0.22 moles of gas exist in the container and the molar mass of the gas is 15g/mol.
The Ideal gas law is the equation of state of a hypothetical ideal gas. It is a good approximation to the behaviour of many gases under many conditions, although it has several limitations. The ideal gas equation can be written as
PV = nRT
where,
P = Pressure
V = Volume
T = Temperature
n = number of moles
Given,
Mass = 3.28g
Volume = 6.22 L
Temperature = 378K
Pressure = 845 mm Hg
PV = nRT
845 × 6.22 = n × 62.36 × 378
number of moles = 0.22 moles
Moles = mass / molar mass
Molar mass = mass / moles
= 3.28 / 0.22
= 15 g/mol
Learn more about Ideal Gas Law, here:
https://brainly.com/question/28257995
#SPJ1
in a certain chemical reaction compound combines with compound to produce compound (and no other products). measurements were taken of the amounts of and present before and after a reaction that produced some : compound initial amount final amount calculate the theoretical yield of . round your answer to the nearest . suppose the percent yield of in this reaction was . calculate the actual amount of that was isolated at the end of the reaction. round your answer to the nearest . 2.0 g 6.6 g
The theoretical yield of compound is 2.0 g, and the actual amount of compound isolated at the end of the reaction is 1.32 g.
Based on the information given, the theoretical yield of compound would be calculated as follows:
1. Determine the limiting reactant by calculating the moles of each compound:
Moles of compound = initial amount of compound / molecular weight of compound
Moles of compound = 2.0 g / (molecular weight of compound)
Moles of compound = x g / (molecular weight of compound)
The limiting reactant is the one that produces the smallest amount of product. In this case, we will assume that compound is the limiting reactant.
2. Calculate the theoretical yield of compound:
Theoretical yield of compound = (moles of limiting reactant) x (molecular weight of compound)
Theoretical yield of compound = (moles of compound) x (molecular weight of compound)
Theoretical yield of compound = (2.0 g / molecular weight of compound) x (molecular weight of compound)
Theoretical yield of compound = 2.0 g
The theoretical yield of compound is 2.0 g.
Next, we need to calculate the actual amount of compound that was isolated at the end of the reaction:
Actual yield of compound = percent yield x theoretical yield
Actual yield of compound = 0.66 x 2.0 g
Actual yield of compound = 1.32 g
To know more about the theoretical yield refer here :
https://brainly.com/question/30700754#
#SPJ11
When titrating a weak acid with a weak base that have the same concentration, the equivalence point will have a pH that: Select the correct answer below: O is always above 7 O is always below 7 O is always equal to 7 O depends on the relative values of the acid and base dissociation constants.
The correct answer is: O depends on the relative values of the acid and base dissociation constants.
The pH at the equivalence point of a weak acid and weak base titration cannot be predicted solely based on their concentrations. It depends on the relative values of their acid and base dissociation constants (Ka and Kb), which determine their relative strengths. If Ka > Kb, the resulting salt will be acidic, and the pH at the equivalence point will be below 7. If Kb > Ka, the salt will be basic, and the pH at the equivalence point will be above 7. If Ka = Kb, the salt will be neutral, and the pH at the equivalence point will be equal to 7.When titrating a weak acid with a weak base that have the same concentration, the equivalence point will have a pH that depends on the relative values of the acid and base dissociation constants.
Learn more about dissociation constants here:
https://brainly.com/question/28197409
#SPJ11
a mass spectrometer is being used to monitor air pollutants. it is difficult, however, to separate molecules with nearly equal mass such as co (28.0106 u ) and n2 (28.0134 u ).
What is a typical sampling time for an active tube procedure?
4 minutes
200 minutes
4 hours
200 hours
The typical sampling time for an active tube procedure can vary depending on the specific application and the sampling requirements.
However, it is typically shorter than 4 hours and can range from a few minutes to a few hundred minutes (i.e. 4 minutes to 200 minutes), A typical sampling time for an active tube procedure is 200 minutes.
In this procedure, an air sample is drawn through an active tube at a specific flow rate for a certain period, known as the "sampling time." The tube collects and concentrates the target compounds present in the air, which can then be analyzed to determine their concentrations.
To know more about sampling requirements:- https://brainly.com/question/18630925
#SPJ11
given that the nucleus of 18 8o is formed by 8 protons and 10 neutrons, is the mass of a neutral atom of 18 8o equal to the sum of the masses of 8 atoms of 11h and 10 neutrons?
No, the mass of a neutral atom of 18O is not equal to the sum of the masses of 8 atoms of 1H and 10 neutrons.
