pH = 10.88
what is the OH-

The code for corrosion control of underground storage tank systems by cathodic protection is  B) SP0169

Petroleum products are kept in a tank farm before being distributed to end users or retail establishments. A tank farm often has extremely basic amenities. Tanks can be above or below ground, with plumbing to link them to tankers and pipelines to allow fuel to be dispensed and the tanks to be filled. Numerous tank farms are situated close to ports, rail yards, major trucking terminals, and refineries (for convenience). Moving fuel into and out of the farm is made simple by these places. Another possible location for a tank farm is alongside a pipeline that carries petroleum products. In tank farms, cathodic protection systems and grounding systems may be used for corrosion control and safety reasons, respectively.
The correct code for Corrosion Control of Underground Storage Tank Systems by Cathodic Protection is:

B) SP0169

LEARN MORE ABOUT Cathodic Protection

https://brainly.com/question/31557529

#SPJ11

The skier's speed, height, and time, are not directly related to the determination of the reaction force of the snow pushing on the skier.

Chemical reactions are fundamental processes in which atoms are rearranged to form new substances with different properties than the original ones. A chemical reaction occurs when reactants come together in a specific way to form products. Reactants are the starting materials, while products are the new substances formed by the reaction.

Chemical reactions are governed by the laws of thermodynamics and kinetics. The law of conservation of mass dictates that the total mass of the reactants must be equal to the total mass of the products. The law of conservation of energy states that energy cannot be created or destroyed, only transformed from one form to another. Therefore, chemical reactions must either absorb or release energy, depending on the nature of the reaction. Chemical reactions can be classified as exothermic or endothermic. Exothermic reactions release energy, usually in the form of heat, while endothermic reactions absorb energy.

To learn more about Reaction visit here:

brainly.com/question/17434463

#SPJ4

The pressure (in mmHg) of the 9.62 L container having 4.95 moles of gas at 592.84 is 19022.77 mmHg

First, we shall list out the given parameters from the question. This is shown below:

Ideal gas equation states as follow:

PV = nRT

Inputting the give parameters, we can obtain the pressure as follow:

P × 9.62 = 4.95 × 62.36 × 592.84

P × 9.62 = 182999.03688

Divide both sides by 9.62

P = 182999.03688 / 9.62

P = 19022.77 mmHg

Thus, we can conclude from the above calculation that the pressure of the container is 19022.77 mmHg

Learn more about pressure:

https://brainly.com/question/15343985

#SPJ1

The following formula can be used to determine how many moles of KC1 are present in 1250 mL of 0.75 M KC1: Molarity (M) is equal to the moles of solute per litre of solution.

In this instance, the volume of the solution is 1250 mL, and the molarity of KC1 is 0.75 M. The following formula can be used to determine how many moles of KC1 are present in 1250 mL of 0.75 M KC1: Molarity (M) times the number of litres in the solution equals 0.75 M times (1250 mL/1000 mL/L) or 0.9375 moles of KC1.

Consequently, 0.9375 moles of KC1 are present in 1250 mL of 0.75 M KC1. It is significant to remember that a solution's molarity is a measurement of the amount of a solute present in a given volume of the solution.

Learn more about molarity   at:

https://brainly.com/question/8732513

#SPJ1

The chemical associated with homeostatic sleep drive is adenosine. Adenosine is a naturally occurring chemical compound in the body that is a byproduct of the breakdown of ATP (adenosine triphosphate), the primary energy source for cells. Adenosine levels increase in the brain as wakefulness persists, and its buildup eventually signals to the brain that it is time to sleep.

Adenosine acts as an inhibitor of wake-promoting neurons in the brain, leading to drowsiness and a desire to sleep. Caffeine, which is a widely used stimulant, works by blocking the effects of adenosine in the brain, thereby promoting wakefulness. The homeostatic sleep drive, which is the body's natural tendency to regulate sleep-wake cycles, is closely linked to adenosine levels. The accumulation of adenosine during wakefulness drives the need for sleep, and the reduction of adenosine during sleep prepares the body for wakefulness. In summary, adenosine plays a critical role in the regulation of sleep-wake cycles, and its levels in the brain are closely linked to the homeostatic sleep drive.

Learn More about ATP here :-

https://brainly.com/question/859444

#SPJ11

The orbital diagram of the P^3- anion is shown in the orbital diagram attached.

