For FM modulation, the in-phase and quadrature components can be determined by differentiating the phase of the modulating signal with respect to time. The envelope can be determined by taking the absolute value of the modulated signal, and the phase can be determined by taking the phase angle of the modulated signal.
For PM modulation, the in-phase and quadrature components can be determined by integrating the phase of the modulating signal with respect to time. The envelope can be determined by taking the absolute value of the modulated signal, and the phase can be determined by taking the phase angle of the modulated signal.
To learn more about PM FM modulation :
https://brainly.com/question/30035950
#SPJ11
Examine the following Entity and decide which rule of Normal Form is being violated:
ENTITY: CLIENT
ATTRIBUTES:
# CLIENT ID
FIRST NAME
LAST NAME
STREET
CITY
ZIP CODE
The question at hand is: Examine the following Entity and decide which rule of Normal Form is being violated:
ENTITY: CLIENTATTRIBUTES:# CLIENT IDFIRST NAMELAST NAMESTREETCITYZIP CODE. The entity "CLIENT" violates the third rule of normal form (3NF). This rule states that all attributes must be functionally dependent on the primary key. In this case, the primary key is CLIENT ID, but the attributes FIRST NAME, LAST NAME, STREET, CITY, and ZIP CODE are not functionally dependent on it. To be in 3NF, each of these attributes would need to be related to CLIENT ID in such a way that they could not be determined by any other attribute.
For example, a separate entity for ADDRESS could be created with STREET, CITY, and ZIP CODE as attributes, and then related to the CLIENT entity through a foreign key.
To learn more about Entity attributes : https://brainly.com/question/13438918
#SPJ11
3
Biocatalysis helps create flavors and scents through what process?
altering DNA
chemical reactions
purifying components in a formula
aiding with the decomposition process
Answer:
its B. ima keep it short its B
Explanation
technician a says that brake fluid that is allowed to remain uncovered absorbs water. technician b says that if brake fluid is accidentally spilled on a fender of a vehicle, it can damage the paint. who is correct?
Technician A and Technician B both are correct as brake fluid that is allowed to remain uncovered does absorb water and brake fluid can damage the paint on a vehicle's fender if it is accidentally spilled.
Technician A is correct because brake fluid is hygroscopic, which means it absorbs moisture from the atmosphere. This water can corrode brake parts and lead to failure, as well as increase the fluid's boiling point, leading to brake fade and reduced stopping power.
Technician B is also correct because brake fluid is made up of corrosive materials that can break down paint and other surfaces. If the brake fluid is not cleaned off the fender immediately, it can cause permanent damage to the paint.
You can learn more about corrosive materials at: brainly.com/question/29632416
#SPJ11
what is the process called that produces particles of nearly uniform size that are much more likely to produce a solid ceramic without gaps or cracks?
This process is called dry pressing. Dry pressing is a method of producing particles of nearly uniform size, allowing for the production of solid ceramics without gaps or cracks. It is done by compressing a powder between two flat, parallel dies.
This process creates uniform shapes, with a consistent and uniform distribution of size. The process begins by weighing out a predetermined amount of ceramic powder, which is then mixed with a small amount of liquid binder to form a malleable paste. The paste is then placed in the press cavity and pressed by the two dies until the desired shape is achieved. The pressure used can range from 1-2 tons per square inch, depending on the material and desired shape. The pressure helps to reduce the number of particles, which increases their uniformity.
After pressing, the material is typically heated and sintered. Sintering is a process that reduces the size of the grains, increasing the density of the material. This further increases the strength of the ceramic piece and improves its uniformity.
Dry pressing is a simple and cost-effective method for producing particles of nearly uniform size and making solid ceramics without gaps or cracks. It is used in a variety of industries and applications, from electronics to medical devices.
You can learn more about Dry pressing at: brainly.com/question/10770691
#SPJ11
in the context of dynamic person-situation interaction, the main difference between evocation and manipulation is that:
Manipulation involves the intentional control of a situation by a person, whereas evocation is the process through which people elicit responses from others simply by displaying certain behaviors.
Manipulation is a term used in psychology to refer to the intentional control of a situation or environment by a person. It can be used to gain control over others, influence their behavior, or alter their perceptions.
Manipulation can be positive or negative, depending on the intention of the person doing the manipulating. Some forms of manipulation may involve deception, coercion, or exploitation.