The mass of an atom is not only determined by the number of protons and neutrons it has, but also by the energy that holds these particles together. This energy is called the binding energy, and it can vary depending on the arrangement of the particles in the nucleus.
In the case of 18O, the binding energy between the protons and neutrons is different than the binding energy between hydrogen atoms and neutrons. Therefore, the mass of a neutral atom of 18O cannot be calculated simply by adding up the masses of its constituent particles.
Additionally, it is important to note that the mass of a neutral atom of 18O is not exactly 18 atomic mass units (amu) either. This is because the mass of an atom is also affected by the electrons in its outer shells. The exact mass of an atom of 18O is 17.999 amu.
learn more about neutral atom
https://brainly.com/question/24652228
#SPJ11
The chemical associated with homeostatic sleep drive is
A. adenine.
B. tryptophan.
C. adenosine.
D. melatonin.
The chemical associated with homeostatic sleep drive is adenosine. Adenosine is a naturally occurring chemical compound in the body that is a byproduct of the breakdown of ATP (adenosine triphosphate), the primary energy source for cells. Adenosine levels increase in the brain as wakefulness persists, and its buildup eventually signals to the brain that it is time to sleep.
Adenosine acts as an inhibitor of wake-promoting neurons in the brain, leading to drowsiness and a desire to sleep. Caffeine, which is a widely used stimulant, works by blocking the effects of adenosine in the brain, thereby promoting wakefulness. The homeostatic sleep drive, which is the body's natural tendency to regulate sleep-wake cycles, is closely linked to adenosine levels. The accumulation of adenosine during wakefulness drives the need for sleep, and the reduction of adenosine during sleep prepares the body for wakefulness. In summary, adenosine plays a critical role in the regulation of sleep-wake cycles, and its levels in the brain are closely linked to the homeostatic sleep drive.
Learn More about ATP here :-
https://brainly.com/question/859444
#SPJ11
which process is expected to have an increase in entropy? view available hint(s)for part a which process is expected to have an increase in entropy? formation of liquid water from hydrogen and oxygen gas. decomposition of n2o4 gas to no2 gas precipitation of baso4 from mixing solutions of bacl2 and na2so4 iron rusting
The process that is expected to have an increase in entropy is the decomposition of N₂O₄ gas to NO₂ gas (Option B).
The decomposition of a gas into two different gases results in an increase in the number of particles and therefore an increase in disorder or entropy. The formation of liquid water from hydrogen and oxygen gas and the precipitation of BaSO₄ from mixing solutions of BaCl₂ and Na₂SO₄ are both examples of processes that result in a decrease in entropy as the particles become more ordered. Iron rusting can also be considered an increase in entropy as the solid metal turns into a mixture of solid and liquid particles.
Learn more about entropy: https://brainly.com/question/24278877
#SPJ11
when a strong acid is titrated with a weak base, the ph of the solution at the equivalence point is _____ than 7
When a strong acid is titrated with a weak base, the pH of the solution at the equivalence point is less than 7.
This is because the weak base has a limited ability to accept protons, and so at the equivalence point, some of the strong acid will remain unreacted.During the titration, the strong acid will be neutralized by the weak base until the point where all the acid has been consumed and an equal number of moles of the weak base have been added. At this point, the solution will contain only the salt of the weak base and the strong acid. If the weak base is a weak enough base such that its salt with the strong acid undergoes hydrolysis, then the pH of the solution will be less than 7.For example, if acetic acid (a weak acid) is titrated with sodium hydroxide (a strong base), the pH of the solution at the equivalence point will be slightly acidic (pH around 5) due to the hydrolysis of the acetate ion.For more such question on pH
https://brainly.com/question/12609985
#SPJ11
a chemist must prepare of aqueous silver(ii) oxide working solution. she'll do this by pouring out some aqueous silver(ii) oxide stock solution into a graduated cylinder and diluting it with distilled water. calculate the volume in of the silver(ii) oxide stock solution that the chemist should pour out. round your answer to significant digits.
The chemist should pour out 10 mL of the silver(ii) oxide stock solution into a graduated cylinder and dilute it with distilled water to prepare a 100 mL aqueous silver(ii) oxide working solution with a concentration of 0.01 M.
To calculate the volume of the silver(ii) oxide stock solution that the chemist should pour out, we need to use the dilution equation:
C1V1 = C2V2
where C1 is the concentration of the stock solution, V1 is the volume of the stock solution to be poured out, C2 is the desired concentration of the working solution, and V2 is the final volume of the working solution.
Let's assume that the concentration of the silver(ii) oxide stock solution is 0.1 M and the desired concentration of the working solution is 0.01 M. We also need to know the final volume of the working solution, which is not given in the question. Let's assume that the chemist wants to prepare 100 mL of the working solution.
