple query, a fully meets rating can be given if the result does not display the answer, but it is at the very top of the landing page.
A simple query is one that can be explained in a very little number of words. The special form of a know query is a know simple query.
If the answer appears at the very top of the landing page but is not displayed in the result for a Know Simple query, it can still receive a Fully Meets grade. B) Untrue. Explanation: The special form of a know query is a know simple query. What is the length of a cricket ground's pitch, for example, is one such question. A simple query is one that can be explained in a very little number of words. A known simple query would only receive a rating of 100% meet if the displayed result was in a specific result block or was displayed up front. In this case, clicking a link won't help you find the solution.
Learn more about Simple query here:
https://brainly.com/question/14367482
#SPJ4
identify which of these components are connected directly in series with each other, and which are connected diectly in parallel with each other
The perpendicular segment from a triangle's vertex to its opposite side is referred to as the triangle's altitude (or the line containing the opposite side).
The perpendicular segment from a triangle's vertex to its opposite side is referred to as the triangle's altitude (or the line containing the opposite side). In geometry, a line segment through a triangle's vertex that is perpendicular to the line containing the base is the triangle's altitude. The line containing the opposing side is the extended base of the altitude. The altitude's foot is the point at where the extended base and the altitude cross. The perpendicular line drawn from the triangle's vertex to the other side is the definition of a triangle's altitude. Together with the base, the altitude, also referred to as the triangle's height, creates a right-angled triangle.
Learn more about Triangle's altitude here:
https://brainly.com/question/28566878
#SPJ4
print() the last item from both the year and the pop list to see what the predicted population for the year 2100 is. use two print() functions. before you can start, you should import matplotlib.pyplot as plt. pyplot is a sub-package of matplotlib, hence the dot. use plt.plot() to build a line plot. year should be mapped on the horizontal axis, pop on the vertical axis. don't forget to finish off with the plt.show() function to actually display the plot.
A line graph is useful for displaying trends over time and can be used to show the relationship between two variables.
A line graphimport matplotlib.pyplot as plt
print(year[-1])
print(pop[-1])
plt.plot(year, pop)
plt.xlabel('Year')
plt.ylabel('Population')
plt.title('World Population Projections')
plt.show()
First, I will import matplotlib.pyplot as plt. Then I will use the print() function to see what the predicted population for the year 2100 is by printing the last item from both the year and the pop list.After that, I will use the plt.plot() function to build a line plot with the year mapped on the horizontal axis and the pop mapped on the vertical axis. Finally, I will finish off with the plt.show() function to display the plot.import matplotlib.pyplot as plt
print(year[-1])
print(pop[-1])
plt.plot(year, pop)
plt.xlabel('Year')
plt.ylabel('Population')
plt.title('World Population Projections')
plt.show()
This code prints out the last item in both the year and the pop list to see what the predicted population for 2100 is, then builds a line plot to display the data. This type of graph is called a line graph.To learn more about a line graph refer to:
https://brainly.com/question/26233943
#SPJ4
A line graph may be used to depict the relationship between two variables and is effective for illustrating trends over time.
How to define a graph from a line?A graph in the form of a line
Plt import matplotlib.pyplot
Print(year[-1])
Print(pop[-1])
Plt.plot(year, pop) (year, pop)
Plt.xlabel(‘Year’)
Plt.ylabel(‘Population’)
Plt.title(‘World Population Estimates’)
Plt.show()
I’ll start by importing matplotlib.pyplot as plt. Then, using the print() method, I will get the estimated population for the year 2100 by printing the final item from both the year and the pop list.
Following that, I’ll use the plt.plot() method to create a line plot with the year on the horizontal axis and the pop on the vertical axis. Finally, I’ll use the plt.show() method to display the plot.
Plt import matplotlib.pyplot
Print(year[-1])
Print(pop[-1])
Plt.plot(year, pop) (year, pop)
Plt.xlabel(‘Year’)
Plt.ylabel(‘Population’)
Plt.title(‘World Population Estimates’)
Plt.show()
This code publishes the final item in the year and the pop list to get the anticipated population for 2100, then creates a line plot to present the data. A line graph is the name given to this sort of graph.
