The magnitude of the particle's acceleration is 0.202 m/s² and its direction is upward (in the positive z-direction).
The force on a moving charged particle in a magnetic field is given as follows:
F= q×v
Therefore, the acceleration of the charged particle is given as follows:
ā = q/m (v×B)
F = [tex]{(1.22*10^-8 C)(3.00*10^4 m/s)j^}*(1.63T)i^ + (0.980T)j^[/tex]
F= (3.66×10^-4 N)k^
F= ma
a=[tex]\frac{F}{m}[/tex] = [tex]\frac{(3.66*10^-4 N)}{(1.81*10^-3 kg)}[/tex] = 0.202 m/s²
Acceleration is an important concept in physics and is used to describe the behavior of objects in motion. The magnitude of the acceleration is measured in units of meters per second squared (m/s²) in the International System of Units (SI).
An object accelerates when there is a net force acting upon it. This net force can be caused by many factors such as gravity, friction, or applied forces. If the net force is in the same direction as the object's velocity, the object will speed up; if it is in the opposite direction, the object will slow down. If the direction of the force is perpendicular to the direction of the velocity, the object's path will curve.
To learn more about Acceleration visit here:
brainly.com/question/3046924
#SPJ4
James put a pot of liquid water on the hot stove. When he came back the liquid was gone. Show why the water changed phase
a message signal has a bandwidth of 30 khz. efficient radiation from an antenna requires that the antenna length be at least a tenth of the transmitted signal wavelength. determine the minimum antenna length for efficient radiation if: (a) it is to be broadcast without the benefit of modulation, (b) it is broadcast after it is amplitude-modulated with a sinusoidal carrier having a frequency that is 100 times the bandwidth of the message signal
The minimum antenna length for efficient radiation if it is to be broadcast without the benefit of modulation is 2000 meters and broadcast after it is amplitude-modulated with a sinusoidal carrier having a frequency that is 100 times the bandwidth of the message signal is 9.87 meters.
To determine the minimum antenna length for efficient radiation, we need to calculate the wavelength of the transmitted signal first.
(a) The given bandwidth of the signal is 30 kHz, which means that the signal occupies a frequency range from f - 15 kHz to f + 15 kHz,
where f is the center frequency of the signal.
Since the signal is broadcast without modulation, its bandwidth is equal to its frequency, so the center frequency is 15 kHz.
The minimum antenna length for efficient radiation is given by: Antenna Length = (1/10) x Wavelength
where Wavelength = Speed of light / Frequency
The speed of light is approximately 3 x 10⁸ meters per second.
Therefore, the wavelength of the signal is:
Wavelength = Speed of light / Frequency = 3 x 10⁸ / 15,000 = 20,000 meters
The minimum antenna length for efficient radiation is then:
Antenna Length = (1/10) x Wavelength = (1/10) x 20,000 = 2000 meters
Therefore, the minimum antenna length for efficient radiation without modulation is 2000 meters.
(b) The message signal is amplitude-modulated with a sinusoidal carrier having a frequency that is 100 times the bandwidth of the message signal.
This means that the carrier frequency is 100 x 30 kHz = 3 MHz.
The bandwidth of the transmitted signal is then the sum of the carrier frequency and the message signal bandwidth, which is 3 MHz + 30 kHz = 3.03 MHz.
Using the same formula as in part (a), we can calculate the wavelength of the transmitted signal:
Wavelength = Speed of light / Frequency = 3 x 10⁸ / 3.03 x 10⁶ = 98.68 meters
The minimum antenna length for efficient radiation is then:
Antenna Length = (1/10) x Wavelength = (1/10) x 98.68 = 9.87 meters
Therefore, the minimum antenna length for efficient radiation after modulation with a sinusoidal carrier is 9.87 meters.
The minimum antenna length for efficient radiation without modulation is 2000 meters and the minimum antenna length for efficient radiation after modulation with a sinusoidal carrier is 9.87 meters.