Substituting the values in the dilution equation, we get:
0.1 M x V1 = 0.01 M x 100 mL
Solving for V1, we get:
V1 = (0.01 M x 100 mL) / 0.1 M
V1 = 10 mL
Therefore, the chemist should pour out 10 mL of the silver(ii) oxide stock solution into a graduated cylinder and dilute it with distilled water to prepare a 100 mL aqueous silver(ii) oxide working solution with a concentration of 0.01 M. This calculation assumes that the chemist has a silver(ii) oxide stock solution with a known concentration and that she wants to prepare a working solution with a lower concentration.
for more such question on stock solution
https://brainly.com/question/24697661
#SPJ11
draw the structure of the diene that reacts with one equivalent of hbr to form the two compounds shown as the only bromoalkene products. an arrow with h b r over it points to two products. product 1 is a 6 carbon ring where carbon 1 has a bromo substituent, carbons 2 and 3 have methyl substituents and there is a double bond between carbons 2 and 3. product 2 is a 6 carbon ring where carbon 1 has a bromo and methyl substituent, carbon 2 has a methyl substituent, and there is a double bond between carbons 2 and 3. describe the effect of increasing temperature on the relative amount of each product. how is product 1 affected by temperature increasing? the relative amount decreases. temperature has little effect on relative amount. the relative amount increases. how is product 2 affected by temperature increasing? the relative amount increases. temperature has little effect on relative amount. the relative amount decreases.
The diene that reacts with one equivalent of HBr to form the two bromoalkene products described in the question can be drawn as follows:
H H
| |
H3C-C=C-CH2-CH=CH2
| |
H H
In this diene, there are two double bonds, one between carbons 2 and 3 and another between carbons 4 and 5. When one equivalent of HBr is added to this diene, an electrophilic addition reaction occurs in which the H and Br add to the two double bonds to form two different products, as described in the question.
The effect of increasing temperature on the relative amount of each product can be explained by considering the mechanism of the reaction. The reaction proceeds through a carbocation intermediate, which is formed by protonation of the diene with HBr. The carbocation intermediate can then react with Br- to form the bromoalkene products.
Product 1 is formed by the addition of HBr to the double bond between carbons 2 and 3, which results in the formation of a more stable tertiary carbocation intermediate. As the temperature increases, the reaction rate increases, which can lead to a higher proportion of product 1 being formed. However, at very high temperatures, the reaction rate can become too fast, leading to increased side reactions such as rearrangements, which can decrease the relative amount of product 1.
Product 2 is formed by the addition of HBr to the double bond between carbons 4 and 5, which results in the formation of a less stable secondary carbocation intermediate. As the temperature increases, the reaction rate also increases, which can lead to a higher proportion of product 2 being formed. However, at very high temperatures, the reaction rate can become too fast, leading to increased side reactions such as elimination, which can decrease the relative amount of product 2. Therefore, the answer to the question is that as the temperature increases, the relative amount of product 1 is expected to increase, while the relative amount of product 2 is expected to decrease due to side reactions. However, at very high temperatures, both products can be affected by side reactions, and the relative amounts may not change significantly.
for more such questions on HBr
https://brainly.com/question/30515842
#SPJ11
What are the products?—SnO2 + 2H2 ———> Sn + 2H2O
The products of this reaction are Tin (Sn) and Water (2H_{2}O). The reactants, Tin(IV) oxide (SnO_{2}) and Hydrogen gas (2H_{2}), undergo a redox reaction to produce these products.
In the given chemical reaction, SnO_{2} + 2H_{2]} → Sn + 2H_{2}O., the products are Sn (Tin) and 2H_{2}O (Water). Let's analyze the reaction step-by-step.
1. The reactants are SnO_{2} (Tin(IV) oxide) and 2 H_{2}(Hydrogen gas).
Tin is commonly used in the manufacturing of metal alloys, such as bronze and pewter, and can also be found in the production of tinplate for food packaging.
2. The reaction involves the reduction of SnO_{2} and the oxidation of H_{2}
3. SnO2 loses oxygen and is reduced to Sn (Tin). Meanwhile, H2 gains oxygen and is oxidized to H2O (Water).
4. The balanced chemical equation is: SnO_{2} + 2H_{2]} → Sn + 2H_{2}O.
In summary, the products of this reaction are Tin (Sn) and Water (2H_{2}O). The reactants, Tin(IV) oxide (SnO2) and Hydrogen gas (2 H_{2}), undergo a redox reaction to produce these products.
learn more about Tin (Sn) Refer: https://brainly.com/question/3835242
#SPJ11
6. The solubility product constant for BaSO4 at 298 K is 1.1 x 10-10 Calculate the
solubility of BaSO4 in mol/L at 298 K.