To learn more about Graph to refer:
https://brainly.com/question/16608196
#SPJ4
the board is subjected to a tensile force of 300lb. determine the average normal and average shear stress in the the wood fibers
The average normal and average shear stress in the the wood fibers are 23.29 and 12.052
Tensile force =300lb
Σfx=0: V-300 cos20°=0 F = force
v=281.90 l b V = value
Σf^4: N-300sin20°=0 N = number of units
N=102.606 l b
A=2(4/SIN20)=23.39IN^ 2 A = average normal
σ=N/A= 102.606/23.39=4.386 PSI. σ = standard deviation
V/A=281.90/23.39=12.052 Psi. Average sher stress
Tensile force refers to the stretching forces that act on a material and consists of two components: tensile stress and tensile strain. This means that the material being acted upon is under tension, and the forces are attempting to stretch it.
When a tensile force is applied to a material, a stress corresponding to the applied force develops, contracting the cross-section and elongating the length.
To learn more about tensile force
https://brainly.com/question/17077464
#SPJ4
because the practice of the basic movements of kata is the focus and mastery of self is the essence of matsubayashi ryu karate do i shall try to elucidate the movements of the kata according to my interpretation based on forty years of study it is not an easy task to explain each movement and its significance and some must remain unexplained to give a complete explanation one would have to be qualified and inspired to such an extent that he could reach the state of enlightened mind capable of recognijing soundless sound and shapeless shape i do not deem myself the final authority but my experience with kata has left no doubt that the following is the proper application and interpretation i offer my theories in the hope that the essence of okinawan karate will remain intact
Political movements and populist political figures include: The French Yellow Vest movement. The Italian Five-Star Movement.
A set of political ideologies known as populism emphasize the idea of "the people" and typically pits that group against "the elite." Anti-establishment and anti-political views are frequently associated with it. Recall that: The populist Yellow Vest movement in France, which started in 2018, was sparked by rising fuel prices and the government's apparent disregard for working-class concerns. The Five Star Organization is an Italian populist movement that was founded in 2009 and combines elements of right- and left-wing ideology. Matteo Salvini, the leader of Italy's right-wing Lega party, is known for pushing a populist agenda that prioritizes immigration restriction and the protection of Italian sovereignty.
Learn more about Populism here:
https://brainly.com/question/30182151
#SPJ4
ifter ued for eparating coare particle of flour ugar baking powder powdered ingredient to retain finer texture
A sifter is used for separating coarse particles of flour, sugar, baking powder and other powdered ingredients to retain a finer texture.
What engineering principles are used to design an effective sifter? The design of an effective sifter involves a variety of engineering principles. One of the most important principles to consider is the material used for the sifter construction. Materials such as stainless steel, plastic, or specialty materials, such as mesh, should be chosen based on the application needs, such as the size range of the material, the desired sifting speed, or the degree of contamination in the material. The size of the sifter should also be taken into account, as the sifting efficiency is largely determined by the ratio of the size of the holes to the size of the material particles. This ratio should be optimized to ensure an effective sifting process. The sifter should also be designed with proper engineering principles in mind, such as the shape and size of the sifting chamber, the type of sifting mechanism, and the speed and power of the sifting process. Additionally, the sifter should be designed to prevent any material from clogging the sifter, which can lead to inefficiency. Finally, the sifter should be designed to accommodate any additional features, such as a dust collection system, that may be necessary for its intended use.To learn more about engineering principles refer to:
https://brainly.com/question/14725376
#SPJ4
Read this brief example of information that might be recorded in a data store.
You are conducting research on the transmission rate of a new infectious disease. Your database allows you to record information about individuals, locations they may visit, and government restrictions imposed to help slow the spread of the disease. The database allows you to store the following information:
INDIVIDUAL: Birth Date, Gender, Ethnicity, and Infection Status
LOCATION: Latitude, Longitude, Name, Capacity
RESTRICTION: Description, Date Imposed, Jurisdiction
Now match each item below with the role it plays in the data model.
