If a spacecraft is moving at 20,000 mph (in space), it will continue to move at 20,000 mph when its engines shut off.
The law that explains this is Newton's first law of motion.
Newton's first law of motion, also known as the law of inertia, states that an object at rest will stay at rest, and an object in motion will continue in motion with the same speed and direction, unless acted upon by an external force.
In the case of the spacecraft moving at 20,000 mph, it will continue to move at that speed when its engines shut off, because there are no external forces acting upon it in the vacuum of space.
To know more about Newton's first law of motion:
https://brainly.com/question/974124
#SPJ11
a 1 540-kg automobile has a wheel base (the distance between the axles) of 3.10 m. the automobile's center of mass is on the centerline at a point 1.10 m behind the front axle. find the force exerted by the ground on each wheel.
The force exerted by the ground on each wheel of the automobile is 7560.3 N, which is half of the weight of the car.
How to find the force exerted by the ground on each wheel?Since the center of mass is located 1.10 m behind the front axle, the distance between the center of mass and the rear axle is 3.10 m - 1.10 m = 2.00 m.
The weight of the automobile acts vertically downward through its center of mass and is given by:
W = mg
where
m = mass of the automobile
g = acceleration due to gravity = 9.81 m/s^2
Substituting the given values:
W = (1540 kg) * (9.81 m/s^2) = 15120.6 N
Assuming the weight is evenly distributed between the two wheels, the force exerted by each wheel can be found by considering the torque equilibrium of the automobile about the rear axle.
Since the automobile is in static equilibrium, the sum of the torques about any point is zero. Taking the rear axle as the pivot point, the torque due to the weight of the automobile is counteracted by the torques due to the forces exerted by the ground on the two wheels.
Let F1 and F2 be the forces exerted by the ground on the front and rear wheels, respectively. The torques due to these forces can be found using the distance between the wheels and the center of mass:
τ1 = F1 * 1.10 m (clockwise torque)
τ2 = F2 * 2.00 m (counterclockwise torque)
Since the automobile is in torque equilibrium, we have:
τ1 + τ2 = 0
Substituting the values and solving for F1 and F2:
F2 = (τ1/2.00 m) = (W/2) = 7560.3 N
F1 = (τ2/1.10 m) = (W/2) = 7560.3 N
Therefore, the force exerted by the ground on each wheel is 7560.3 N.
Learn more about Center of mass
brainly.com/question/28996108
#SPJ11
Based on the Doppler effect, the electromagnetic waves reaching Earth from a galaxy that is moving away from Earth would be
expected to
O experience an increase in frequency.
O experience a decrease from transverse waves to longitudinal waves.
O experience a decrease in frequency
O experience an increase in their amplitude.
7
8
9 10 11 12 13 14 15 16 Next
Based on the Doppler effect, the electromagnetic waves reaching Earth from a galaxy that is moving away from Earth would experience a decrease in frequency.
option C.
What is Doppler effect?The Doppler effect is a phenomenon where the frequency of waves (such as electromagnetic waves or sound waves) is shifted as a result of the relative motion between the source of the waves and the observer. When a source of waves is moving away from an observer, the waves get stretched out, resulting in a decrease in frequency. This is known as redshift for light waves, which are a type of electromagnetic waves.
In the context of a galaxy moving away from Earth, the electromagnetic waves (such as light) emitted by the galaxy would experience a redshift, which means the frequency of the waves would decrease. This is a key observation in astronomy and cosmology that has been used to provide evidence for the expanding universe and the Big Bang theory, as galaxies in the universe are generally observed to be moving away from each other, causing their light to be redshifted.
Learn more about doppler effect here: https://brainly.com/question/3841958
#SPJ1
voyager 1 is a space probe launched by nasa in 1977 and is the farthest human-made object. it experiences negligible gravity. voyager 1 is propelled by thrusters but will run out of fuel by 2040. what will happen to voyager 1 after this date?multiple select question.the velocity of voyager 1 will remain unchanged.voyager 1 will slow down from the velocity it will have when the fuel runs out.voyager 1 will immediately stop.voyager 1 will continue moving with the speed it will have when the fuel runs out.