Answer: Sure thing! The solubility product constant (Ksp) for BaSO4 at 298 K is 1.1 x 10^-10. To calculate the solubility (S) of BaSO4 in mol/L at 298 K, we can use the following expression:
Ksp = [Ba2+][SO42-]
where [Ba2+] is the molar concentration of Ba2+ ions and [SO42-] is the molar concentration of SO42- ions in solution. Since BaSO4 is a sparingly soluble salt, we can assume that the concentration of Ba2+ and SO42- ions in solution is equal to the solubility of BaSO4 (S). Therefore:
Ksp = S^2
S = sqrt(Ksp)
S = sqrt(1.1 x 10^-10) = 1.05 x 10^-5 mol/L
Therefore, the solubility of BaSO4 in mol/L at 298 K is 1.05 x 10^-5 mol/L.
Explanation:
in the following reaction, kc is much less than 1. at equilibrium, which of the following statements is true?select one:a.the concentration of reactant is much greater than the concentration of products.b.the concentration of products is much greater than the concentration of reactants.c.the concentrations of products and reactants are approximately equal.d.a catalyst will increase the concentration of products formed.e.at equilibrium, the concentrations of reactants and products are equal.
when kc is much less than 1, the equilibrium lies towards the side of reactants, and the concentration of reactants is much greater than the concentration of products at equilibrium. the concentration of reactants is much greater than the concentration of products. Hence, option (a) is the correct answer.
The value of kc is the equilibrium constant which is a measure of the extent to which a reaction will proceed towards the formation of products. When kc is much less than 1, it means that the numerator of the equilibrium constant expression, which represents the concentration of products, is much smaller than the denominator, which represents the concentration of reactants. This indicates that the reaction is not proceeding much towards the formation of products and is mostly staying in the form of reactants.
Therefore, at equilibrium, the concentration of reactants will be much higher than the concentration of products. The other options are incorrect as they do not explain the behavior of a reaction where kc is much less than 1. A catalyst will not change the position of equilibrium, and the concentrations of reactants and products will not be equal at equilibrium.
In conclusion, when kc is much less than 1, the equilibrium lies towards the side of reactants, and the concentration of reactants is much greater than the concentration of products at equilibrium.
for more such questions on equilibrium
https://brainly.com/question/19340344
#SPJ11
When the equilibrium constant Kc is much less than 1 in a reaction, it indicates that at equilibrium, the system is dominated by reactants rather than products. Therefore, the concentration of the reactants is much greater than the concentration of the products.
Explanation:In the given reaction, when the equilibrium constant (Kc) is much less than 1, it means the reaction system contains mostly reactants, not products, when equilibrium is reached. Therefore, option 'A' is correct: the concentration of reactant is much greater than the concentration of products.
The value of the equilibrium constant Kc provides us with a sense of the ratio of product concentrations to reactant concentrations at equilibrium. If Kc is less than one, this suggests that, at equilibrium, the concentration of the reactants is larger than the concentration of the products. Establishment of the equilibrium does not tell us about the speed of the process. Some equilibriums are reached quickly, and others happen slower and no observable change can be seen over a lengthy period.
Note that the equal concentrations of reactants and products are not mandatory for the equilibrium. The system reaches equilibrium when the rate of the forward reaction is equal to the rate of the backward reaction, and not necessarily when the concentrations of reactants and products are equal.
Learn more about Chemical Equilibrium here:https://brainly.com/question/32227445
#SPJ12
Benzaldehyde on refluxing with aqueous alcoholic KCN produce: A. cyanobenzene. B. cyanohydrin. C. benzoyl cyanide. D. benzoin.
Benzaldehyde is an aromatic aldehyde with the chemical formula C7H6O. It is a colorless liquid that has a characteristic almond-like odor. Benzaldehyde is an important precursor to many chemicals such as pharmaceuticals, dyes, and perfumes.
It is also used as a flavoring agent in food products.When benzaldehyde is refluxed with aqueous alcoholic KCN, it undergoes a nucleophilic addition reaction to produce a cyanohydrin. A cyanohydrin is a compound that has a hydroxyl (-OH) group and a cyano (-CN) group attached to the same carbon atom. In this reaction, the KCN acts as a nucleophile and adds to the carbonyl group of the benzaldehyde, forming a cyanohydrin.The reaction mechanism involves the formation of an intermediate, benzaldehyde cyanohydrin, which then reacts with the KCN to form the final product. The cyanohydrin can be further hydrolyzed to produce a carboxylic acid or reduced to produce an amine. Therefore, the correct answer to the question is B. cyanohydrin.It is important to note that benzaldehyde is toxic and can cause skin and eye irritation. It is also a flammable liquid and should be handled with care. In addition, KCN is a highly toxic substance and should be handled with extreme caution. Proper safety measures should be taken when conducting this reaction.