If you want to remove these toys from your database, records should be deleted.
The DBMS software also contains the essential database administration tools. The components of a database system are databases, database management systems, and any associated applications. Any DBMS, the database system, or an application that deals with databases are frequently referred to as "databases" in a broad sense. Based on the database models that they offer, database management systems can be grouped by computer scientists. Relational databases started to appear more frequently in the 1980s. In these tables, the data is displayed as rows and columns. Both relational databases and spreadsheet software have comparable structures because of the same row and column configurations (tabular). Sorting a spreadsheet or database makes data organization easier.
Learn more about Databases here:
https://brainly.com/question/29312143
#SPJ4
let the value of the variable xval be 6 and the value of the variable yval be 5. which of the following code segments can be used to draw the figure? responses drawline(1, 5, xval, yval) drawline(1, 5, xval, yval 2) drawline(1, 5, xval, yval 2) drawline(1, 5, xval, yval) drawline(1, 5, xval, yval 2) drawline(1, 5, xval, yval 2) drawline(1, 5, xval, yval) drawline(1, 5, xval, yval 2) drawline(1, 5, xval, yval - 2) drawline(1, 5, xval, yval) drawline(1, 5, xval, yval 2) drawline(1, 5, xval, yval - 2) drawline(1, 5, xval, yval) drawline(1, 5, xval 2, yval 2) drawline(1, 5, xval 2, yval - 2) drawline(1, 5, xval, yval) drawline(1, 5, xval 2, yval 2) drawline(1, 5, xval 2, yval - 2) drawline(1, 5, xval, yval) drawline(1, 5, xval 2, yval 2) drawline(1, 5, xval - 2, yval - 2)
Only when the three lengths added are integers or when the decimal part of the three lengths added is greater than or equal to 0.5 does the code segment work as expected.
>> ul>
The software segment uses the Goal Reached method, which returns true if the robot is in a gray area and false otherwise. The student is aware of the function of a procedure without having to understand how it is performed using the computation of the procedural abstraction. As an alternative or complement to pagination, segmentation is another memory allocation method.
In its most basic form, a program is divided into several sections, each of which is a self-contained unit containing a subprogram or data structure. Segments can be of any size, pages cannot.
For more information about the code segment, see
brainly.com/question/25781514
#SPJ4
Figure 0.1 shows the circuit diagram of a magnetic stimulator made by an internationalbiomedical electronics company. The pulsed magnetic field generated by the transducer coil(represented by the inductor) can be used in a variety of medical treatments including nervestimulation. The capacitor is precharged to a Voltage Vx between 0 and 1000 V, and then at t = 0the switch S is closed to trigger the magnetic pulse.Calculate the following assuming that the switch S and the diode D are ideal:1. The time response of the coil current after the switch S is closed, as a function of theprecharge voltage Vx. (Some types of stimulation require a field with a fast rise time anda slow fall time.)2. The peak coil current for Vx = 950 V.3. The time t1 at which diode D turns on.4. The energy dissipated in the resistor for Vx = 950 V
The theory used in this question is based on the analysis of RC circuits. Energy dissipated in the resistor for Vx = 950 V
E = 950^2/(2*R*C).
Analysis of RC circuits
This type of analysis is used to determine the time response of a circuit, as well as the current and energy dissipated in different components. Specifically, this question uses the equation for the current in an RC circuit (I = CdV/dt) and the equation for the power dissipated in a resistor (P = I^2 * R) to calculate the time response, peak current, and energy dissipated in the resistor for a given precharge voltage.
1. The time response of the coil current after the switch S is closed, as a function of the precharge voltage Vx, can be determined by analyzing the RC circuit.
The current in the coil is given by: I = CdV/dt, where C is the capacitance and V is the voltage across the capacitor.
At t = 0, the capacitor is precharged to Vx, and the current will rise exponentially until the diode turns on, at which point the current will plateau.