Voyager 1 will continue moving with the speed it will have when the fuel runs out. The probe is traveling through the vacuum of space, where there is negligible gravity and no significant air resistance to slow it down.
Without the ability to adjust its trajectory, Voyager 1 will continue on its current path indefinitely unless it encounters a gravitational field that alters its trajectory. The probe may eventually drift off course and potentially collide with other celestial objects in its path. While Voyager 1 will continue to communicate data to Earth until its systems eventually fail, it will eventually become just another piece of space debris, floating silently through the cosmos.
Learn more about Voyager 1
https://brainly.com/question/3412409
#SPJ4
imagine that two identical asteroids crashed into the same type of rocks on the surface of the moon and earth. both impacts produce craters. how will the craters compare?
The crater on the moon will be more well-preserved than the crater on the Earth.
The main reason for this is the lack of atmosphere on the moon. On Earth, the atmosphere absorbs some of the energy from the impact, reducing the severity of the crater. Additionally, erosion from wind and water can also affect the appearance of the crater on Earth. On the moon, however, there is no atmosphere to absorb the energy from the impact, so the crater will retain its original shape and size for a longer period of time.
The moon also lacks the same degree of erosion processes as Earth. As a result, the craters formed on the moon are often well-preserved and can be used to study the history of impacts on the lunar surface.
To learn more about crater on the moon, here
https://brainly.com/question/24409142
#SPJ4
Earth's sky is blue during the day because:a. the molecules in the atmosphere scatter blue wavelengths of lightb. the atmosphere absorbs blue wavelengths of lightc. the sun produces more blue wavelengths than it produces in any other colord. red wavelengths are lost as solar radiation passes through the vacuum of space
The molecules in the Earth's atmosphere scatter blue wavelengths of light, making the sky appear blue during the day. The correct answer is a.
This phenomenon is known as Rayleigh scattering, which occurs when sunlight enters the Earth's atmosphere and interacts with the gas molecules in the air. The shorter, blue wavelengths of light are more easily scattered by the molecules in the atmosphere, while the longer, red wavelengths are less affected and continue to travel in a more direct path.
As a result, when we look up at the sky during the day, we see a blue color because the blue light is being scattered in all directions by the atmosphere. At sunrise and sunset, the sky appears more orange or red because the sun's light has to travel through more of the atmosphere, causing more scattering of the shorter, blue wavelengths and leaving more of the longer, red wavelengths to reach our eyes.
Learn more about Earth's atmosphere
https://brainly.com/question/13154099
#SPJ4
when a fan is turned off, its angular speed decreases from 10 rad/s to 4.4 rad/s in 2.50 s. what is the magnitude of the average angular acceleration of the fan? a. 0.86 rad/s2 b. 2.24 rad/s2 c. 0.37 rad/s2 d. 11.0 rad/s2 e. 1.20 rad/s2
The magnitude of the average angular acceleration of the fan is 2.24 rad/s2 . So the correct answer is option: b.
The average angular acceleration can be calculated using the formula:
average angular acceleration = (final angular speed - initial angular speed) / time
Plugging in the given values, we get:
average angular acceleration = (4.4 rad/s - 10 rad/s) / 2.50 s
average angular acceleration = -2.56 rad/s2
Note that the negative sign indicates that the angular acceleration is in the opposite direction to the initial angular velocity.
|average angular acceleration| = 2.56 rad/s2 ≈ 2.24 rad/s2 .
Therefore, the correct answer is (b).
To know more about magnitude, here
brainly.com/question/14452091
#SPJ4
The __________ notation of entity-relationship modelling can be used for both conceptual and implementation modelling.
a. Bachman
b. UML
c. Chen
d. Crow's Foot
The Chen notation of entity-relationship modelling can be used for both conceptual and implementation modelling.
The Chen notation of entity-relationship modelling can be used for both conceptual and implementation modelling. Notation refers to the symbols and conventions used to represent concepts in a model. Entity-relationship modelling is a technique used in database design to represent the relationships between entities. Conceptual modelling is the process of creating a high-level representation of a system, while implementation modelling involves creating a detailed representation of the system's implementation.