On the other hand, evocation is a process through which people elicit responses from others simply by displaying certain behaviors. This is often done unintentionally, without the person being aware that they are having an impact on others.
Unlike manipulation, evocation does not involve intentional control over a situation or environment.
Learn more about manipulation here:
https://brainly.com/question/27154551
#SPJ11
for designing heat exchangers at the pinch, what is the criterion for matching streams above the pinch and what is the criterion for matching streams below the pinch? why are such criteria needed? (10 points)
The criteria for matching streams above the pinch for designing heat exchangers is to make sure that the hot stream and the cold stream are both having the same temperature. The criteria for matching streams below the pinch is to make sure that the hot stream and the cold stream have the same heat capacity.
These criteria are needed to ensure that there is an efficient heat exchange, meaning that the hot stream will give up most of its heat to the cold stream. In order for this to occur, it is essential that the temperature and heat capacity of the two streams are similar. If the temperatures of the hot and cold streams are too different, the efficiency of the heat exchange will be greatly reduced.
Similarly, if the heat capacities of the hot and cold streams are too different, the heat exchange will not be efficient. Thus, these criteria are necessary for efficient heat exchange.
You can learn more about heat exchangers at: brainly.com/question/22595817
#SPJ11
a 345 kv three-phase line supplies 614 mva at 0.74 pf lagging to a three-phase load which is delta connected. find the magnitude of complex impedance per phase in ohm up to two decimal places. you answered
The magnitude of the complex impedance per phase in ohms is 0.61 ohms (rounded to two decimal places).
To find the complex impedance per phase in ohms, we can use the following formula:
[tex]Z = V^2 / S[/tex]
where:
V = voltage per phase = 345 kV / sqrt(3) = 199.45 kV (assuming a balanced system)
S = apparent power per phase = 614 MVA / 3 = 204.67 MVA (assuming a balanced system)
The real power per phase is given by:
P = S * cos(phi) = 204.67 MW * 0.74 = 151.45 MW
The reactive power per phase is given by:
Q = S * sin(phi) = 204.67 MW * sin(arccos(0.74)) = 113.25 MVAr
The apparent impedance per phase is given by:
|Z| =
[tex]V / \sqrt{3} * \sqrt{(P^2 + Q^2) }/ S \\\\= 199.45 kV / \sqrt{3} * \sqrt{((151.45 MW)^2 + (113.25 MV \ Ar)^2)} / 204.67 MVA[/tex]
|Z| = 0.609 ohms (rounded to two decimal places)
For more question on magnitude click on
https://brainly.com/question/30216692
#SPJ11
Apart from replacement and displament deep foundations,
1. whats a third soloution and
2 method of installation ,
3. advantages, disadvantages
4. how it is connected to the foundation, then describe the role this connection plays resisting forces (e.g. lateral restraint, and others)
Alternative deep foundation: helical piles. Installed with torque, ideal for limited access sites, vibration-free. Resist lateral forces.
What is the explanation for the above response? The third solution for deep foundations is the use of micropiles.Micropiles are typically installed using a drilling rig, and the process involves drilling a small diameter hole (usually less than 30 cm) into the ground and then filling it with a high-strength grout material, followed by the installation of a steel reinforcing element.Advantages of using micropiles include their ability to be installed in low headroom areas, the ability to be installed in difficult soil conditions, and their low noise and vibration during installation. However, their load carrying capacity is typically lower than that of traditional piles, and their installation can be more expensive than other deep foundation solutions.Micropiles are connected to the foundation through a pile cap or a concrete footing, which transfers the load from the structure to the micropiles. The connection between the micropiles and the foundation provides lateral restraint and resists forces such as wind and earthquake loads. The micropiles can also provide uplift resistance, as they are typically installed at an angle to increase their effective length and capacity.Learn more about deep foundations at:
https://brainly.com/question/29341501
#SPJ1
a pair of large hydraulically operated shears is attached to the end of the boom on an excavator. the shear is used for cutting steel pipe and i-beams during demotion work. hydraulic cylinder ab exerts an 18kn force on the upper jaw. (a) complete the free-body diagram of the upper jaw, which has been only partially drawn. (b) determine the cutting force f being applied to the pipe.