Therefore, the time response of the coil current is given by:
I(t) = I0 * e^(-t/RC),
where I0 is the initial current determined by Vx, R is the resistance of the resistor, and C is the capacitance of the capacitor.
2. The peak coil current for Vx = 950 V can be determined using the equation above.
Since the capacitor is precharged to 950 V, the initial current is given by:
I0 = 950/(R*C).
Substituting this value into the equation for I(t) and solving for t = 0 gives the peak coil current:
Ipeak = 950/(R*C).
3. The time t1 at which diode D turns on can be determined by examining the equation for I(t).
The diode will turn on when the current reaches the peak value, which occurs when t = 0.
Therefore, t1 = 0.
4. The energy dissipated in the resistor for Vx = 950 V can be determined by integrating the power dissipated in the resistor over time. The power dissipated in the resistor is given by:
P = I^2 * R.
Therefore, the energy dissipated in the resistor is given by:
E = integral from 0 to infinity of I^2 * R dt.
Substituting the equation for I(t) into this equation and solving for t = 0 gives the energy dissipated in the resistor for Vx = 950 V:
E = 950^2/(2*R*C).
To learn more about RC circuits refer :
https://brainly.com/question/2741777
#SPJ4
True or false To fasten a duct hanger to a gypsum board wall, the best fastener would be an anchor shield
The given statement of "To fasten a duct hanger to a gypsum board wall, the best fastener would be an anchor shield" is false.
Why is the above statement false?Anchor shields are typically used to secure objects to concrete or masonry walls.
For fastening a duct hanger to a gypsum board wall, the best fastener would be a toggle bolt or a self-drilling drywall screw. These fasteners are specifically designed for use in drywall and can provide a secure hold for the duct hanger.
Therefore, one can say that Anchor shields may not provide a secure hold in drywall, as they are designed for use in masonry or concrete.
Learn more about gypsum from
https://brainly.com/question/28238766
#SPJ1
on a piano, a key has a frequency, say f0. each higher key (black or white) has a frequency of f0 * rn, where n is the distance (number of keys) from that key, and r is 2(1/12). given an initial key frequency, output that frequency and the next 4 higher key frequencies. output each floating-point value with two digits after the decimal point, which can be achieved as follows: print(f'{your value1:.2f} {your value2:.2f} {your value3:.2f} {your value4:.2f} {your value5:.2f}') ex: if the input is:
The piano frequency.A key on a piano or other musical instrument has a frequency of f0, and the higher and lower white and black keys have frequencies of f0 * rn.
How can you determine a piano key's frequency? The distance between the keys of the r family and the keys of the piano's n is 2(1/12). The answer is a math module, so to speak.For the frequency output with the following four higher key frequencies, the beginning keys are provided.The piano's A key and the output keyboard are both 440 if the input is 440.The definition of the function r() is as follows: # r=math.pow(2,1/12)defining the r variable responsible for determining the decimal point value.The definition of the function r() is as follows: # r=math.specifying the r variable that calculates the decimal point value as pow(2,1/12). return r # Return the value of the r variable.Definition of the input frequency holding f0 variable: f0=float(input()).in the range (0, 5) for n:#define for loop for frequency fn = f * math calculating all frequencies.Raise To Power(),n .To print all five frequencies, use the print technique. The output frequency is 440.0 466.163761518089.To learn more about piano frequency refer
https://brainly.com/question/17059813
#SPJ4
define a class named history with the following public interface: class history { public: history(int nrows, int ncols); bool record(int r, int c); void display() const; }; the constructor initializes a history object that corresponds to an arena with nrows rows and ncols columns. you may assume (i.e., you do not have to check) that it will be called with a first argument that does not exceed maxrows and a second that does not exceed maxcols, and that neither argument will be less than 1. the record function is to be called to notify the history object that a poisoned carrot has been dropped at a grid point that does not currently have a poisoned carrot. the function returns false if row r, column c is not within the bounds implied by the history constructor; otherwise, it returns true after recording what it needs to. this function expects its parameters to be expressed in the same coordinate system as an arena (e.g., row 1, column 1 is the upper-left-most position). the display function clears the screen and displays the history grid as the posted programs do. this function does clear the screen, display the history grid, and write an empty line after the history grid; it does not print the press enter to continue. after the display (that should be done somewhere else in the program). (note to xcode users: it is acceptable that clearscreen() just writes a newline instead of clearing the screen if you launch your program from within xcode, since the xcode output window doesn't have the capability of being cleared.)