An orbital diagram is a visual representation of where electrons are located within an atom or ion. A series of boxes or circles is used to symbolize an atomic orbital, which is the region of space around the nucleus where electrons are most likely to be found.

Each box or circle, which stands for an atomic orbital, has an image of an electron inside it, represented by an arrow.

Orbital diagrams can be used to visualize and understand the electronic structure of atoms and ions, as well as to predict their chemical and physical properties.

Learn more about orbital diagram:https://brainly.com/question/28809808

#SPJ1

The solution formed by each salt can be acidic, basic, or neutral depending on the behavior of the salt in water. In this case, the base [tex]NH_3[/tex] is stronger than the acid HF, and thus, the solution formed by the salt [tex]K(NH_3)[/tex] will be basic. The solution formed by the salt HF will be acidic.

[tex]K(NH_3)[/tex] : This salt is formed by the reaction between KOH (a strong base) and  [tex]NH_3[/tex] (a weak base). Since KOH is a strong base, it will completely dissociate into K and  [tex]OH^{-}[/tex] ions in water.  [tex]NH_3[/tex] , on the other hand, is a weak base and will partially dissociate into [tex]NH_4^{+}[/tex] and [tex]OH^{-}[/tex] ions. The resulting solution will be basic due to the excess of   [tex]OH^{-}[/tex] ions present.

HF: This salt is formed by the reaction between NaOH (a strong base) and HF (a weak acid). NaOH will completely dissociate into [tex]OH^{-}[/tex] ions in water. HF, being a weak acid, will partially dissociate into H and F ions. The resulting solution will be acidic due to the excess of H ions present.

To determine whether the resulting solution is acidic or basic, we need to compare the strengths of the acid and the base formed by the salt hydrolysis. If the acid is stronger than the base, the resulting solution will be acidic. If the base is stronger than the acid, the resulting solution will be basic. If the acid and base are of equal strength, the resulting solution will be neutral.

Learn more about neutral solution visit: brainly.com/question/29510389

#SPJ4

The theoretical yield of compound is 2.0 g, and the actual amount of compound isolated at the end of the reaction is 1.32 g.

Based on the information given, the theoretical yield of compound would be calculated as follows:

1. Determine the limiting reactant by calculating the moles of each compound:
Moles of compound = initial amount of compound / molecular weight of compound
Moles of compound = 2.0 g / (molecular weight of compound)
Moles of compound = x g / (molecular weight of compound)

The limiting reactant is the one that produces the smallest amount of product. In this case, we will assume that compound is the limiting reactant.

2. Calculate the theoretical yield of compound:
Theoretical yield of compound = (moles of limiting reactant) x (molecular weight of compound)
Theoretical yield of compound = (moles of compound) x (molecular weight of compound)
Theoretical yield of compound = (2.0 g / molecular weight of compound) x (molecular weight of compound)
Theoretical yield of compound = 2.0 g
The theoretical yield of compound is 2.0 g.

Next, we need to calculate the actual amount of compound that was isolated at the end of the reaction:
Actual yield of compound = percent yield x theoretical yield
Actual yield of compound = 0.66 x 2.0 g
Actual yield of compound = 1.32 g

To know more about the theoretical yield refer here :

https://brainly.com/question/30700754#

#SPJ11

If the solubility of Zn(OH)₂ at 25°C is 4.2 × 10⁻⁴ g/L, then the K_sp for Zn(OH)₂ is 3.01 × 10⁻¹⁶.

The solubility of Zn(OH)₂ at 25°C is 4.2 × 10⁻⁴ g/L. To calculate K_sp, we need to first determine the molar concentration of Zn(OH)₂ in water. The molar mass of Zn(OH)₂ is approximately 99.4 g/mol (Zn: 65.4 g/mol, O: 16 g/mol, H: 1 g/mol).