To practice more question about 'antenna length':
https://brainly.com/question/6849706
#SPJ11
A ray of light starting from diamond is incident on the interface separating diamond and water . Draw a labelled diagram to show the refraction of light in this case
Answer & Explanation:
incident ray
|
v
----------
| diamond |
----------
^
|
refracted ray
In this diagram, the incident ray of light is represented by the line pointing downward towards the diamond. The interface between the diamond and water is shown as a horizontal line. The refracted ray of light is represented by the line pointing upward away from the diamond.
When the incident ray of light passes from diamond into water, it will refract or bend due to the change in the speed of light between the two media. The exact angle of refraction depends on the refractive indices of the diamond and water, as well as the angle of incidence.
A ray of light starting from diamond is incident on the interface separating diamond and water is as shown in the figure.
What is refractive index ?When a light is going from medium 1 to medium 2. The refractive index is defined as a ratio of velocity of light in medium 1 to velocity of light in medium 2. Refractive index is the factor which deals with the amount of bending of light. More refractive index means more it will bend in the medium 2. When it is 1 we can say that light has not been bent.
By Snell's law, Refractive index is given by,
sin (i) ÷ sin (r) = μ₂÷μ₁
where i is the the angle of incidence
r is the angle of refraction
μ₂ & μ₁ are refractive index of medium 2 and 1 resp.
Light bends as it passes from diamond to water at an angle due to Refractive index between air and glass.
white light consist of number of colors, each color has its own wavelength. Refractive index of an optical medium changes with the wavelength, therefore each color of white light get splitted from white light this phenomenon is know as dispersion of the light.
Labeled diagram is shown in the figure.
To know more about light click :
https://brainly.com/question/15200315
#SPJ2
urgent needed help please please
Answer:
Distance from center and mass
Explanation:
Gravity force is determined by the distance from the center of the object, and the mass of the object (so distance and time) speed and acceleration have no effect on the gravity
Answer:
The mass of the object and the distance between objects.
Explanation:
The fastest bird is the spine-tailed swift, which
reaches speeds of 171 km/h. Suppose that you wish
to shoot such a bird with a. 22-caliber rifle that fires
a bullet with a speed of 366 m/s. If you fire at the
instant when the bird is 30 m directly overhead, how
many meters ahead of the bird must you aim the
rifle? Ignore gravity in this problem.
We need to aim the rifle 47.154 meters ahead of the bird's current position to intercept its flight path and hit it.
Since we are ignoring gravity, the horizontal velocity of the bullet will remain constant and equal to the muzzle velocity of the rifle, which is 366 m/s.
To hit the bird, we need to aim the rifle ahead of the bird such that the bullet intercepts the bird's flight path at the same point in space where the bird will be when the bullet arrives.
time = distance / velocity
time = 30 m / 366 m/s
time = 0.08197 s
During this time, the bird will have flown a distance equal to its speed multiplied by the time:
distance = speed x time
distance = 171 km/h x (0.08197 s)
distance = 47.154 m
To know more about Gravity:
https://brainly.com/question/14874038
#SPJ4
How can a person sing into a piano and cause a piano wire to vibrate? (1 point)
O The person sings at the same frequency as the piano wire, called the beat frequency.
OThe person sings at a different frequency than the piano wire, called the beat frequency.
OThe person sings at the same frequency as the piano wire, called the resonance frequency.
OThe person sings at a different frequency than the piano wire, called the resonance frequency.
Answer:
The person sings at the same frequency as the piano wire, called the resonance frequency.
Explanation:
The person sings at a different frequency than the piano wire, called as resonance frequency. So, option d is correct.
Interference directs to a phenomenon in which two wires meet while traveling along the exact medium and they superpose to create a resulting wave that is lower, greater, or the same amplitude as each other. The soundboard is a big wooden panel that amplifies the sound of the vibrating string.
In the given scenario, a beat frequency is listened to by a player when using a tuning fork to adjust a piano wire. Thus, the piano tuner should change the strain in the wire, this decreases the frequency of the wire.