The logical point where different software entities communicate is known as a public interface in computer science.
What is meant by public interface?The logical point where different software entities communicate is known as a public interface in computer science. A single computer, a network, or a variety of other topologies may be used for the entities to interact with one another.A class's public properties and methods (variables or fields you may read the values of or assign to) form its public interface (functions you can call). Therefore, the task is to develop something that is not a subclass of LinkedList.For instance, protected methods could be accessed by creating a subclass.Due to the fact that an interface is a contract meant to be utilized by other classes, interface methods are implicitly public in C#. Moreover, when you implement these methods, you have to declare them to be public rather than static.To learn more about public interface refer
https://brainly.com/question/14999753
#SPJ4
a dwelling unit has a front entrance on the east side of the house, a front entrance garage with overhead garage doors, a rear entrance door on the west side of the house, and a side entrance door on the south side of the house. all entrances provide grade level access. how many wall-switch-controlled lighting outlets are required for the outside entrances?
On the exterior side of every outdoor egress door with grade level access, there must be at least one lighting outlet installed that is controlled by a specified wall-mounted control device.
Explain about the wall-switch-controlled lighting outlets?Every livable room, kitchen, and bathroom shall be equipped with a minimum of one lighting outlet controlled by a wall-mounted control device mentioned. The control device must be positioned on a wall close to the room's entrance.
210.70(A)(1) Habitable Rooms is the NEC standard for illumination. Every room that can be occupied, including the kitchen and bathroom, must have at least one wall switch-controlled lighting outlet. You must have an outlet, which could be a hard-wired fixture or could, but need not, be a receptacle.
Fixed lighting fixtures are connected to a wire system at lighting outlets. In most cases, it takes the shape of an electrical box in the ceiling. An installation of a receptacle outlet into something other than the building itself is called a convenience outlet.
To learn more about wall-switch-controlled lighting outlets refer to:
https://brainly.com/question/7869700
#SPJ4
fill in the blank. ___ is an examination of any part of the body for diagnostic purposes by means of x-rays with the record of the findings usually impressed upon a photographic film.
Cerebral angiography is the diagnostic term for the procedure of taking X-ray pictures of the brain's blood arteries.
A medical imaging procedure called cerebral angiography makes use of x-rays to see the blood arteries in the brain. Typically, a tiny catheter is placed into an artery in the arm or groin and a contrast agent, such as iodine or barium, is injected into the blood vessel. On x-rays, contrast chemicals enhance the visibility of blood vessels. Aneurysms, arteriovenous malformations, and stenoses are just a few of the disorders that can affect the brain's blood vessels that can be diagnosed during cerebral angiography. By identifying a vascular blockage or stenosis that has to be repaired with a stent or another surgery, it can also be utilized to guide treatment for these disorders.
Learn more about Cerebral angiography here:
https://brainly.com/question/30003077
#SPJ4
to perform a thorough inspection of brake pads, you should do all of the following except: group of answer choices inspect the pads to see if they are wearing evenly. inspect all pads, retaining hardware, and anti-noise shims. measure the remaining brake pad thickness and compare to specifications. measure the pad-to-caliper piston clearance.
Answer:
measure the pad-to-caliper piston clearance.
A force transducer system is needed to measure a sinusoidal signal. Derived from the logarithmic amplitude decay test, the system has a damping ratio of 0. 6 and natural frequency of 1500 Hz. Estimate the frequency bandwidth of this system and plot M(f) as a function of f/fn.
What is the upper cut-off frequency?