Next, convert the solubility to molar concentration:

(4.2 × 10⁻⁴ g/L) / (99.4 g/mol) ≈ 4.23 × 10⁻⁶ mol/L

When Zn(OH)₂ dissolves in water, it ionizes into its constituent ions:

Zn(OH)₂ (s) ⇌ Zn²⁺ (aq) + 2OH⁻ (aq)

According to the stoichiometry, one mole of Zn(OH)₂ produces one mole of Zn²⁺ ions and two moles of OH⁻ ions. Therefore, the molar concentrations of Zn²⁺ and OH⁻ ions are as follows:

[Zn²⁺] = 4.23 × 10⁻⁶ mol/L

[OH⁻] = 2 × 4.23 × 10⁻⁶ mol/L = 8.46 × 10⁻⁶ mol/L

Now, we can calculate the K_sp using these concentrations:

K_sp = [Zn²⁺][OH⁻]²

K_sp = (4.23 × 10⁻⁶)(8.46 × 10⁻⁶)² ≈ 3.01 × 10⁻¹⁶

Rounded to two significant digits, the K_sp for Zn(OH)₂ at 25°C is 3.0 × 10⁻¹⁶.

To know more about stoichiometry, refer to the link below:

https://brainly.com/question/28780091#

#SPJ11

The correct answer is E) lock out and tag out of break or AC disconnect. Before installing an interrupter in a rectifier, it is necessary to ensure that the system is de-energized and cannot be accidentally turned on.

This can be done through the lockout and tagout procedure, which involves locking the system and placing a tag on it to indicate that it should not be operated. This helps to prevent accidents and ensures the safety of the personnel working on the system.Lockout and tagout is a critical safety procedure that should be followed whenever work is being done on electrical equipment. It helps to prevent accidents and ensures that personnel are not exposed to electrical hazards. Before installing an interrupter in a rectifier, it is important to follow this procedure to ensure that the system is de-energized and safe to work on.

Learn more about  interrupter here:

https://brainly.com/question/29770273

#SPJ11

Based on the DNA sequences provided, Person A and Person C are more closely related.

To determine relation, compare the nucleotides at each position in the sequences.

At position 1, Person A and Person C both have "A" nucleotide, while Person B has "G" nucleotide.

At position 2, Person A has "T" nucleotide, Person B has "T" nucleotide, and Person C has "C" nucleotide.

At position 3, Person A and Person C both have "C" nucleotide, while Person B has "T" nucleotide.

Continuing this method for all places in the sequences reveals that Person A and Person C share more nucleotides than Person B. This shows that they are linked to each other more closely than to Person B.

In terms of concrete evidence for evolution, new dog breeds, drought-resistant crops, and more virulent viruses are all instances of microevolution at work.

Find out more on evolution here: https://brainly.com/question/27748371

#SPJ1

No, the mass of a neutral atom of 18O is not equal to the sum of the masses of 8 atoms of 1H and 10 neutrons.

The mass of an atom is not only determined by the number of protons and neutrons it has, but also by the energy that holds these particles together. This energy is called the binding energy, and it can vary depending on the arrangement of the particles in the nucleus.

In the case of 18O, the binding energy between the protons and neutrons is different than the binding energy between hydrogen atoms and neutrons. Therefore, the mass of a neutral atom of 18O cannot be calculated simply by adding up the masses of its constituent particles.

Additionally, it is important to note that the mass of a neutral atom of 18O is not exactly 18 atomic mass units (amu) either. This is because the mass of an atom is also affected by the electrons in its outer shells. The exact mass of an atom of 18O is 17.999 amu.

learn more about neutral atom

https://brainly.com/question/24652228

#SPJ11

The diene that reacts with one equivalent of HBr to form the two bromoalkene products described in the question can be drawn as follows:

    H          H

    |          |

H3C-C=C-CH2-CH=CH2

    |          |

    H          H

In this diene, there are two double bonds, one between carbons 2 and 3 and another between carbons 4 and 5. When one equivalent of HBr is added to this diene, an electrophilic addition reaction occurs in which the H and Br add to the two double bonds to form two different products, as described in the question.

The effect of increasing temperature on the relative amount of each product can be explained by considering the mechanism of the reaction. The reaction proceeds through a carbocation intermediate, which is formed by protonation of the diene with HBr. The carbocation intermediate can then react with Br- to form the bromoalkene products.

Product 1 is formed by the addition of HBr to the double bond between carbons 2 and 3, which results in the formation of a more stable tertiary carbocation intermediate. As the temperature increases, the reaction rate increases, which can lead to a higher proportion of product 1 being formed. However, at very high temperatures, the reaction rate can become too fast, leading to increased side reactions such as rearrangements, which can decrease the relative amount of product 1.