A car accelerates from a stop at a rate of 2 m/s² for 20 s, then con- tinues at a constant speed for 40 s. Graph the speed vs. time of the car. What is the car's speed at 10 s? What is its final speed?
The car's speed at 10 s would be 20 m/s, and the final speed would be 40 m/s.
Velocity-time graphDuring the first 20 s, the car accelerates at a rate of 2 m/s², so its speed increases linearly. We can calculate the final speed at 20 s as follows:
a = 2 m/s²
t = 20 s
v = a * t = 2 m/s² * 20 s = 40 m/s
From 20 s to 60 s, the car continues at a constant speed, so the graph is a horizontal line at 40 m/s.
Therefore, the car's speed at 10 s is:
t = 10 s
v = a * t = 2 m/s² * 10 s = 20 m/s
And its final speed is 40 m/s
More on velocity-time can be found here:https://brainly.com/question/19979064
#SPJ1
The torque vs. rotations graph above describes the effects of an increasing unbalanced torque due to a force that acts tangentially along the edge of an object with a moment of Inertia of 0.0025 kg m^2.
Which of the following is the angular velocity of the disc after 2.0 seconds if the disc starts from rest?
The graph is just a torque vs rotations graph. I'm more so looking for an explanation of this.
100 rad/s
200 rad/s
300 rad/s
50 rad/s
150 rad/s
The angular velocity of the disc after 2.0 seconds if the disc starts from rest based on the torque rotation graph is 100 rad/s.
What is the graph about?A torque versus rotations graph is a visual representation of the relationship between the torque applied to an object and the resulting rotations produced by that torque.
Typically, the torque is plotted on the vertical axis, while the rotations are plotted on the horizontal axis. The resulting graph usually shows a linear relationship between torque and rotation, with the slope of the line indicating the object's rotational inertia or resistance to rotation.
The graph can be used to determine the amount of torque required to produce a certain amount of rotation in an object. Based on the graph, the correct option is A.
Learn more about torque on;
https://brainly.com/question/25615943
#SPJ1
2. How much current is in a resistor of 227 Ω if the potential difference across
the resistor is 145 V?
The 0.64 amp current flow is in a resistor of 227 Ω if the potential difference across the resistor is 145 V.
How do you determine current when there is resistance and a potential difference?The sum of the currents flowing through each branch represents the total current in the circuit. By dividing the total current for the circuit by the cell's potential difference, the total resistance for this circuit may be computed.
What is the potential difference current formula?Using the equation V = E d, determine the potential difference between the two locations. Subtract the current flow rate from the resistance that exists in the circuit. The process of multiplication results in the potential difference, which is measured in volts. This formula, V = I R, is known as Ohm's Law.
What conceivable variations exist in Ohm's law?The current times the resistance results in the potential difference, also known as voltage. One Joule of energy is produced when one Coulomb of charge moves between two points in a circuit with a potential difference of one Volt.
From ohm's law;
V = IR
Substitute values,
145 = I × 227
I = 0.64 Amp
To know more about the ohm's law visit;
https://brainly.com/question/796939
#SPJ1
Figure 1 shows history graphs of two different points on a string as a wave pulse moves along the string. The blue curve is the history graph for the point at x = 1.0 cm , and the green curve is for the point at x = -3.0 cm .
We know that Velocity = delta x /delta t = [-3 -1]cm/[5-0]s = - 0.8 cm/s answer
What is called velocity?Velocity is the direction at which an object is moving and serves as a measure of the rate at which its location is changing as seen from a specific point of view and as determined by a specific unit of time (for example, 60 km/h northbound). In kinematics, the area of classical mechanics that deals with the motion of things, velocity is a basic idea.
A physical vector variable called velocity must have both a value and a direction in order to be defined. Speed is the scalar absolute value (magnitude) of motion; it is a coherent derived unit whose amount is quantified in metres per second (m/s or m/s1) in the SI (metric system).
Learn more about velocity
https://brainly.com/question/17127206
#SPJ1
Which would have more matter: a 1 cm cube of lead or a 1 cm
cube of rubber?