To learn more about Chen notation Here:
https://brainly.com/question/28234454
#SPJ11
Modern geologists have abandoned relative dating methods in favor of more precise absolute dating methods. True/False
False. Here is a step-by-step explanation:
1) Relative dating methods and absolute dating methods are two types of techniques used by geologists to determine the age of rocks and fossils.
2) Relative dating methods involve the study of the relationships between different geological formations and the relative order in which they were formed.
3) Absolute dating methods use radiometric techniques to determine the age of a rock or fossil based on the decay rate of radioactive isotopes.
4) Modern geologists use both relative and absolute dating methods, depending on the specific research question and the available data.
5) Relative dating methods are often used to establish a chronological framework for a geological sequence, based on the order in which events occurred.
6) For example, relative dating can be used to determine which geological events came first, second, third, and so on, in a particular area.
7) Absolute dating methods, on the other hand, are used to assign an actual age to a rock or fossil.
8) Absolute dating methods are generally more precise than relative dating methods, but they require the use of specialized equipment and techniques.
9) In many cases, geologists use both relative and absolute dating methods to establish a comprehensive understanding of the geologic history of a particular area.
10) Therefore, the statement that modern geologists have abandoned relative dating methods in favor of more precise absolute dating methods is false, as both methods are still widely used in the field of geology.
To know more about Modern geologists :
https://brainly.com/question/28274168
#SPJ11
a projectile of mass 1.3 kg is launched horizontally from an initial height 2.9 m with an initial velocity 8.5 m/s. this velocity in the x direction is preserved when you ignore air resistance. the projectile still accelerates in the vertical y direction toward the ground, but this is exactly the energy lost from potential energy. energy is conserved as long as you use the total mechanical energy equation. what is the total final kinetic energy (joules) as the projectile just reaches the ground? give your numerical answer to one decimal place precision. assume g
The total final kinetic energy of the projectile as it reaches the ground is 49.5 J (to one decimal place of precision).
Applying conservation of energyTo solve this problem, we need to use the conservation of energy principle. The initial total mechanical energy (potential plus kinetic) of the projectile is converted into its final total mechanical energy when it reaches the ground, assuming no energy is lost due to air resistance.
The initial potential energy is given by:
Ep = mgh = (1.3 kg)(9.81 m/s^2)(2.9 m) = 36.01 J
The initial kinetic energy in the x-direction is given by:
Kx = 0.5mvx^2 = 0.5(1.3 kg)(8.5 m/s)^2 = 49.47 J
Since there is no initial kinetic energy in the y-direction, the total initial mechanical energy is the sum of the initial potential and kinetic energies in the x-direction:
Ei = Ep + Kx = 36.01 J + 49.47 J = 85.48 J
At the final moment, the projectile reaches the ground, so its final potential energy is zero. Therefore, the final total mechanical energy is equal to the final kinetic energy:
Ef = Kf
We know that the projectile is subject to constant acceleration due to gravity (9.81 m/s^2) in the y-direction, and we can use the kinematic equation:
y = yo + voyt + 0.5a*t^2
where y is the final position (0 m), yo is the initial position (2.9 m), voy is the initial velocity in the y-direction (0 m/s), a is the acceleration due to gravity (-9.81 m/s^2), and t is the time it takes for the projectile to reach the ground.
Rearranging this equation to solve for t, we get:
t = sqrt(2(y - yo)/a) = sqrt(2(0 - 2.9)/(-9.81)) = 0.762 s
Now we can use the final velocity in the x-direction and the time of flight to calculate the final kinetic energy in the x-direction:
Kxf = 0.5mvx^2 = 0.5(1.3 kg)(8.5 m/s)^2 = 49.47 J
Therefore, the final total mechanical energy and final kinetic energy are:
Ef = Kf = Kxf = 49.47 J
Therefore, the total final kinetic energy of the projectile as it reaches the ground is 49.5 J (to one decimal place of precision).
Learn more on kinetic energy here https://brainly.com/question/8101588
#SPJ1
mine C contient 1000 mg
d'acide ascorbique. Il
se prend dans un verre
d'eau de 20 CL.