Product 2 is formed by the addition of HBr to the double bond between carbons 4 and 5, which results in the formation of a less stable secondary carbocation intermediate. As the temperature increases, the reaction rate also increases, which can lead to a higher proportion of product 2 being formed. However, at very high temperatures, the reaction rate can become too fast, leading to increased side reactions such as elimination, which can decrease the relative amount of product 2.  Therefore, the answer to the question is that as the temperature increases, the relative amount of product 1 is expected to increase, while the relative amount of product 2 is expected to decrease due to side reactions. However, at very high temperatures, both products can be affected by side reactions, and the relative amounts may not change significantly.

for more such questions on HBr

https://brainly.com/question/30515842

#SPJ11

Answer: Sure thing! The solubility product constant (Ksp) for BaSO4 at 298 K is 1.1 x 10^-10. To calculate the solubility (S) of BaSO4 in mol/L at 298 K, we can use the following expression:

Ksp = [Ba2+][SO42-]

where [Ba2+] is the molar concentration of Ba2+ ions and [SO42-] is the molar concentration of SO42- ions in solution. Since BaSO4 is a sparingly soluble salt, we can assume that the concentration of Ba2+ and SO42- ions in solution is equal to the solubility of BaSO4 (S). Therefore:

Ksp = S^2

S = sqrt(Ksp)

S = sqrt(1.1 x 10^-10) = 1.05 x 10^-5 mol/L

Therefore, the solubility of BaSO4 in mol/L at 298 K is 1.05 x 10^-5 mol/L.

Explanation:

Alkalinity is a measure of the water's ability to neutralize acids. It is usually expressed as mg/l as CaCO3. In order to determine the alkalinity of a water sample at pH 6.8 containing 10 mg/l CO32- and 75 mg/l of HCO3-, we need to first understand the relationship between these parameters and alkalinity.

CO32- and HCO3- are both considered alkaline substances, meaning they can neutralize acids. However, they do so in different ways. CO32- reacts with acids to form HCO3-, which can then further react with acids to form CO2 and H2O. On the other hand, HCO3- can react directly with acids to form CO2 and H2O. To calculate the alkalinity of the water sample, we need to consider both of these reactions. First, we need to determine how much HCO3- is present in the sample. Since HCO3- is an acidic form of CO32-, we can assume that all of the CO32- will react with H+ ions to form HCO3-. Therefore, the total alkalinity due to CO32- is equal to the amount of CO32- present in the sample, or 10 mg/l. Next, we need to determine how much alkalinity is contributed by HCO3-. Since HCO3- can react directly with acids to form CO2 and H2O, we need to calculate how much HCO3- would be required to neutralize all of the H+ ions present in the sample. To do this, we need to convert the pH of the sample to a hydrogen ion concentration ([H+]). At pH 6.8, [H+] is approximately 1.6 x 10^-7 mol/l. Therefore, the total amount of HCO3- required to neutralize all of the H+ ions present in the sample is: (1.6 x 10^-7 mol/l) x (75 mg/l / 61.0168 g/mol) x (1000 mg/g) = 0.197 mg/l as CaCO3 Therefore, the total alkalinity of the water sample is: 10 mg/l + 0.197 mg/l = 10.197 mg/l as CaCO3.

Learn more about hydrogen ion here-

https://brainly.com/question/20309096

#SPJ11

It would take approximately 27,317 seconds or 7.59 hours to deposit 0.196 grams of cadmium metal from the solution.

We can use Faraday's laws of electrolysis to calculate the time required to deposit 0.196 grams of cadmium metal from a solution that contains cadmium ions using an electric current of 0.769 A.

According to Faraday's laws, the mass of a substance (in grams) that is deposited at an electrode is directly proportional to the quantity of electricity (in coulombs) that flows through the electrode. The constant of proportionality is known as the electrochemical equivalent (E) and its value depends on the substance being deposited.

The electrochemical equivalent of cadmium is 0.00000933 g/C. Therefore, the quantity of electricity required to deposit 0.196 grams of cadmium is:

quantity of electricity = mass / E = 0.196 g / 0.00000933 g/C = 21,015 C

We can use this value and the electric current to calculate the time required to deposit the cadmium using the formula:

time = quantity of electricity / current

Substituting the given values, we get:

time = 21,015 C / 0.769 A = 27,317 s

Therefore, by calculating it is said that it would take approximately 27,317 seconds or 7.59 hours.