Answer: 1CM CUBE OF LEAD
Explanation:
answer the following questions: which block has a higher temperature? iron does the hotter block have more energy inside? look closely! yes how would you explain that after putting in the same amount of heat, the two blocks have different temperatures? different
Yes, the hotter block has more energy inside. This is due to the fact that the materials of the two blocks have different heat capacities. Heat capacity is the amount of heat energy that must be added to a material to increase its temperature by 1°C. Generally speaking, materials with higher heat capacities will require more heat to raise their temperature by 1°C than materials with lower heat capacities.
For example, if two blocks, one made of iron and one made of aluminum, were both placed in a fire and given the same amount of heat energy, the block made of aluminum would be hotter than the block made of iron. This is because iron has a higher heat capacity than aluminum, meaning it takes more energy to heat it up. Therefore, the aluminum block has absorbed more heat energy and has a higher temperature than the iron block.
In conclusion, after receiving the same amount of heat energy, the two blocks have different temperatures because they have different heat capacities. The block with the higher heat capacity (iron) requires more energy to raise its temperature, resulting in a lower temperature than the block with the lower heat capacity (aluminum).
Know more about heat capacities here:
https://brainly.com/question/28302909
#SPJ11
The semiconductor cdse has a bandgap of 1. 74 ev. What wavelength of light would be emitted from an led made from cdse? what region of the electromagnetic spectrum is this?
The required wavelength is calculated to be 715 nm and it belongs to infrared region.
The band-gap of the semiconductor cdse is given as 1.74 ev.
The equation of Planck is mathematically written as,
E = h c /λ
where,
h is planck's constant
c is speed of light
λ is wavelength
E is energy/band-gap
Converting electron volts to joules we should multiply by 1.6 × 10⁻¹⁹ J
Putting all the known values and making wavelength as subject,
λ = h c /E = (6.626 × 10⁻³⁴× 3 ×10⁸)/(1.74× 1.6 × 10⁻¹⁹) = (19.88 × 10⁻²⁶)/(2.78× 10⁻¹⁹) = 7.15 × 10⁻⁷ m = 715 × 10⁻⁹ m = 715 nm
By looking into the wavelengths of electromagnetic spectrum, we can say that this wavelength belongs to infrared.
To know more about wavelength:
https://brainly.com/question/18403547
#SPJ4
A faulty model rocket moves in the xy-plane (the positive y-direction is vertically upward). The rocket's acceleration has components ax(t)=αt2
and ay(t)=β−γt
, where α
= 2. 50 m/s4
, β
= 9. 00 m/s2
, and γ
= 1. 40 m/s3. At t=0
the rocket is at the origin and has velocity v⃗ 0=v0xi^+v0yj^
with v0x
= 1. 00 m/s
and v0y
= 7. 00 m/s
a 1.60 m m tall person lifts a 1.40 kg k g book off the ground so it is 2.00 m m above the ground. part a what is the potential energy of the book relative to the ground?
27.44 J of the potential energy of the book relative to the ground, when a 1.60 m tall person lifts 1.40 kg of the book off the ground.
A 1.60 m m tall person lifts a 1.40 kg book off the ground so it is 2.00 m m above the ground.
The potential energy of the book relative to the ground would be:
PE = mgh
Where PE is the potential energy,
m is the mass,
g is the acceleration due to gravity, and
h is the height
The acceleration due to gravity is constant and is 9.8 m/s²
mass m = 1.40 kg
Height h = 2.00 m
mgh = 1.40 × 9.8 × 2.00 = 27.44 J
Ans: The potential energy of the book relative to the ground is 27.44 J.
Learn more about potential energy: https://brainly.com/question/14427111
#SPJ11
1. A 1.33-kg physics textbook is initially at rest on a steel table.
The textbook is then pushed with a constant force of 4.0 N.
Friction with a magnitude of 2.0 N is exerted on the moving
book by the surface of the table.
Determine the final velocity of the textbook after it has been
pushed 0.75 meter across the table.