1. Une orange contient
115 mg d'acide ascorbique. Combien faut-il d'oranges
pour obtenir la même masse d'acide ascorbique que
le comprimé ?
2. Il faut environ trois oranges pour obtenir 200 mL de
jus. Quelle est la concentration en acide ascorbique
du jus d'orange ?
3. Quel volume de la solution obtenue avec le comprimé
dans le verre contient la même masse d'acide ascor-
bique que ces trois oranges ?
4. Quel volume d'eau faut-il ajouter au verre contenant
le comprimé pour obtenir la même concentration en
acide ascorbique que le jus d'orange ?
Answer:
Explanation: honestly i don’t speak spanish so please explain with english
How much heat does it take to raise the temperature of 5.0 kg of plastic from 15°C to 75°C? The specific heat of plastic is 2.60 kJ/(kg × °C).
where
m is the mass
c is the specific heat capacity
ΔT is the change in temperature
In your problem,
m=2.5 kg
c=2.60 kJ⋅°C-1kg-1
Δ
∴ q=2.5kg×2.60 kJ⋅°C-1⋅kg-1×60°C=390 kJ
A student collected the data below on the time and distance traveled by a beetle.
Flight of a Beetle
OB. 1 m/s
O C. 1.25 m/s
Distance in meters (m)
OD. 4 m/s
€5.0
4.0
1.0 2.0 3.0 4.0 5.0
Time in seconds (s)
What was the beetle's average flight speed during the time represented in the graph?
O A. .75 m/s
3.0
2.0
1.0
Answer: the correct answer is option C) 1.25 m/s.
Explanation: The formula for average speed can be expressed as the quotient of the total distance traveled divided by the total time elapsed.
Upon examination of the presented graphical representation, it is evident that the beetle traversed a cumulative distance of 5 meters within a duration of 4 seconds.
Thus, it can be observed that the mean velocity of the beetle would be:
The mean velocity of the object is 5 meters per 4 seconds.
The mean velocity is equivalent to 1.25 meters per second.
The data depicted in the aforementioned graph indicates that the average velocity of the beetle during its flight is 1.25 meters per second.
The tire had an initial volume of 7 liters, at a temperature of 25° C. After driving for an hour, friction from the road had increased the temperature of air in the tire to 35° C. Assuming the pressure inside the tire did not change, what would the tire’s new volume be?
Answer:
using
V2= V1T2/T1
V2= 9.8L
An inductor is connected to a 20 kHz oscillator that produces an rms voltage of 9.0 V. The peak current is 60 mA. What is the value of the inductance L? Final answer in mH. Please explain step by step.
The value of the inductance L is approximately 1193.25 mH.
To solve for the value of the inductance L, we can use the formula:
Vrms = Ipeak * (2 * pi * f * L)
where:
Vrms = 9.0 V
Ipeak = 60 mA = 0.06 A
f = 20 kHz
Substituting the values into the formula:
9.0 V = 0.06 A * (2 * pi * 20,000 Hz * L
Simplifying:
L = 9.0 V / (0.06 A * 2 * pi * 20,000 Hz)
L = 9.0 / (0.007536)
L = 1193.25 mH (rounded to two decimal places)
Therefore, the value of the inductance L is approximately 1193.25 mH.
Learn more about inductance L
https://brainly.com/question/20471259
#SPJ4
An inductor is connected to a 20 kHz oscillator that produces an RMS voltage of 9.0 V. The peak current is 60 mA. The value of the inductance L is 1.692 mH.
Let's start by using the given information and then we'll solve for the value of the inductance L step by step:
1. Frequency of the oscillator (f) = 20 kHz = 20,000 Hz
2. RMS voltage (Vrms) = 9.0 V
3. Peak current (I_peak) = 60 mA = 0.06 A
Now, let's find the peak voltage (V_peak) using the relationship between RMS voltage and peak voltage:
Vrms = V_peak / √2
V_peak = Vrms * √2
V_peak = 9.0 V * √2 ≈ 12.73 V
Next, we'll calculate the impedance (Z) of the inductor using Ohm's law, which relates peak voltage and peak current:
Z = V_peak / I_peak
Z ≈ 12.73 V / 0.06 A ≈ 212.17 Ω
Now, we'll use the formula for the impedance of an inductor:
Z = 2 * π * f * L
Let's solve for the inductance L:
L = Z / (2 * π * f)
L ≈ 212.17 Ω / (2 * π * 20,000 Hz)
L ≈ 1.692 × 10^-3 H
Finally, convert the inductance L to millihenries (mH):
L ≈ 1.692 mH
So, the value of the inductance L is approximately 1.692 mH.