Answer:
(a)
Free-body Diagram:
Upper Jaw:
F= 18kN
Friction force
Normal force
(b)
The cutting force f being applied to the pipe is equal to the force exerted by the hydraulic cylinder, 18kN.
what is the duty cycle (in percent) to get an average output of 3.7 v? enter your answer to the 2nd nearest decimal place.
The formula for duty cycle is as follows:Duty cycle = (Ton / T) * 100,Where Ton is the signal's active time, and T is the signal's total period.As a result, we can use this formula to calculate the duty cycle for the given average output voltage and frequency, as shown below:Duty cycle = (Vav / Vmax) * 100Duty cycle = (3.7 / 5) * 100Duty cycle = 74 percentTherefore, a duty cycle of 74 percent is required to obtain an average output of 3.7 volts.
The PWM signal's average voltage value varies as the duty cycle varies. The average voltage value is directly proportional to the duty cycle.
To get an average output of 3.7 v, what is the duty cycle (in percent)?The duty cycle is the fraction of the total period for which a signal or system is active, expressed as a percentage.
The duty cycle is used to express the relationship between the active time and the inactive time of a signal, for example.A PWM signal's output voltage is determined by the duty cycle. The on-time of the signal and the off-time of the signal can be changed with the duty cycle.
Learn more about duty cycle : https://brainly.com/question/26058582
#SPJ11
Please give a detail explanation, thank you
1) When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies.
True or false
2) If a semi-truck collides head-on with a mini car, which one will exert more force?
Semi-truck on the mini car
Mini car on the semi-truck
There is no force exerted
Both vehicles will exert equal force
The given statement "When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies" is False and there is usually some amount of permanent deformation during an impact when semi-truck collides head-on with a mini car.
The statement is False because In reality, there is usually some amount of permanent deformation that occurs during an impact, especially if the impact is severe. However, in many cases, the amount of deformation may be negligible or can be ignored for simplicity in calculations.Therefore the statement is False.
If a semi-truck collides head-on with a mini car then According to Newton's Third Law of Motion, every action has an equal and opposite reaction. Therefore, both the semi-truck and the mini car will exert equal force on each other during a head-on collision. The force experienced by each vehicle will depend on factors such as their mass, speed, and the duration of the impact. However, it is likely that the semi-truck, being much larger and heavier than the mini car, will experience less of a change in velocity than the mini car and therefore will exert more force on the smaller vehicle.
To practice more questions on force:
https://brainly.com/question/12970081
#SPJ11
Technology __________ guides how frequently technical systems are updated, and how technical updates are approved and funded.
a. wrap-up
b. turnover
c. governance
d. changeover
Technology governance guides how frequently technical systems are updated and how technical updates are approved and funded. Option C is correct.
Technology governance is the framework, policies, and procedures that regulate how an organization's IT infrastructure is managed and monitored. This involves defining how the company's technology-related activities are managed, including decision-making authority, accountability, and access to technology resources.
Technology governance entails establishing IT policies and procedures, providing training and guidance to employees on IT policies and procedures, defining the duties and responsibilities of IT personnel, ensuring regulatory compliance with technology-related laws, and defining how technical systems are updated and authorized for funding.
Technology governance guides how frequently technical systems are updated, and how technical updates are approved and funded.
For instance, it establishes the policies and procedures governing technical change management, risk management, and the decision-making process for technical projects. Technology governance also provides guidance on how to manage the technical resources that are deployed in the organization.
Therefore Option C is correct. Governance guides the technical system.
To learn more about Technology governance :
https://brainly.com/question/14364696
#SPJ11
this is a longitudinal section through the end of a finger. what is the correct name for the area circled in this virtual slide specimen?
The longitudinal segment through the end of a finger in this virtual slide specimen is known as Hyponychium the tissue located underneath the nail plate.
The hyponychium is the area of skin beneath the free edge of the nail plate, at the distal end of the finger or toe. It is sometimes referred to as the "quick" or the "nail bed seal,"
The hyponychium is an important part of the nail unit and is composed of specialized skin cells that help to support and protect the nail.
The hyponychium plays an important role in protecting the underlying nail bed and fingertip from damage, infection, and other types of trauma. Here are some of the benefits of the hyponychium:
1) Protection: The hyponychium acts as a barrier between the nail bed and the environment, protecting the underlying tissue from injury and infection.