The acceleration of the textbook is a = F/m = 2.0 N/1.33 kg = 1.5 m/s². and the final velocity of the textbook is v = 0 + (1.5 m/s²)(0.75 s) = 1.125 m/s.
What is acceleration?Acceleration is the rate at which an object changes its velocity over time. It is a vector quantity, meaning it has both magnitude and direction. An object's acceleration can be calculated by measuring the change in its velocity over time.
The net force acting on the textbook is the difference between the pushing force of 4.0 N and the frictional force of 2.0 N, which is 2.0 N.
According to Newton's Second Law, this net force of 2.0 N will cause an acceleration of the textbook given by the equation F = ma, where m is the mass of the textbook (1.33 kg) and a is the acceleration.
Therefore, the acceleration of the textbook is a = F/m = 2.0 N/1.33 kg = 1.5 m/s².
The final velocity of the textbook can then be calculated using the equation v = v0 + at, where v0 is the initial velocity (0 m/s, since the textbook was initially at rest), a is the acceleration (1.5 m/s²), and t is the time the textbook was pushed (0.75 m).
Therefore, the final velocity of the textbook is v = 0 + (1.5 m/s²)(0.75 s) = 1.125 m/s.
To learn more about acceleration
https://brainly.com/question/460763
#SPJ1
. Mention a few uses of magnets in our daily life.
Explanation:
Magnets are used to make a tight seal on the doors to refrigerators and freezers. They power speakers in stereos, earphones, and televisions. Magnets are used to store data in computers, and are important in scanning machines called MRIs (magnetic resonance imagers), which doctors use to look inside people's bodies
Someone please help!! thanks so much
For a particular cross-sectional area of the wire, 3.00 x [tex]10^{20}[/tex] electrons must go through it in 6.00 x [tex]10^{14}[/tex] seconds.
How can you figure out how long it takes an electron to travel across a wire with a specific cross-sectional area?Q = It, where I is the current, t is the time, and Q is the total charge.
Q = N
N is the quantity of electrons.
The two equations together give us:
Ne = It,
To solve for t, we obtain:
t = Ne/I
Inputting the values provided yields:
t = (3.00× [tex]10^{20}[/tex])
(1.60× [tex]10^{-19}[/tex] C/e) / (80.0× [tex]10^{-3}[/tex] A)
t = 6.00× [tex]10^{14}[/tex] s
For a particular cross-sectional area of the wire, 3.00 x [tex]10^{20}[/tex] electrons must go through it in 6.00 x [tex]10^{14}[/tex] seconds.
To learn more about current through a wire visit:
brainly.com/question/29832874
#SPJ1
Most people store much of their personal information digitally on a computer.
What happens to this information if it is accidentally deleted?
A. The information is backed up, but it is an inferior copy.
O
B. If the information is overwritten, it cannot be recovered.
C. The information is changed and becomes a computer virus.
O
D. The information is automatically backed up as analog storage.
SUBMIT
The correct option is A. If personal information is accidentally deleted from a computer, The information is backed up, but it is an inferior copy.
Information can be defined as a measure of the degree of uncertainty reduction obtained by receiving a message or measuring a system. It is a fundamental concept in many areas of physics, including thermodynamics, quantum mechanics, and information theory.
In thermodynamics, information is related to the entropy of a system, which quantifies the degree of disorder or randomness. The more information we have about a system, the lower its entropy and the more ordered it becomes.
In quantum mechanics, information is closely related to the concept of entanglement, where two or more particles become so strongly correlated that their states cannot be described independently. The amount of information that can be transmitted through an entangled system is limited by the laws of quantum mechanics.
To learn more about Information visit here:
brainly.com/question/13629038
#SPJ4
2. A person walks 20 m [N 20E], then
120 m [N 50W], then 150 m [W] and finally
30 m [S 75E]. Find the person final
displacement using trigonometric methods
The person's final displacement is approximately 227 meters at an angle of 17.9 degrees North of West.