To learn more about inductor, refer:-
https://brainly.com/question/15893850
#SPJ11
3. When the procedure is repeated with a third line how will it distinguish whether the location of the center of gravity is accurate or not?
If the procedure is repeated with a third line, it will distinguish whether the location of the center of gravity is accurate or not by checking if the intersection point of the three lines passes through the same point as the previous two lines.
This is because the intersection of the third line with the other two lines should also pass through the same point as the previous two lines if the location of the center of gravity is accurate. If the intersection point of the third line is not consistent with the previous two, then it suggests that the location of the center of gravity is not accurate.
To know more about intersection point , here
brainly.com/question/14217061
#SPJ4
the value of the total radiant energy flux density at the earth from the sun normal to the incident rays is called the solar constant of the earth. the observed value integrated over all emission wavelengths and referred to the mean earth-sun distance is:
The observed value of the total radiant energy flux density at the earth from the sun, integrated over all emission wavelengths and referred to the mean earth-sun distance, is approximately 1,366 watts per square meter.
This value is known as the solar constant and is an important factor in understanding the earth's climate and energy balance. It represents the amount of solar energy that is received per unit area at the top of the earth's atmosphere and is a key input for models of global climate change.
Learn more about energy flux
https://brainly.com/question/30480603
#SPJ4
in terms of db , how much louder will the more powerful amplifier be when both are producing sound at their maximum levels?
The increase in decibels (dB) when comparing the more powerful amplifier to the less powerful one will depend on the specific amplifiers being compared. Generally, a doubling of amplifier power will result in a 3dB increase in sound output.
Therefore, if the more powerful amplifier is twice as powerful as the less powerful one, it will produce a 3dB increase in sound output when both are producing sound at their maximum levels. However, if the difference in power between the two amplifiers is greater or less than a factor of two, the increase in dB will be different.
1. Decibels (dB): A logarithmic unit used to express the ratio of two values of a physical quantity, often used to measure sound levels.
2. Amplifier: An electronic device that increases the power of a signal, typically used for audio purposes.
3. Sound Pressure Level (SPL): A measure of the sound pressure of a sound wave relative to a reference value, usually expressed in decibels (dB).
Now, let's go through the steps to compare the loudness of two amplifiers at their maximum levels:
Find the power output (in watts) of both amplifiers at their maximum levels. You'll need this information to proceed with the calculation.
Calculate the difference in decibels (dB) between the two amplifiers using the following formula:
dB difference = 10 * log10(Power Amplifier 1 / Power Amplifier 2)
Where Power Amplifier 1 and Power Amplifier 2 are the power outputs of the two amplifiers in watts.
Interpret the result. A positive dB difference indicates that Amplifier 1 is louder than Amplifier 2, while a negative dB difference indicates that Amplifier 2 is louder. The larger the absolute value of the dB difference, the greater the difference in loudness between the two amplifiers.
More on amplifier: https://brainly.com/question/26252359
#SPJ11
a horizontal force of 80 n used to push a chair across a room does 320 j of work. how far does the chair move in this process?
The amount of work done by the force of 80 n is 320 j. Work is calculated by multiplying the force (F) by the distance (d) moved. Therefore, d = 320/80 = 4 m. This means that the chair moved 4 m in the process.
Energy is transformed into work when it takes another form.
In this instance, the chair is being moved across the room by the force of 80 n, which is transmitting its energy to it as labour. In joules (J), this energy is expressed.
As a result, the work produced by the force of 80 n is equivalent to the 320 J of energy that was transmitted. This quantity of energy is equivalent to the 4 m that the chair has travelled.