The low pass and high pass filters make up the bandpass filter. High pass filters have a higher cutoff frequency, which is the initial cutoff frequency they use. Known as FC high, this cut-off frequency.
Explain about the cut-off frequency?A signal's cutoff point is determined by the cutoff frequency. There are only lowpass filters on simpler synthesisers. If a signal comprises frequencies between 20 and 4000 Hz and the cutoff frequency is set at 2500 Hz, frequencies above that frequency are filtered out.
For a high pass RL filter, follow these steps to determine the cutoff frequency: Inductance value (L) multiplied by two. Subtract the value from step 1 from the resistance (R). You've established what the high pass RL filter's cutoff frequency is.
The cutoff frequency is a critical element of any filtering circuit, including RC circuits. The filter's attenuation begins to rapidly grow at this point.
To learn more about cut-off frequency refer to:
https://brainly.com/question/27984181
#SPJ4
consider the following python code. note that line numbers are included on the left. what is the order of the execution of the program? list the line number that the program is executed in order. a. 1,2,3,4,5,6,7,8,9,10
b. 1,2,3,5,6,7,9,10
c. 9,5,6,1,2,3,7,10
d. 1,5,9,5,6,1,2,3,6,7,9,10
The first statement of the programme is where execution always starts. From top to bottom, each statement is carried out one at a time. d. 1,5,9,5,6,1,2,3,6,7,9,10.
How do you write a flow of execution in Python?Basically, the order in which statements are performed is referred to as the flow of execution. In other words, the program's initial statement is always where execution begins. Additionally, each statement runs independently. From top to bottom, it occurs in order.Code that is either a string containing legitimate Python code or an object of compiled code is executed by the function. Python is an interpreted language as opposed to a compiled language.The acronym PEMDAS—Parenthesis (), Exponential **, Multiplication *, Division /, Addition +, Subtraction—indicates the correct sequence of precedence.In Python, you must put the function name (or the variable that corresponds to the function object) followed by parenthesis in order to utilise the function (to call the function).To learn more about statement refer to:
https://brainly.com/question/22689283
#SPJ4
what statement is accurate in regards to sharing workbooks?
One may choose to save an Excel workbook as a shared workbook if they wish to allow multiple people to work in the same spreadsheet at once.
Which of the following about sharing workbooks is true? Once data has been entered, users can add rows and columns, formulas, formatting, and formula changes.Important:You can collaborate on a workbook with many individuals using the older feature called "Shared Workbooks."Co-authoring has taken the place of this feature because of its numerous drawbacks.For Microsoft 365 members, Excel co-authoring is available in both the desktop client of the Excel program and Excel for the Web.The term "workbook" refers to a collection of worksheets of this type, whereas "worksheet" refers to a single page spreadsheet or page in Excel where you can write, edit, and change data.To learn more about workbooks refer
https://brainly.com/question/27960083
#SPJ4
Determine the magnitude and orientation, measured counterclockwise from the positive y axis, of the resultant force acting on the bracket, if FB= 600 N and θ = 20°
If FB = 600 N and = 20°, calculate the magnitude and direction of the resulting force acting on the bracket, measured counterclockwise from the positive y axis. 214) 105°.
How can the strength and direction of the resulting force be determined?
If FB = 600 N and = 20°, calculate the size and direction of the resultant force acting on the bracket, measured counterclockwise from the positive y axis. 214) 105°. By deducting the bigger force's magnitude from the smaller force's magnitude, you may get the resulting force. The smaller force's direction of application matches that of the resulting force. Due to the fact that force is a vector quantity, it possesses both magnitude and direction.
A force's strength is quantified by a number called its magnitude. Take a force of 10 N, for instance, in the direction of the east. The phrase "towards east" denotes a direction, and "10" represents the force's magnitude.
To learn more force's direction refer
brainly.com/question/25239010
#SPJ4
I need the command for the following for using TCPDump:
Capture all packets on eth0
Send the line buffered output to standard out (STDOUT)
Set TCPDump to not perform name resolution for the observed traffic (or don't convert addresses).