The first displacement of 20 m [N 20° E] can be broken down as follows,
The x-component is 20 cos(20°) = 18.8 m to the East
The y-component is 20 sin(20°) = 6.8 m to the North
The second displacement of 120 m [N 50° W],
The x-component is 120 cos(50°) = -91.9 m to the West
The y-component is 120 sin(50°) = 92.2 m to the North
The third displacement of 150 m [W] has no y-component, and the x-component is simply -150 m to the West.
The fourth displacement of 30 m [S 75° E],
The x-component is 30 cos(75°) = 7.4 m to the East
The y-component is 30 sin(75°) = -28.6 m to the South
The total x-component is 18.8 m - 91.9 m - 150 m + 7.4 m = -215.7 m to the West. The total y-component is 6.8 m + 92.2 m + 0 m - 28.6 m = 70.4 m to the North
To find the magnitude of the resultant vector,
|d| = sqrt((-215.7 m)^2 + (70.4 m)^2) ≈ 227 m
To find the direction of the resultant vector,
θ = tan^-1(70.4 m / 215.7 m) ≈ 17.9° N of W
To know more about displacement, here
brainly.com/question/11058210
#SPJ4
Question 3
A 2,209 kg car travelling at 31 m/s hits the back of a 1,278 kg car that is travelling 5 m/s slower than the other car. The 2,209 kg
car goes 10 m/s slower than it was going before it hit. Both cars are travelling in the same direction. How fast will the car that got
hit from behind be going after the collision?
The car that got hit from behind will be going 48.05 m/s (or about 172.98 km/h) after the collision.
What is Collision?
In physics, a collision is an event where two or more objects come together and interact with each other, causing a transfer of energy and momentum between them. Collisions can be classified into two types: elastic and inelastic.
To solve this problem, we can use the conservation of momentum principle, which states that the total momentum of an isolated system remains constant before and after a collision. We can set up an equation for the conservation of momentum before and after the collision:
Before the collision:
(2209 kg)(31 m/s) + (1278 kg)(26 m/s) = total momentum
After the collision:
(2209 kg)(21 m/s) + (1278 kg)(vf) = total momentum
where vf is the final velocity of the 1,278 kg car after the collision.
Simplifying the equations, we get:
Before the collision: 76,079 kgm/s + 33,228 kgm/s = 109,307 kg*m/s
After the collision: 46,689 kgm/s + 1,278 kgvf = 47,967 kgm/s + 1,278 kgvf
Since the total momentum before and after the collision is the same, we can set the two equations equal to each other and solve for vf:
76,079 kgm/s + 33,228 kgm/s = 46,689 kgm/s + 1,278 kgvf
109,307 kgm/s = 47,967 kgm/s + 1,278 kg*vf
61,340 kgm/s = 1,278 kgvf
vf = 48.05 m/s
Therefore, the car that got hit from behind will be going 48.05 m/s (or about 172.98 km/h) after the collision.
Learn more about Collision from given link
https://brainly.com/question/24915434
#SPJ1
If a net force of 24 N is applied to an object with a mass of 6 kg, then what will the resulting
acceleration be according to Newton's second law of motion?
a
b
C
d
6 m/s²
0.25 m/s²
24 m/s²
4 m/s²
Answer:
d. 4m/s²
Explanation:
pls mrk me brainliest
a ball player wishes to determine pitching speed by throwing a ball horizontally from an elevation of 5 m above the ground. the player sees the ball land 20 m down range. what is the player's pitching speed?
The pitching speed of the player to cover a horizontal distance of 20 m when the ball is thrown horizontally from a height of 5 m is 19.82 m/s.
To find the pitching speed, we need to use the kinematic equation, which relates the distance traveled by an object to its initial velocity and the time it takes to travel that distance.
Since the ball is thrown horizontally, we can assume that the initial velocity of the ball is horizontal and the acceleration of the ball is vertical due to the force of gravity.
Using the equation of motion for the horizontal motion:
distance = speed × time
Since the ball is thrown horizontally, there is no initial vertical velocity, so the initial velocity is zero.