Complete Question:
A horizontal force of 80 n used to push a chair across a room does 320 j of work. How far does the chair move in this process?
To learn more about work visit:
https://brainly.com/question/25573309
#SPJ4
seamus made an electromagnet from an iron nail, a piece of copper wire with three coils spread out across the nail, and a aaa-sized battery. he's magnet attracts only one paper clip, and he wants to boost the power of his magnet to attract at least four paper clips. what two things can seamus do to accomplish his goal? responses seamus can add batteries to decrease the voltage, and he can increase the space between the wire coils. seamus can add batteries to decrease the voltage, and he can increase the space between the wire coils. seamus can add batteries to increase the voltage, and he can decrease the space between the wire coils. seamus can add batteries to increase the voltage, and he can decrease the space between the wire coils. seamus can add batteries to decrease the voltage, and he can decrease the space between the wire coils. seamus can add batteries to decrease the voltage, and he can decrease the space between the wire coils. seamus can add batteries to increase the voltage, and he can increase the space between the wire coils. seamus can add batteries to increase the voltage, and he can increase the space between the wire coils.
Seamus can add batteries to increase the voltage, and he can decrease the space between the wire coils.
This will increase the magnetic field strength and attract more paper clips. Another option would be to add more coils to the wire, which would increase the magnetic field strength as well. Seamus can add batteries to increase the voltage, and he can decrease the space between the wire coils. By doing these two things, he will be able to boost the power of his electromagnet and attract at least four paper clips.
More on voltage: https://brainly.com/question/13863356
#SPJ11
another capacitor, identical to the original, is added in series to the circuit described in the passage. compared to the original circuit, the equivalent capacitance of the new circuit is:
The equivalent capacitance of the new circuit with an identical capacitor added in series is half of the original circuit's capacitance.
When a second capacitor, identical to the original, is added in series to the circuit, the equivalent capacitance of the new circuit is reduced. This is because the total capacitance in a series circuit is always less than the individual capacitances. The formula for calculating the equivalent capacitance of a series circuit is:
[tex]1/Ceq = 1/C1 + 1/C2 + ... + 1/Cn[/tex]
Where C1, C2, ..., Cn are the capacitances of the individual capacitors.
Adding another capacitor in series to the circuit means that the equivalent capacitance will be smaller, and the total charge stored in the circuit will be less. This will affect the behavior of the circuit when connected to a voltage source, as it will take less time to charge and discharge.
Learn more about circuit's capacitance.
https://brainly.com/question/28884207
#SPJ4
if one-third of this energy goes into heat and other forms of internal energy of the motor, with the rest going to the motor output, how much torque will this engine develop if you run it at 2400 rpm ?
The engine will develop a torque of 475.47 N·m when run at 2400 rpm.
The torque developed by an engine can be calculated using the formula:
Torque = Power / (2π × RPM / 60)
where power is the net power output of the engine and RPM is the speed of the engine in revolutions per minute.
Given that the engine produces 75 kW of power, one-third of which goes into heat and other forms of internal energy, the net power output would be:
Net power = 75 kW × (1 - 1/3) = 50 kW
Converting the engine speed of 2400 rpm to radians per second gives:
ω = 2400 rpm × (2π / 60) = 251.33 rad/s
Substituting the values into the torque formula:
Torque = 50,000 W / (2π × 251.33 / 60) = 475.47 N·m
Learn more about internal energy, https://brainly.com/question/14668303
#SPJ4
to resolve two point sources, what distribution of cones must occur where the image strikes the retina?
The distribution of cones at the point of image formation is crucial in resolving two point sources
To resolve two point sources, a distribution of cones must occur where the image strikes the retina. Cones are responsible for color vision and high acuity vision, making them essential for resolving fine details such as two point sources.
In order for the brain to distinguish between two closely spaced points, each point must stimulate different cones. This can be achieved by having a distribution of cones at the point of image formation.
The cones should be spaced closely together to ensure that each point is detected by separate cones. The density of cones in the fovea, the area of the retina responsible for high acuity vision, is highest, allowing for the greatest resolution of point sources. .