2) Seal: The hyponychium seals the area between the nail plate and the nail bed, preventing dirt, debris, and bacteria from getting underneath the nail and causing infection.
3) Sensation: The hyponychium contains nerve endings that provide sensory feedback to the brain, allowing us to feel pressure, touch, and other sensations
For more such questions on finger
https://brainly.com/question/29891515
#SPJ11
Note- The correct question would be as below
This is a longitudinal section through the end of a finger. What is the correct name for the area circled in this virtual slide specimen?
what is for predict analysis using machine learning? a. data analysis b. data collection c. data engineering d. data science
For predictive analysis using machine learning, the correct option is (d) data science. The term "data science" is used to describe the techniques and methods employed by statisticians and computer scientists to extract value from data.
It involves obtaining and processing data to provide useful insights, which are then used to make informed business decisions. It is utilized in numerous fields, including healthcare, education, finance, and more. In the field of machine learning, data science is used to build predictive models that aid in the development of algorithms that can anticipate future outcomes.
For example, data science can be used to build a model that predicts which customers are most likely to leave a business, which can be used to create targeted marketing campaigns that incentivize them to stay. Data science is also used to create recommendation engines that predict which products a customer is most likely to purchase based on their purchase history.
Machine learning models have the potential to anticipate future results, while data science can be employed to educate and validate these models.
This necessitates the identification and purification of data, as well as the selection of pertinent variables for the issue at hand. Models are then established and verified for accuracy.
Learn more about machine learning : https://brainly.com/question/25523571
#SPJ11
Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers _______________.
A) are more accountable for what students learn
B) have students with a wider variety of learning needs
C) have more special students placed in their regular classrooms
Option B. In the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs.
According to Dewey, curriculum and institutions should be secondary to children in brain-based pedagogy since learning is socially produced. Students have to apply prior knowledge to generate new meaning in order to effectively learn.
This is what makes individualized instruction complex.Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs. Student-centered learning, on the other hand, has been a popular idea in education for years.
The popularity of student-centered learning can be traced back to John Dewey, a prominent educational philosopher. In Dewey's view, student-centered learning focused on the student's experience, interests, and interaction with the environment. Therefore the correct option is B.
Learn more about "teachers" at: https://brainly.com/question/28328532
#SPJ11
a 1,200a feeder is tapped (over 10ft but less than 25 ft long)to supply a 225a main breaker panelboard having a 180a continuous load. what's the minimum size thhn copper feeder tap conductor that can be used?
The correct answer is To determine the minimum size of the THHN copper feeder tap conductor, we need to calculate the ampacity of the tap conductor based on the 75-degree Celsius column of the NEC table 310.16.
First, we need to find the equivalent ampacity of the 225A main breaker panelboard. Since it is a continuous load, we have to multiply it by 1.25. So, 225A x 1.25 = 281.25A. Next, we need to find the percentage of the feeder ampacity required for the tap conductor. The NEC table 310.16 allows tap conductors to have an ampacity not less than one-third of the rating of the overcurrent device protecting the feeder. Therefore, 1200A/3 = 400A. Finally, we can calculate the minimum size THHN copper feeder tap conductor using the following formula: Minimum conductor ampacity = (281.25A - 180A) + 180A = 281.25A Minimum conductor ampacity = 281.25A / 0.8 (derating factor) = 351.56A From the NEC table 310.16, the minimum size THHN copper conductor with an ampacity of 351.56A is 2/0 AWG. Therefore, the minimum size THHN copper feeder tap conductor that can be used is 2/0 AWG.
To learn more about minimum size click on the link below:
brainly.com/question/29727023
#SPJ1
true or false: since liquid can be considered as incompressible, the volume flow rates into and out of a steady flow device will remain constant.
Answer:
True
Explanation:
Since liquid can be considered as incompressible, the volume flow rates into and out of a steady flow device will remain constant. True, For a steady, incompressible flow, since the density is constant, it implies that the total volumetric flow rates entering and leaving a control volume are the same.
what are the desired characteristics or values for the following parameters of an ideal amplifier? briefly justify your answers. o phase change as a function of the frequency o common mode rejection ratio o input resistance o output resistance
All the alternatives mentioned are correct, as regards the desired characteristics or values for the parameters of an ideal amplifier.