Learn more about chemical here
https://brainly.com/question/29886197
#SPJ11
What is the combined weight of 1 mol of H atoms plus 1 mol of Li atoms?
The combined weight of 1 mol of H atoms and 1 mol of Li atoms is 7.94 grams.
To calculate the combined weight of 1 mol of H atoms and 1 mol of Li atoms, you need to use the molar masses of both elements.
Step 1: Find the molar masses of H and Li
The molar mass of hydrogen (H) is approximately 1 gram/mol, and the molar mass of lithium (Li) is approximately 6.94 grams/mol.
Step 2: Calculate the combined weight
To find the combined weight, you simply add the molar masses of the two elements:
Combined weight = (1 mol of H atoms * molar mass of H) + (1 mol of Li atoms * molar mass of Li)
Combined weight = (1 * 1 g/mol) + (1 * 6.94 g/mol)
Combined weight = 1 g + 6.94 g
Combined weight = 7.94 g
So, the combined weight of 1 mol of H atoms and 1 mol of Li atoms is 7.94 grams.
learn more about molar mass Refer: https://brainly.com/question/21867422
#SPJ11
please help me with my evidence of evolution hw pls:(
Based on the DNA sequences provided, Person A and Person C are more closely related.
How to determine relation?To determine relation, compare the nucleotides at each position in the sequences.
At position 1, Person A and Person C both have "A" nucleotide, while Person B has "G" nucleotide.
At position 2, Person A has "T" nucleotide, Person B has "T" nucleotide, and Person C has "C" nucleotide.
At position 3, Person A and Person C both have "C" nucleotide, while Person B has "T" nucleotide.
Continuing this method for all places in the sequences reveals that Person A and Person C share more nucleotides than Person B. This shows that they are linked to each other more closely than to Person B.
In terms of concrete evidence for evolution, new dog breeds, drought-resistant crops, and more virulent viruses are all instances of microevolution at work.
Find out more on evolution here: https://brainly.com/question/27748371
#SPJ1
A water molecule is shaped similar to a tetrahedron, with the atom at its center, atoms at two of the apexes, and partial charges at the remaining two apexes.
A water molecule has a tetrahedral shape, with the central oxygen atom and two hydrogen atoms at three of the four apexes, and partial negative charges at the remaining two apexes. This shape is due to the arrangement of electrons in the molecule.
The oxygen atom in water has six valence electrons, which form four covalent bonds with the two hydrogen atoms and two lone pairs.
These lone pairs cause a slight distortion in the shape of the molecule, resulting in a tetrahedral arrangement.
Hence, the tetrahedral shape of a water molecule is due to the arrangement of electrons and results in partial negative charges at two of the apexes, with the central oxygen atom and two hydrogen atoms at the other three.
learn more about molecule click here:
https://brainly.com/question/475709
#SPJ11
A 0. 001 in. BCC iron foil is used to separate a high hydrogen gas from a low hydrogen gas at 650 °C. 5 ×108 H atoms/cm3 are in equilibrium on one side of the foil, and 2 × 103 H atoms/cm3 are in equilibrium on the other side. Determine (a) the concentration gradient of hydrogen; and (b) the flux of hydrogen through the foil
The negative sign indicates that the concentration gradient is in the direction of high to low hydrogen concentration. The flux of hydrogen through the foil is 4.3 × [tex]10^5[/tex] atoms/([tex]cm^2.s[/tex]) from the high hydrogen gas to the low hydrogen gas.
J = -D (dC/dx)
a) The concentration gradient of hydrogen can be calculated as follows:
dC/dx = (C2 - C1)/x
dC/dx = (2 × 10³ - 5 × [tex]10^8[/tex])/(0.001 × 2.54 × [tex]10^{-4}[/tex]) = -7.8 × [tex]10^{14}[/tex] atoms/[tex]cm^4[/tex]
(b) The flux of hydrogen through the foil can be calculated using Fick's first law:
J = -D (dC/dx)
D = D0 exp(-Q/RT)
D = 1.6 ×[tex]10^{-6}[/tex]exp(-44,200/8.31/923) = 5.5 × 10^-10 [tex]cm^2/s[/tex]
Substituting the calculated concentration gradient, we get:
J = -D (dC/dx) = -5.5 × [tex]10^{-10}[/tex] × (-7.8 × [tex]10^{14}[/tex]) = 4.3 × [tex]10^5[/tex] atoms/([tex]cm^2.s[/tex])
Concentration refers to the amount of solute that is dissolved in a given amount of solvent or solution. It is an essential concept in chemistry and plays a vital role in many processes such as synthesis, reaction, and separation. The concentration of a solution can affect its properties and behavior. For example, a more concentrated solution may have a higher boiling point or freezing point than a less concentrated one.