Therefore, distance = speed × time
time = distance/speed
Using the equation of motion for the vertical motion:
[tex]distance = initial \ velocity \times time + (1/2) \times acceleration \times time^2[/tex]
Since the ball is thrown horizontally, the initial vertical velocity is zero, and the acceleration due to gravity is 9.81 m/s² (since it is acting downward).
Therefore, [tex]distance = (1/2) \times (9.81) \times time^2[/tex]
[tex]time^2 = 2 \times distance/9.81[/tex]
[tex]time = \sqrt{2 \times distance / acceleration}[/tex]
Substituting the values
[tex]time = \sqrt{2\times(5/9.81)} = 1.009 s[/tex]
Now, substituting the value of time in the horizontal motion equation:
[tex]speed = distance/time[/tex]
[tex]speed = 20/1.009 = 19.82\ m/s[/tex]
Speed = 19.82 m/s
Therefore, the player's pitching speed is 19.82 m/s.
Learn more about velocity:
https://brainly.com/question/4931057
#SPJ11
A student is given a low voltage power supply and 1m of resistance wire. The student uses these and other pieces of equipment to measure the resistance of just 50cm of the resistance wire. Draw a diagram of the circuit that the students should use. Your circuit diagram should identify the pieces of equipment that the student uses
The student should use the power supply to provide a voltage source (V), the resistance wire (R) and an ammeter (A).The circuit diagram is V-A- R (50cm) -V.
What is resistance ?Resistance is the refusal to accept or comply with something. It is the opposition to a particular idea, policy, or course of action. Resistance can be seen in many forms, including physical, psychological, social, and political. Physically, it can be seen in the refusal to comply with a certain rule or law, or in the refusal to engage in a certain activity or behavior. Psychologically, it can be seen in the refusal to accept certain ideas, beliefs, or values. Socially, it can be seen in the refusal to engage in certain social practices or customs.
To learn more about resistance
https://brainly.com/question/17563681
#SPJ1
A stone hits the bottom of an old mineshaft that is 210 m deep. If the temperature in the mineshaft is 10°C, how many seconds pass before the sound is heard at the top of the mine shaft?
The speed of sound in air at 10°C is approximately 343 meters per second. Let's use the formula:
distance = speed x time
We want to find the time it takes for the sound to travel 210 meters to the top of the mineshaft. So we can rearrange the formula to solve for time:
time = distance ÷ speed
Plugging in the values we have, we get:
time = 210 ÷ 343
time ≈ 0.612 seconds
Therefore, it takes approximately 0.612 seconds for the sound to travel from the bottom to the top of the mineshaft.
When tension is applied to an aluminum rod (Y = 70 x 10^9 Pa) of length 1 m, it stretches by Δ.
1. If the same tension is applied to another aluminum rod with the same cross-sectional area, but of length 2 m, by how much will it stretch?
a) less than Δ
b) Δ
c) more than Δ
2. Now, consider two aluminum rods of length 1 m, one twice as thick as the other. If a compressive force F is applied to both rods, their lengths are reduced by Δthick rod
and Δthin rod, respectively.
The ratio (Δthick rod)/(Δthin rod) is
a) (Δthick rod)/(Δthin rod) < 1
b) (Δthick rod)/(Δthin rod) = 1
c) (Δthick rod)/(Δthin rod) > 1
The answers for the given questions about topic tension:
1. c.) More than ΔL
2. b.) <1
What is aluminium rod?Light and strong, an aluminium rod is highly resistant to corrosion and is ideal for both indoor as well as outdoor use as it can withstand a variety of environmental conditions. Our aluminium rods, which are also referred to as aluminium round bars, are provided in the 6000 series, which has the greatest commercial versatility.
The mechanical sectors can use aluminium alloy wire rods for things like bolts, nuts, nails, needles, rivets, clips, and staples.