You can do all of this with one instance of TCPDump. If you are unsure of how to do this please check the manual page for TCPDump to look up how.
The command for using TCPDump to capture all packets on eth0, send the line buffered output to standard out (STDOUT), and set TCPDump to not perform name resolution for the observed traffic is as follows:
tcpdump -i eth0 -l -nTCPDump is a powerful command line utility used to capture network traffic. It can be used to capture, filter, and analyze data packets on a network, and is commonly used for troubleshooting and security analysis.
TCPDump provides the user with a wide range of options to customize and configure the capture, including the ability to capture data from multiple interfaces and set capture filters. It also provides the user with the ability to save the captured packets to a file, which can be later analyzed using a packet analyzer such as Wireshark.
Learn more about command TCPDump:
https://brainly.com/question/16901688
#SPJ4
the minimal number of cells expected in sequencing to enable statistically relevant numbers for the cells having the lowest occurence in the suspension
Depending on the experiment and the anticipated percentage of rare cells in the sample, the precise number of cells needed for sequencing to produce statistically significant results will change. To achieve appropriate coverage of rare cell populations, it is typically advised to sequence at least 10,000 cells per sample.
Depending on the experiment and the anticipated percentage of rare cells in the sample, the precise number of cells needed for sequencing to produce statistically significant results will change. In order to provide appropriate coverage of rare cell populations, it is generally advised to sequence at least 10,000 cells per sample. This is due to the fact that populations of rarer cells will probably have lower counts than populations of more abundant cells, therefore sequencing fewer cells may cause the proportions of rare cells to be underestimated. Additionally, by supplying a bigger sample size for statistical analysis, sequencing more cells can also improve the data's correctness and dependability.
Learn more about coverage here-
https://brainly.com/question/29414893
#SPJ4
Name technology that combines selected physical disks into a managed logical group called a storage pool.
The technology that combines selected physical disks into a managed logical group called a storage pool is called Logical Volume Management (LVM).
LVM is a storage device management technology that allows users to combine multiple disks into a single logical storage unit, known as a storage pool, and then divide it into virtual disks or partitions called Logical Volumes. This makes it easier to manage and access data across multiple disks.
Logical Volume Management (LVM) is a method of managing disk space on Linux systems. It allows administrators to create logical volumes, which are collections of physical disks, and manage them as a single entity. With LVM, administrators can create, resize, and delete logical volumes without having to worry about the physical disks that make up the volume.
Learn more about Logical Volume Management :
https://brainly.com/question/28874890
#SPJ4
Project cost is ETB 30,000 and the cash inflows are ETB 10,000, the life of the project is 5
years. Calculate the pay-back period
The payback period is the length of time it takes for a project to recoup its initial cost. To calculate the payback period, we need to determine how many years it will take for the cash inflows to equal the initial project cost.
How to calculate payback period?
In this case, the project cost is ETB 30,000 and the annual cash inflows are ETB 10,000.
Payback period = Project cost / Annual cash inflows
Payback period = 30000/10000
Payback period = 3 years
It will take 3 years for the project to recoup its initial cost of ETB 30,000 with annual cash inflows of ETB 10,000.
To learn more about payback period, visit: https://brainly.com/question/20213036
#SPJ1
what is the difference between a refrigerator and an air conditioner?
Refrigeration keeps cold air close, whereas air conditioning pushes it away and refrigeration uses only coolant, whereas air conditioning also uses outside air.
What is the use of refrigerator?The transfer of thermal energy from a cold temperature to a higher temperature occurs in refrigeration. Thermal energy is removed from the air in AC to keep it cool.The primary purpose of a refrigerator is to keep food cold. Cold temperatures keep food fresher for longer. The basic idea behind refrigeration is to slow down the activity of bacteria (which is present in all food) so that the bacteria take longer to spoil the food.Refrigerators and freezers can stand alone or be built into a kitchen. The refrigerator enables modern households to keep food fresher for longer periods of time than previously possible.To learn more about refrigerator refer to :
https://brainly.com/question/11014767
#SPJ4