To know more about the cadmium refer here :

https://brainly.com/question/10833977#

#SPJ11

How many seconds are required to deposit 0.196 grams of cadmium metal from a solution that contains ions, if a current of 0.769 a is applied.

The process that is expected to have an increase in entropy is the decomposition of N₂O₄ gas to NO₂ gas (Option B).

The decomposition of a gas into two different gases results in an increase in the number of particles and therefore an increase in disorder or entropy. The formation of liquid water from hydrogen and oxygen gas and the precipitation of BaSO₄ from mixing solutions of BaCl₂ and Na₂SO₄ are both examples of processes that result in a decrease in entropy as the particles become more ordered. Iron rusting can also be considered an increase in entropy as the solid metal turns into a mixture of solid and liquid particles.

Learn more about entropy: https://brainly.com/question/24278877

#SPJ11

The molarity of the sodium hydroxide solution is 0.253 M. This means that there are 0.253 moles of NaOH in 1 liter of the solution.

To determine the molarity of the sodium hydroxide solution, we can use the equation:

Molarity of NaOH = (Molarity of HCl) x (Volume of HCl) / (Volume of NaOH)

First, we need to calculate the number of moles of HCl used in the titration. We can do this using the formula:

Number of moles of HCl = Molarity x Volume

Substituting the given values, we get:

Number of moles of HCl = 0.1985 M x 0.03896 L = 0.00774356 moles

Now, let's calculate the volume of NaOH used in the titration by subtracting the initial buret reading from the final buret reading:

Volume of NaOH = 31.93 ml - 1.24 ml = 30.69 ml = 0.03069 L

Substituting these values in the equation, we get:

Molarity of NaOH = (0.1985 M) x (0.03896 L) / (0.03069 L) = 0.253 M

Therefore, the molarity of the sodium hydroxide solution is 0.253 M. This means that there are 0.253 moles of NaOH in 1 liter of the solution.

It is important to note that standardizing a solution is a crucial step in ensuring accurate and precise results in chemical analysis. By standardizing the NaOH solution, we can determine its exact concentration and use it for future titrations with confidence.

for more such questions on   hydroxide

https://brainly.com/question/21393201

#SPJ11

The pH value in the titration after the addition of 60.0 ml of 0.200 m HNO₃ is 1.74. At the end point, all the base has reacted with the acid and the solution is neutral.

To solve this problem, we need to use the concept of titration and the equation for the reaction between sodium hydroxide (NaOH) and nitric acid (HNO₃):
NaOH + HNO₃ → NaNO₃ + H₂O
In this reaction, NaOH is a base and HNO₃ is an acid. During titration, we add the acid slowly to the base until the reaction is complete.
We can use the equation:
moles of NaOH = moles of HNO₃
to calculate the amount of HNO₃ required to react with the NaOH in the sample. We can then use the remaining amount of HNO₃ added to the solution after the end point to calculate the pH.
First, let's calculate the number of moles of NaOH in the sample:
moles of NaOH = concentration x volume
moles of NaOH = 0.200 M x 0.0500 L
moles of NaOH = 0.0100 mol
Since the molar ratio of NaOH to HNO₃ is 1:1, we know that we need 0.0100 mol of HNO₃ to react completely with the NaOH. Let's see how much HNO₃ we added to the solution after 60.0 ml:
moles of HNO₃ = concentration x volume
moles of HNO₃ = 0.200 M x 0.0600 L
moles of HNO₃ = 0.0120 mol
Since we only needed 0.0100 mol of HNO₃ to react with the NaOH, we have 0.0020 mol of HNO₃ left in the solution. To calculate the pH, we need to find the concentration of H⁺ ions in the solution. This can be done using the equation:
[H⁺] = moles of HNO₃ left / total volume of solution
Total volume of solution = volume of NaOH + volume of HNO₃ added
Total volume of solution = 0.0500 L + 0.0600 L
Total volume of solution = 0.1100 L
[H⁺] = 0.0020 mol / 0.1100 L
[H⁺] = 0.0182 M
To find the pH, we can use the equation:
pH = -log[H⁺]
pH = -log(0.0182)
pH = 1.74
Therefore, the pH Value in the titration after the addition of 60.0 ml of 0.200 M HNO3 is 1.74.