To learn more about : distribution
https://brainly.com/question/28027633
#SPJ11
after the switch s is closed, what will be the current in the circuit at the instant that the capacitors have lost 80.0% of their initial stored energy?
After switch S is closed, the capacitors in the circuit start to discharge.
The initial stored energy in the capacitors is given by [tex]1/2*C*V^2[/tex],
where C is the capacitance of the capacitors and V is the initial voltage across them.
As the capacitors discharge, the voltage across them decreases and so does the stored energy.
When the capacitors have lost 80.0% of their initial stored energy, the voltage across them will be 0.447 times the initial voltage.
At this point, the current in the circuit can be calculated using Ohm's law, which states that the current is equal to the voltage divided by the total resistance of the circuit.
Therefore, the current in the circuit at this point can be calculated as I = V/R, where V is the voltage across the capacitors and R is the total resistance of the circuit.
For more such answers on Capacitance
https://brainly.com/question/16998502
#SPJ11
waves on a particular string travel with a velocity of 10 m/s. a high-speed photograph shows that successive peaks are 0.50 m apart along the string. the frequency of the waves is:
The frequency of the waves on the string is 20 Hz.
The velocity of waves on a string is given by the equation:
v = λf
where v is the velocity of the wave, λ is the wavelength, and f is the frequency of the wave.
We are given that the velocity of waves on the string is 10 m/s and that successive peaks (or troughs) are 0.50 m apart. This distance is equal to the wavelength (λ) of the wave. Therefore, we can write:
λ = 0.50 m
Substituting this value and the given velocity into the equation above, we get:
10 m/s = (0.50 m) f
Solving for f, we get:
f = 10 m/s / 0.50 m = 20 Hz
To know more about Velocity:
https://brainly.com/question/30559316
#SPJ4
A compound microscope is a two-lens system used to look at very small objects. Which of the following statements is correct? The objective lens is a short focal length, convex lens and the eyepiece functions as a simple magnifier. The objective lens is a long focal length, convex lens and the eyepiece functions as a simple magnifier. The objective lens and the eyepiece both have the same focal length and both serve as simple magnifiers. The objective lens is a short focal length, concave lens and the eyepiece functions as a simple magnifier. The objective lens is a long focal length, concave lens and the eyepiece functions as a simple magnifier.
The objective lens is a long focal length, convex lens and the eyepiece functions as a simple magnifier is the correct statement about a compound microscope. Option b is correct.
In a compound microscope, the objective lens is a long focal length, convex lens that produces an inverted, magnified real image of the specimen. The eyepiece, on the other hand, functions as a simple magnifier, which further magnifies the real image produced by the objective lens and forms a virtual image that can be viewed by the observer's eye. Therefore, option b is the correct statement.
To know more about microscope, here
brainly.com/question/18661784
#SPJ4
--The complete question is, A compound microscope is a two-lens system used to look at very small objects. Which of the following statements is correct?
a. The objective lens is a short focal length, convex lens and the eyepiece functions as a simple magnifier.
b. The objective lens is a long focal length, convex lens and the eyepiece functions as a simple magnifier.
c. The objective lens and the eyepiece both have the same focal length and both serve as simple magnifiers.--
what do you call a bar optic where there isn't an amount and it starts when pressure is applied and stops when it is released
The type of bar optic you are describing is commonly known as a "free flow pourer" or "free pour spout."
These types of pourers do not have a specific amount they dispense but instead rely on the bartender's skill to regulate the flow of liquid by applying and releasing pressure on the bottle. The flow of liquid stops when pressure is released, allowing for precise and controlled pouring.
Free flow pourers are commonly used in bars and restaurants to pour spirits, mixers, and other liquids into cocktails and drinks. They can come in a variety of sizes and materials, including plastic, metal, and silicone, and are easily replaceable when worn or damaged.
Learn more about bar optic
https://brainly.com/question/30694096
#SPJ4
based on the reading of the geiger counter, which type of radiation do you think is primarily emitted from the fiesta ware plate?
Based on the reading of the Geiger counter, it is likely that the Fiesta Ware plate is emitting beta radiation.