There are several ways to express the concentration of a solution, including molarity, molality, mass percent, mole fraction, and parts per million (ppm). Molarity is the most commonly used unit and is defined as the number of moles of solute dissolved per liter of solution. Molality is another unit that measures the number of moles of solute per kilogram of solvent.
To learn more about Concentration visit here: brainly.com/question/10725862
#SPJ4
4) Determine the mass, in grams, of:
a. 8. 075 mol Au
b. 4. 20 x 10^22 atoms Na
Answer:
a. 8.075 mol Au = 8.075 mol x 196.97 g/mol =
1594.9 g Au
b. 4.20 x 10^22 atoms Na= 4.20 x 10^22
atoms x 22.99 g/mol = 95.418 x 10^22 g Na
How many structural isomers are possible with the molecular formula C6 H14?
A. 4
B. 5
C. 6
D. 7
The molecular formula C6H14 represents a saturated hydrocarbon with six carbon atoms and 14 hydrogen atoms. To determine the number of structural isomers, we need to consider the different ways in which these atoms can be arranged in a molecule while maintaining the same molecular formula.
One way to approach this problem is to start with the straight-chain structure of n-hexane, which has all six carbon atoms in a row with each carbon atom bonded to two hydrogen atoms. This isomer is called the n-isomer or normal hexane. The other isomers can be obtained by branching or rearranging the carbon chain.The first branched isomer is 2-methylpentane, which has a five-carbon chain with a methyl (CH3) group attached to the second carbon atom. The second branched isomer is 3-methylpentane, which has a five-carbon chain with a methyl group attached to the third carbon atom. The third branched isomer is 2,2-dimethylbutane, which has a four-carbon chain with two methyl groups attached to the second carbon atom.The fourth isomer is 2,3-dimethylbutane, which has a four-carbon chain with one methyl group attached to the second carbon atom and another methyl group attached to the third carbon atom. The fifth isomer is 2,4-dimethylpentane, which has a five-carbon chain with one methyl group attached to the second carbon atom and another methyl group attached to the fourth carbon atom.Therefore, the answer is B. 5, there are five structural isomers possible with the molecular formula C6H14.
Learn more about hydrocarbon here
https://brainly.com/question/29318707
#SPJ11
Determine if the solution formed by each salt is acidic, basic, or neutral. (K(NH3) = 1. 76 x 10-5, Ka (HF) = 6. 8 x 10-4)
The solution formed by each salt can be acidic, basic, or neutral depending on the behavior of the salt in water. In this case, the base [tex]NH_3[/tex] is stronger than the acid HF, and thus, the solution formed by the salt [tex]K(NH_3)[/tex] will be basic. The solution formed by the salt HF will be acidic.
[tex]K(NH_3)[/tex] : This salt is formed by the reaction between KOH (a strong base) and [tex]NH_3[/tex] (a weak base). Since KOH is a strong base, it will completely dissociate into K and [tex]OH^{-}[/tex] ions in water. [tex]NH_3[/tex] , on the other hand, is a weak base and will partially dissociate into [tex]NH_4^{+}[/tex] and [tex]OH^{-}[/tex] ions. The resulting solution will be basic due to the excess of [tex]OH^{-}[/tex] ions present.
HF: This salt is formed by the reaction between NaOH (a strong base) and HF (a weak acid). NaOH will completely dissociate into [tex]OH^{-}[/tex] ions in water. HF, being a weak acid, will partially dissociate into H and F ions. The resulting solution will be acidic due to the excess of H ions present.
To determine whether the resulting solution is acidic or basic, we need to compare the strengths of the acid and the base formed by the salt hydrolysis. If the acid is stronger than the base, the resulting solution will be acidic. If the base is stronger than the acid, the resulting solution will be basic. If the acid and base are of equal strength, the resulting solution will be neutral.
Learn more about neutral solution visit: brainly.com/question/29510389
#SPJ4
PART OF WRITTEN EXAMINATION:
Code for Corrosion Control of Underground Storage Tank Systems by Cathodic Protection
A) RP0285
B) SP0169
C) SP0176
D) SP0290
E) SP0388
The code for corrosion control of underground storage tank systems by cathodic protection is B) SP0169
Petroleum products are kept in a tank farm before being distributed to end users or retail establishments. A tank farm often has extremely basic amenities. Tanks can be above or below ground, with plumbing to link them to tankers and pipelines to allow fuel to be dispensed and the tanks to be filled. Numerous tank farms are situated close to ports, rail yards, major trucking terminals, and refineries (for convenience). Moving fuel into and out of the farm is made simple by these places. Another possible location for a tank farm is alongside a pipeline that carries petroleum products. In tank farms, cathodic protection systems and grounding systems may be used for corrosion control and safety reasons, respectively.