Here are the desired characteristics or values for the following parameters of an ideal amplifier:
A) Phase shift as a function of frequency: Ideally, an amplifier should have a phase shift of zero across the entire frequency spectrum. This means that the output signal is in phase with the input signal and there is no delay in the signal.
B) Common mode rejection ratio (CMRR): CMRR measures the ability of an amplifier to reject signals that are common to both inputs (such as noise). For an ideal amplifier, the CMRR should be infinite, meaning that it perfectly rejects common-mode signals.
C) Input resistance: An ideal amplifier should have an infinite input resistance. In other words, it should not load down the signal source, and the source should be able to supply the signal without any loss.
D) Output resistance: An ideal amplifier should have zero output resistance, meaning that its output voltage doesn't change regardless of the load connected to its output.
Learn more about amplifier:
https://brainly.com/question/28996974
#SPJ11
a 0.85-hp motor is required by a ducted fan to produce a 24-in stream of air having a velocity of 40 ft/s. estimate the efficiency of the fan.
A 0.85-hp motor is required by a ducted fan to produce a 24-in stream of air having a velocity of 40 ft/s then the efficiency of the fan is 20.47.
The efficiency of a ducted fan is determined by the ratio of power output (the kinetic energy of the air stream) to the power input (the power of the motor). In this case, the power output can be calculated using the following equation:
Power Output = 0.5 x density of air (in kg per meter cube) x velocity of air (in m/s) x cross-sectional area of air (in meter square) x ( square of velocity of air (in m/s))
Since the velocity of the air is 40 ft/s (which is equivalent to 12.19 m/s), the power output can be calculated as follows:
Power Output = 0.5 x 1.2 kg/m3 x 12.19 m/s x (24 in x 24 in) x (12.19 m/s x 12.19 m/s) = 13024.7 Watts
The power input of the motor can be calculated using the following equation:
Power Input = 0.85 x 746 = 634.1 Watts
Therefore, the efficiency of the fan can be calculated using the following equation:
Efficiency = Power Output / Power Input = 13024.7 Watts / 634.1 Watts = 20.47
You can learn more about efficiency at: brainly.com/question/30280642
#SPJ11
Kelvin contact resistance test structure in Fig. P3. 19, it is usually assumed that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm
In the Kelvin contact resistance test structure in Fig. P3.19, it is usually assumed that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm.
This assumption is made because the purpose of the Kelvin contact resistance test is to measure the resistance of a contact without including the resistance of the contact leads.To achieve this, the current is passed through the current leads, and the voltage is measured using the voltage leads. However, if the voltage leads have any resistance, this will add to the measured resistance value, making it inaccurate. To avoid this, the Kelvin contact resistance test structure uses two sets of voltage leads, one to carry the current and another to measure the voltage, so that any resistance in the measurement leads is not included in the measured resistance value.By assuming that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm, the Kelvin contact resistance test structure ensures that any resistance in the measurement leads is insignificant compared to the resistance of the contact being measured. This allows for accurate measurement of contact resistance and is a common technique used in electrical testing.for more such question on voltage
https://brainly.com/question/1176850
#SPJ11
is represented by a set of / data fields / variables (also known as properties or attributes) with their current value. it is is called____
In this case, the question is: "is represented by a set of / data fields / variables (also known as properties or attributes) with their current value. it is is called____"
The answer is: An object is represented by a set of data fields or variables (also known as properties or attributes) with their current value. It is called an object.
What is an object?
An object is an instance of a class in object-oriented programming. It is a software bundle of variables and related methods. An object is defined by its class, which determines its attributes (properties or variables) and methods (functions). An object is an instance of a class that has its own identity, state, and behavior.
The state of an object is represented by its attributes, while its behavior is represented by its methods. Therefore, an object is represented by a set of data fields or variables (also known as properties or attributes) with their current value, and it is called an object.
To learn more about object-oriented programming : https://brainly.com/question/3522354
#SPJ11
all of the windings of three phase motors are always wired how?
Three-phase motor windings can be wired in a delta or star configuration. Delta is for high power, star for low. Configuration depends on motor design and operating requirements.
The windings of a three-phase motor can be wired in either a delta or star (also called wye) configuration.