Beta radiation consists of high-energy electrons or positrons that can penetrate through skin and clothing but can be stopped by a thin sheet of metal. This type of radiation is commonly emitted by radioactive materials such as strontium-90, which was often used in the production of Fiesta Ware.
Beta radiation (β) is the transmutation of a neutron into a proton and an electron (followed by the emission of the electron from the atom's nucleus: e − 1 0 ). When an atom emits a β particle, the atom's mass will not change (because there is no change in the total number of nuclear particles).
To know more about Beta Radiation, please click:
brainly.com/question/16645044
#SPJ11
A 55 kg skater is gliding along the ice at a velocity of 8 m/s to the right while holding a 3 kg ball. The skater throws the ball at a velocity of 4 m/s to the right. What will be the skaters velocity after throwing the ball?
Answer:
Speed of Skater = 8.16 m/s
Explanation:
Using kinetic energy:
[tex]M_{t} = M_{skater} + m_{ball}\\\frac{1}{2}M_{t}V_{i}^2 = \frac{1}{2}*M*V_{s} ^2+\frac{1}{2}*m*V_{b}^2\\ M_{t}V_{i}^2 = M_{s}*V_{s} ^2+m_{b}*V_{b}^2\\M_{t}V_{i}^2-m_{b}*V_{b}^2 = M_{s}*V_{s} ^2\\(M_{t}V_{i}^2-m_{b}*V_{b}^2)/M_{s} = V_{s} ^2\\V_{s} = \sqrt{\frac{(M_{t}V_{i}^2-m_{b}*V_{b}^2)}{M_{s}} } \\[/tex]
This gives the skater a velocity of 8.16 m/s after throwing the ball
in a(n) ____ joint the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.
In a butt joint, the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.
In a butt joint, the edges of the metal pieces are placed together so that they are flush with one another, with little or no overlap. This results in a joint where the thickness of the joint is approximately equal to the thickness of the metal being joined. Butt joints are commonly used in welding and metal fabrication, as they provide a clean, simple joint that can be easily welded or brazed together. However, they may not be as strong as other types of joints, such as lap joints or T-joints, which provide more surface area for welding or brazing.
To learn more about metals, refer:-
https://brainly.com/question/28650063
#SPJ11
In welding, a joint refers to the area where two pieces of metal are joined together. There are several types of joints used in welding, including butt joints.
A butt joint is formed when two pieces of metal are placed together, edge to edge, and welded.
The joint is formed so that the thickness of the joint is approximately equal to the thickness of the metal being joined.
The process of making a butt joint involves
1) first preparing the edges of the metal.
2) This may involve grinding or filing to ensure that the edges are clean and straight.
3) The two pieces of metal are then brought together, with their edges touching, and held in place using clamps or other devices.
4) Once the pieces are in place, a welding machine is used to fuse the metal together.
The welding process may involve the use of heat or pressure, or a combination of both, depending on the type of welding being used.
The resulting joint is strong and durable, and is often used in a variety of applications where a strong, seamless joint is needed.
Butt joints are commonly used in the construction of buildings, bridges, and other structures, as well as in the manufacturing of machinery and equipment.
To know more about butt joint visit link :
https://brainly.com/question/31733313
#SPJ11
what is the largest x-ray wavelength that can be diffracted by crystal planes with a separation of 0.316 nm?
The largest x-ray wavelength that can be diffracted by crystal planes with a separation of 0.316 nm is 0.632 nm.
To find the largest X-ray wavelength that can be diffracted by crystal planes with a separation of 0.316 nm, we can use Bragg's Law:
nλ = 2d sinθ
where n is an integer representing the order of diffraction, λ is the wavelength, d is the separation between crystal planes (0.316 nm), and θ is the angle of incidence. To find the largest possible wavelength, we need to consider the lowest order of diffraction (n = 1) and the maximum angle of incidence (θ = 90°).
Now we can plug in the values and solve for λ:
1λ = 2(0.316 nm) sin(90°)
λ = 2(0.316 nm) * 1
λ = 0.632 nm
The largest X-ray wavelength that can be diffracted by crystal planes is 0.632 nm.
Learn more about Bragg's Law:
https://brainly.com/question/14617319
#SPJ11