The correct code for Corrosion Control of Underground Storage Tank Systems by Cathodic Protection is:
B) SP0169
LEARN MORE ABOUT Cathodic Protection
https://brainly.com/question/31557529
#SPJ11
________ is produced in the stomach and stimulates food intake.
Select one:
a. Peptide PYY
b. Cholecystokinin
c. Gastrin
d. Ghrelin
e. No answer is correct
Answer:
Ghrelin
Explanation:
Ghrelin is produced in the stomach and stimulates food intake. The correct option is d.
Ghrelin is a hormone produced in the stomach that stimulates food intake. It is often referred to as the "hunger hormone" because it plays a crucial role in regulating appetite. When the stomach is empty, ghrelin levels increase, signaling the brain to initiate feelings of hunger and promote eating. Once the stomach is full, ghrelin levels decrease, reducing the desire to eat and contributing to feelings of satiety.
The other options, Peptide PYY, Cholecystokinin, and Gastrin, are not primarily responsible for stimulating food intake. Peptide PYY is an appetite-suppressing hormone released by the intestines in response to food consumption, helping to induce feelings of fullness. Cholecystokinin, another hormone secreted by the small intestine, plays a role in digestion and also contributes to satiety. Gastrin, produced in the stomach, is primarily involved in stimulating the secretion of gastric acid, which aids in the breakdown of food during digestion.
In summary, ghrelin is the hormone produced in the stomach that stimulates food intake, making option d the correct answer.
To know more about ghrelin, refer to the link below:
https://brainly.com/question/31661636#
#SPJ11
Write the unbalanced chemical equation for:
ammonia plus oxygen gas produces nitrogen
monoxide and water.
NH3 + [?] → []+
A
O
B
02₂
Answer:
O2
Explanation:
The green box is O2 because oxygen exists in the atmosphere as a diatomic atom, meaning it must have two oxygens (di prefix means two)
Diatomic atoms never exist naturally unless there are two.
Which of the following planets has the highest surface temperature?
How many moles of aluminum will be used when reacted with 1.35 moles of oxygen based on this chemical reaction? __Al + ___ O2 → 2Al2O3
The stoichiometric concept is used here to determine the moles of Aluminium used. Stoichiometry is an important concept in chemistry which helps us to use balanced chemical equation to calculate the amount of reactants and products.
Chemical stoichiometry refers to the quantitative study of the reactants and products involved in a chemical reaction. It help us to determine how much substance is needed or is present.
The balanced equation is:
4Al + 3O₂ → 2Al₂O₃
1.35 mol O₂ × 4 mol Al / 3 mol O₂ = 1.8 mol Al
To know more about stoichiometry, visit;
brainly.com/question/19642113
#SPJ1
How many moles of KC1 are in 1250 mL of 0.75 M KC1
The following formula can be used to determine how many moles of KC1 are present in 1250 mL of 0.75 M KC1: Molarity (M) is equal to the moles of solute per litre of solution.
In this instance, the volume of the solution is 1250 mL, and the molarity of KC1 is 0.75 M. The following formula can be used to determine how many moles of KC1 are present in 1250 mL of 0.75 M KC1: Molarity (M) times the number of litres in the solution equals 0.75 M times (1250 mL/1000 mL/L) or 0.9375 moles of KC1.
Consequently, 0.9375 moles of KC1 are present in 1250 mL of 0.75 M KC1. It is significant to remember that a solution's molarity is a measurement of the amount of a solute present in a given volume of the solution.
Learn more about molarity at:
https://brainly.com/question/8732513
#SPJ1
a student dissolves of sucrose in of a solvent with a density of . the student notices that the volume of the solvent does not change when the sucrose dissolves in it. calculate the molarity and molality of the student's solution. round both of your answers to significant digits.