In a delta connection, the windings are connected in a triangle, with each end of a winding connected to the start of the next winding. This type of connection is commonly used for high voltage and high current applications, as it can handle higher power levels than a star connection.
In a star connection, the windings are connected in a Y shape, with one end of each winding connected to a common point called the neutral or star point, and the other ends of the windings connected to the three-phase power supply. This type of connection is typically used for low voltage and low current applications, as it is easier to connect and provides a neutral point for grounding.
The specific configuration used depends on the motor's design, operating requirements, and the power supply available.
To learn more about Three-phase motor windings:
https://brainly.com/question/26236885
#SPJ11
the equation used to determine the approximate amount of of critical stress to propagate a crack is known as the friffith equation the griffith equation is
The Griffith equation is used to calculate the approximate amount of critical stress necessary to propagate a crack. The formula for the equation is K = √(πE/2Y), where E is Young's modulus, and Y is the geometrical factor, which depends on the shape of the crack.
The equation is based on the energy release rate for crack propagation and was developed by A.A. Griffith in 1921. The equation is used to calculate the stress intensity factor (K) for a crack in an elastic material.
The Griffith equation is important for engineers as it can be used to estimate how much stress a material can withstand before it will fracture. This is important when designing components or structures that will be subject to loading or fatigue. Additionally, the equation can be used to calculate the stress concentration factor (Kt) at a point of crack initiation.
In conclusion, the Griffith equation is an important equation used to calculate the approximate amount of critical stress necessary to propagate a crack. This equation can be used by engineers to ensure that their designs are able to withstand the expected loads, as well as calculate stress concentration factors.
You can learn more about Griffith at: brainly.com/question/30188283
#SPJ11
A body is projected at 50m/s vertically upwards from the top of a building which is 120m high. Calculate:
i The time taken to reach a point P, 40m above the ground,
This is about projectiles and the time taken to reach point P, 40 meters above the ground, is approximately 4.04 seconds.
What is the explanation for the above response?To solve this problem, we can use the kinematic equation that relates displacement, initial velocity, final velocity, acceleration, and time:
y = vi*t + (1/2)at^2
where y is the displacement (in meters), vi is the initial velocity (in meters per second), a is the acceleration (in meters per second squared), and t is the time (in seconds).
At the top of the building, the body has an initial velocity of 50 m/s, which is purely vertical. The acceleration due to gravity is -9.8 m/s^2 (negative because it acts downward).
When the body reaches point P, its displacement from the top of the building is 120 m - 40 m = 80 m.
So, we can use the above equation to find the time taken to reach point P:
80 = 50t + (1/2)(-9.8)*t²
Simplifying and solving for t, we get:
4.04 seconds
Therefore, the time taken to reach point P, 40 meters above the ground, is approximately 4.04 seconds
Learn more about projectiles at:
https://brainly.com/question/13388411
#SPJ1
Which is a small plain text file that a website might place on your local drive?
Answer:A cookie
Explanation:To track interests.
air is compressed steadily and adiabatically from 290k, 90 kpa to 480k, 390 kpa. what is the isentropic efficiency of the compressor? a
The Isentropic efficiency of the compressor Let's consider the given parameters; Initial conditions: T1 = 290 kP1 = 90 kPa Final conditions: T2 = 480 kP2 = 390 kPa The isentropic efficiency of the compressor can be calculated using the following formula:ηs = (h2s - h1) / (h2 - h1)Whereηs = Isentropic efficiency of the compressorh1 = Enthalpy at the inlet of the compressorh2 = Enthalpy at the outlet of the compressorh2s = Isentropic enthalpy at the outlet of the compressor.
Now let's calculate the enthalpies; From the given conditions, we can find out the state point of the air at the inlet of the compressor using the steam tables: At P1 = 90 kPa, T1 = 290 K Using the steam tables, we find out h1 = 315.83 kJ/kg Similarly, we can find out the state point of the air at the outlet of the compressor using the steam tables: At P2 = 390 kPa, T2 = 480 K Using the steam tables, we find out h2 = 421.45 kJ/kg Now, let's calculate the isentropic enthalpy at the outlet of the compressor: Using the steam tables, we can find out the state point of the air at the outlet of the compressor if it were isentropic. At P2 = 390 kPa and S1 = S2Using the steam tables, we find out h2s = 455.41 kJ/kg Substituting these values in the isentropic efficiency formula, we get;ηs = (h2s - h1) / (h2 - h1)ηs = (455.41 - 315.83) / (421.45 - 315.83)ηs = 0.72Thus, the isentropic efficiency of the compressor is 72%.
for more such questions on parameters.
https://brainly.com/question/30380032
#SPJ11
what is an impact, ballistic or creep ripple? what is the length of these ripples relative to their heights? how does this ratio compare to those for aerodynamic and hydrodynamic ripples?
