Draw shear Force and bending moment diagram for the beam given below.
Answers
The primary purpose of beams as structural components is to support vertical loads.
What is Force and bending moment?The highest shear and maximum moment locations, as well as the corresponding magnitudes, should be noted while constructing a beam because there is where the structure is most likely to break.
We must measure the shear force and bending moment at every location along the whole length of the beam in order to identify these important places. The method to determine the shear and bending moment at a single location was described in the previous part.
While this method is helpful, you will need a more potent strategy to determine the shear and moment at every point in the item. A shear and bending moment diagram can be made to do this.
Therefore, The primary purpose of beams as structural components is to support vertical loads.
To learn more about Bending moment, refer to the link:
https://brainly.com/question/30242055
#SPJ1
Related Questions
for his position as a lead mechanic, jeff needs to know when and how to use a 12 millimeter screwdriver and a 14 millimeter screwdriver for a specific task. this requires
Answers
Technical Knowledge is the understanding of the specific tools, techniques, and processes required to complete a task. In this case, Jeff needs to have a thorough understanding of when and how to use a 12 millimeter screwdriver and a 14 millimeter screwdriver for a specific task.
This requires him to have a deep understanding of the tools and techniques require completing the task, as well as the processes involved in using the tools correctly. Jeff must also be able to identify any potential risks or issues that may arise during the task and take steps to mitigate them. Additionally, Jeff must be able to troubleshoot any problems that may arise during the task and take the necessary steps to resolve them. Jeff must also be able to identify any potential safety hazards associated with the task and take steps to ensure that they are addressed. Jeff must be able to provide regular updates to his supervisor on the progress of the task and ensure that any changes or modifications are communicated in a timely manner. Finally, Jeff must be able to provide feedback and advice to his supervisor in order to ensure that the task is completed successfully.
Learn more about Technical Knowledge here
https://brainly.com/question/25053983
#SPJ4
given a string s of characters, a subsequence of s, defined by the indices i 1, i 2, ..., i m , is said to be a repeated subsequence if you can find another sequence of indices j 1, j 2, ..., j m, such that s[i k]
Answers
Answer:
= s[j k] for all 1 <= k <= m.
In other words, a repeated subsequence is a sequence of characters within the original string that appears in the same order at least twice. The indices i1, i2, ..., im refer to the positions of the characters in the original string that make up the repeated subsequence, and the indices j1, j2, ..., jm refer to the positions of the same characters in the second occurrence of the repeated subsequence.
Carbon steel (AISI 1010) shafts of 0. 1 - m diameter are heat treated in a gas - fired furnace whose gases are at 1200 K and provide a convection coefficient of 100 W/m2,K. If the shafts enter the furnace at 300 K, how long must they remain in the furnace to achieve a centerline temperature of 800 K?
Answers
800 K's center line temperature must be attained in t = 58 seconds.
Explain about the centerline temperature?The normalized centerline temperature is determined by where the horizontal line crisscrosses the y-axis. Now, we'll use the second chart to determine the temperature at any point within the solid.
Following is the fundamental data: Surface energy balance equation, first: H = Rn - G - L. E, where H denotes the sensible heat flow from surface to air, Rn denotes net radiation to the surface, G denotes the heat absorbed into the soil, L denotes the latent heat of evaporation, and E denotes the rate of evaporation.
The temperature gradient of a heated body in a steady condition is defined as the ratio of the temperature difference to the distance between two places.
Given data
D = 0.1 m
h = 100
Carbon steel's specific heat (C) is 502.4.
1200 K is the furnace temperature.
800 K is the final temperature.
300 K at initial temperature
From the equation now (1)
㏑ 0.44 = -(0.001415 ) t
-(0.001415 ) t = - 0.82
t = 58 sec
To learn more about centerline temperature refer to:
https://brainly.com/question/16398731
#SPJ4