1. stress = Y strain
(F / A) = Y (deltaL / L)
deltaL / L = constant (for this problem)
delta(L) / 1 = delta(L') / 2
delta(L') = 2 delta(L)
2. deltaL A = constant
L_thick (2A) = Lthin (A)
L_thick / L_thing = 1/2 < 1
To know more about tension, visit -
https://brainly.com/question/138724
#SPJ1
A pulley system is such that a person pulls down with 10 N of force to lift a 20 N object. The
machanical advantage is.
(MA = Fout/Fin)
O 0. 5
O 2
O
30
Please help me
Two is the mechanical benefit of the pulley mechanism.
The mechanical advantage of a pulley system is the ratio of the output force to the input force. In this case, the person is pulling down with a force of 10 N to lift a 20 N object. Therefore, the mechanical advantage can be calculated as follows:
MA = output force / input force
MA = 20 N / 10 N
MA = 2
The mechanical advantage of the pulley system is 2. This means that for every 1 unit of force the person applies, the object is lifted with 2 units of force. In other words, the pulley system allows the person to lift the object with less force than would be required without the pulley system.
To learn more about force refer to:
brainly.com/question/13191643
#SPJ4
Use the table below to answer this question.
Distance (mm) Electric Force (N)
1 243
3 27
5 10
7 5
9 3
A scientist measured the distance between two positively-charged objects, and determined the electric force between them. Based on the data in the table above, which of the following statements is true?
A
As the size of the objects increases, the size of the electric force between them decreases.
B
As the distance between the objects increases, the size of the electric force decreases.
C
The size of the electric force is constant.
D
As the distance between the objects increases, the objects become more positively charged.
As the distance between the objects increases, the size of the electric force decreases.
What is an electric ?Electricity is a form of energy that results from the movement of charged particles, such as electrons or ions. It is the flow of electric charge through a conductor, which can be used to power devices and machines. Electric phenomena occur naturally, such as in lightning strikes, but can also be harnessed and controlled for practical applications, including lighting, heating, and communication.
What is a distance ?Distance refers to the physical length between two points or objects, measured in units such as meters, kilometers, miles, or inches. It is a scalar quantity that only has magnitude and no direction. Distance can be measured using various tools and methods, such as rulers, odometers, or GPS devices.
To know more about electric visit :
https://brainly.com/question/8971780
#SPJ!
A coconut is free-falling vertically from a tree. The gravitational potential energy of the coconut when it starts to fall is 560J
a) Calculate the mechanical energy of the coconut when it begins to fall.
b) Find the kinetic energy of the coconut when it hits the ground.
c) Calculate the kinetic energy, potential energy & mechanical energy of the coconut at a position 1/2 the height when it started to fall.
Question
A coconut of mass m falls from its tree through a vertical distance of s and could reach ground with a velocity of v ms−1 due to air resistance. The work done by air resistance is:
A.) −m/2 (2gs−v2)
B.) −1/2 mv^2
C.) −mgs
D.) mv^2+2mgs
Solution
Correct option is A)
Here, a coconut of mass m falls from its tree through a vertical distance of s, with a velocity of v hence work done by gravity is,
Wg=mgs .......(1)
Change in velocity of coconut is,
E=1/2m(u−v)^2 = −1/2m(v)2 ........(2)
Now, total work done on coconut is equal to change in kinetic energy hence,
Wa+Wg=1/2mv^2
where, Wa is work done by air resistance.
Using (1) and (2), we get
Wa=1/2mv^2−Wg
Wa=1/2mv^2−mgs
Wa=−m/2(2gs−v2)
this might not be the question but it is for you to be better
mark me as brainliest
observe where your house is located and from this explain why your house is hot or cold
The temperature inside a house can be influenced by various factors such as the geographic location, orientation of the house, insulation, and the type of construction materials used.
For instance, if a house is located in a hot and humid climate, it may become hot inside due to the external heat and humidity, even with air conditioning.
On the other hand, a house located in a cold climate may become cold inside, especially during the winter season, due to heat loss from the interior to the cold outside environment.
Proper insulation and efficient heating/cooling systems can help regulate the temperature inside a house and improve its energy efficiency.
For such more question on temperature:
https://brainly.com/question/27944554
#SPJ11