Impact, ballistic, and creep ripples are all types of surface features that can occur on materials subjected to different types of stresses.
Impact ripples are formed when a material is struck by a projectile or another object. Ballistic ripples are similar but are specifically formed by high-velocity projectiles. Creep ripples, on the other hand, are formed when a material is subjected to a constant stress over a long period of time, causing it to slowly deform.
The length of these ripples relative to their heights can vary depending on the specific material and conditions. However, in general, the ripples tend to have a relatively short wavelength compared to their height.
In comparison, aerodynamic and hydrodynamic ripples are formed by the flow of air or water over a surface. These ripples tend to have a much longer wavelength compared to their height, with the length-to-height ratio typically ranging from several to tens of thousands. This is because the fluid flow over the surface is generally much smoother and less abrupt than the stresses that cause impact, ballistic, and creep ripples.
To learn more about stresses refer to:
brainly.com/question/30128830
#SPJ4
it takes 2 hours to charge a cell phone. If the battery is drained during two days of use, compare the power required to charge the phone to the average power the phone uses during the two days
To compare the power required to charge the phone to the average power the phone uses during the two days, we need to make some assumptions about the phone's battery capacity and power usage.
What is the power about?Let's assume that the phone has a battery capacity of 3000 mAh (milliampere-hour) and that its average power usage during the two days is 150 mA. We can use these assumptions to estimate the energy used by the phone during the two days and the energy required to charge the phone.
Energy used during two days = power x time
= 150 mA x 2 days x 24 hours/day
= 7200 mAh
Energy required to charge phone = battery capacity x charging efficiency
= 3000 mAh x 100% (assuming 100% charging efficiency)
= 3000 mAh
Now, we can compare the energy required to charge the phone to the energy used during the two days:
Energy required to charge phone = 3000 mAh
Energy used during two days = 7200 mAh
We can see that the energy used during the two days (7200 mAh) is more than twice the energy required to charge the phone (3000 mAh). This means that the average power usage of the phone during the two days (150 mA) is much lower than the power required to charge the phone (3000 mAh / 2 hours = 1500 mA).
Therefore, This makes sense because the phone's power usage is spread out over a longer period of time, whereas the power required to charge the phone is concentrated in a shorter period of time. Therefore, even though it takes 2 hours to charge the phone, the power required to charge the phone is much higher than the average power the phone uses during the two days of use.
Learn more about power from
https://brainly.com/question/24174383
#SPJ1
explain the difference in the importance of drafts in green-sand casting versus permanent-mold casting.
In green-sand casting, drafts are essential because they provide a gradual slope in the molds that allows the casting to be released easily.
Drafts are not as important in permanent-mold casting because the mold is generally made of metal and can be more easily broken apart. Drafts can still be used in permanent-mold casting, but they are not as necessary.
Greensand is a mixture of quartz sand, water and bentonite. The sample product used is a 90o elbow measuring 0.5 inches with white cast iron material. The surface roughness was observed by visual observation of the casting results of the two green sand mold compositions.
Learn more about green sand : https://brainly.com/question/29850244
#SPJ11
the manganese content of a certain stainless steel is to be verified by an activation measurement. the activity induced in a sample of volume v by neutron capture during a time t is given by
By measuring the activity of a sample over time, the manganese content of stainless steel can be verified.
The manganese content of certain stainless steel can be verified by an activation measurement. Activation measurements measure the activity induced in a sample by neutron capture during a specific time period. Activity is given by the equation A = N0e-λt, where N0 is the initial number of atoms, e is Euler's number (2.718...), λ is the decay constant, and t is time. In this equation, A is the activity at a time t and N0 is the initial number of atoms. The decay constant λ indicates the probability of a neutron capture reaction and is dependent on the material's manganese content.
You can learn more about manganese content at: brainly.com/question/29437774
#SPJ11