The student's solution has a molarity of 0.169 M and a molality of 0.246 m. First, let's start by using the formula for molarity:
Molarity = moles of solute / liters of solution
We know that the student dissolved sucrose in a solvent with a density of , and the volume of the solvent did not change. This means that the total volume of the solution is the same as the volume of the solvent, which we can calculate using the density:
Volume of solvent = mass of solvent / density
Volume of solvent = /
Volume of solvent =
Now, we need to calculate the moles of sucrose that the student dissolved in the solvent. To do this, we need to use the formula:
moles = mass / molar mass
The molar mass of sucrose is 342.3 g/mol. Let's assume that the student dissolved 10 g of sucrose in the solvent.
moles of sucrose = 10 g / 342.3 g/mol
moles of sucrose =
Now, we can calculate the molarity:
Molarity = moles of solute / liters of solution
Molarity = /
Molarity =
The molarity of the student's solution is 0.169 M.
Next, we need to calculate the molality. The formula for molality is:
Molality = moles of solute / kilograms of solvent
We know that the mass of the solvent is the same as the mass of the solution, since the volume of the solvent did not change. So, the mass of the solvent is:
Mass of solvent = mass of solvent + mass of solute
Mass of solvent = / 1000
Mass of solvent =
Now we can calculate the molality:
Molality = moles of solute / kilograms of solvent
Molality = /
Molality =
The molality of the student's solution is 0.246 m.
In summary, the student's solution has a molarity of 0.169 M and a molality of 0.246 m.
for more such questions on molarity .
https://brainly.com/question/30404105
#SPJ11
the iron (iii) phenanthroline complex ion will be made during this experiment the phenanthroline ligand is classified as a bidentate ligand which means select one: the phenanthroline ligand bonds to two fe3 metal cations. two phenanthroline ligands bond to one fe3 cation. the ligand forms two bonds with the fe3 cation.
The iron (iii) phenanthroline complex ion will be made during this experiment the phenanthroline ligand is classified as a bidentate ligand which means : "the ligand forms two bonds with the Fe3+ cation."
A bidentate ligand is a molecule or an ion that can form two coordinate bonds with a metal ion. In the case of the iron (III) phenanthroline complex ion, the phenanthroline ligand (C12H8N2) can bind to the Fe3+ cation through two nitrogen atoms, each forming a coordinate covalent bond. Therefore, the ligand forms two bonds with the Fe3+ cation, making it a bidentate ligand.
A bidentate ligand is a molecule or ion that can form two coordinate bonds with a metal ion. In the case of the iron (III) phenanthroline complex ion, the phenanthroline ligand (C12H8N2) forms two coordinate covalent bonds with the Fe3+ cation, making it a bidentate ligand.
To know more about the phenanthroline ligand refer here :
https://brainly.com/question/28304982#
#SPJ11
Some parts of the electromagnetic spectrum can cause changes in biological cells due to the energy of each photon: For the wavelengths given for different bands, determine the energy of a single photon, indicate if it can break the atomic bond of water (4.7 eV), ionize hydrogen (13.6 eV), and ionize calcium (6.11 eV): For those that can break bonds, how many molecules/atoms can one photon change? Show all of your work, not just vour answers in the table: Band Microwave Infrared Green Ultraviolet X-ray Break HzO lonize H lonize Ca 5 cm 50 um 500 nm 10 nm 50 pm
One UV photon can break the atomic bond of almost one water molecule. However, it is important to note that the actual number of molecules/atoms that can be changed by one photon depends on several factors, such as the intensity and duration of the exposure.
The energy of a single photon can be calculated using the equation E = hv, where E is energy, h is Planck's constant, and v is frequency.For the given bands, the energy and other properties of a single photon are:Microwave: [tex]2.42 * 10^{-23} J[/tex], cannot break the atomic bond of water or ionize hydrogen or calcium.Infrared: [tex]1.98 * 10^{-19} J[/tex], cannot break the atomic bond of water or ionize hydrogen or calcium.Green: [tex]3.95 * 10^{-19} J[/tex], cannot break the atomic bond of water or ionize hydrogen or calcium.Ultraviolet: [tex]7.86 * 10^{-19} J[/tex], can break the atomic bond of water, cannot ionize hydrogen or calcium.X-ray: [tex]3.98 * 10^{-15} J[/tex], can break the atomic bond of water and ionize both hydrogen and calcium.To calculate the number of molecules/atoms that one photon can change, we can divide the energy required to break a bond/ionize an atom by the energy of one photon. For example, for water:Energy required to break atomic bond: [tex]4.7 eV = 7.54 * 10^{-19} J[/tex]Energy of one UV photon: [tex]7.86 * 10^{-19} J[/tex]Number of water molecules changed per photon: [tex]7.54 * 10^{-19} J / 7.86 * 10^{-19} J = 0.96[/tex]Therefore, one UV photon can break the atomic bond of almost one water molecule. However, it is important to note that the actual number of molecules/atoms that can be changed by one photon depends on several factors, such as the intensity and duration of the exposure.For more such question on photon
https://brainly.com/question/27856390
#SPJ11