Learn more about pH value here

https://brainly.com/question/26559093

#SPJ11

The combined weight of 1 mol of H atoms and 1 mol of Li atoms is 7.94 grams.

To calculate the combined weight of 1 mol of H atoms and 1 mol of Li atoms, you need to use the molar masses of both elements.
Step 1: Find the molar masses of H and Li
The molar mass of hydrogen (H) is approximately 1 gram/mol, and the molar mass of lithium (Li) is approximately 6.94 grams/mol.
Step 2: Calculate the combined weight
To find the combined weight, you simply add the molar masses of the two elements:
Combined weight = (1 mol of H atoms * molar mass of H) + (1 mol of Li atoms * molar mass of Li)
Combined weight = (1 * 1 g/mol) + (1 * 6.94 g/mol)
Combined weight = 1 g + 6.94 g
Combined weight = 7.94 g
So, the combined weight of 1 mol of H atoms and 1 mol of Li atoms is 7.94 grams.

learn more about molar mass Refer: https://brainly.com/question/21867422

#SPJ11

The negative sign indicates that the concentration gradient is in the direction of high to low hydrogen concentration. The flux of hydrogen through the foil is 4.3 × [tex]10^5[/tex] atoms/([tex]cm^2.s[/tex]) from the high hydrogen gas to the low hydrogen gas.

J = -D (dC/dx)

a) The concentration gradient of hydrogen can be calculated as follows:

dC/dx = (C2 - C1)/x

dC/dx = (2 × 10³ - 5 × [tex]10^8[/tex])/(0.001 × 2.54 × [tex]10^{-4}[/tex]) = -7.8 × [tex]10^{14}[/tex] atoms/[tex]cm^4[/tex]

(b) The flux of hydrogen through the foil can be calculated using Fick's first law:

J = -D (dC/dx)

D = D0 exp(-Q/RT)

D = 1.6 ×[tex]10^{-6}[/tex]exp(-44,200/8.31/923) = 5.5 × 10^-10 [tex]cm^2/s[/tex]

Substituting the calculated concentration gradient, we get:

J = -D (dC/dx) = -5.5 × [tex]10^{-10}[/tex] × (-7.8 × [tex]10^{14}[/tex]) = 4.3 × [tex]10^5[/tex] atoms/([tex]cm^2.s[/tex])

Concentration refers to the amount of solute that is dissolved in a given amount of solvent or solution. It is an essential concept in chemistry and plays a vital role in many processes such as synthesis, reaction, and separation. The concentration of a solution can affect its properties and behavior. For example, a more concentrated solution may have a higher boiling point or freezing point than a less concentrated one.

There are several ways to express the concentration of a solution, including molarity, molality, mass percent, mole fraction, and parts per million (ppm). Molarity is the most commonly used unit and is defined as the number of moles of solute dissolved per liter of solution. Molality is another unit that measures the number of moles of solute per kilogram of solvent.

To learn more about Concentration  visit here: brainly.com/question/10725862

#SPJ4

When a strong acid is titrated with a weak base, the pH of the solution at the equivalence point is less than 7.

For more such question on pH

https://brainly.com/question/12609985

#SPJ11

The chemist should pour out 10 mL of the silver(ii) oxide stock solution into a graduated cylinder and dilute it with distilled water to prepare a 100 mL aqueous silver(ii) oxide working solution with a concentration of 0.01 M.

To calculate the volume of the silver(ii) oxide stock solution that the chemist should pour out, we need to use the dilution equation:
C1V1 = C2V2
where C1 is the concentration of the stock solution, V1 is the volume of the stock solution to be poured out, C2 is the desired concentration of the working solution, and V2 is the final volume of the working solution.
Let's assume that the concentration of the silver(ii) oxide stock solution is 0.1 M and the desired concentration of the working solution is 0.01 M. We also need to know the final volume of the working solution, which is not given in the question. Let's assume that the chemist wants to prepare 100 mL of the working solution.
Substituting the values in the dilution equation, we get:
0.1 M x V1 = 0.01 M x 100 mL
Solving for V1, we get:
V1 = (0.01 M x 100 mL) / 0.1 M
V1 = 10 mL
Therefore, the chemist should pour out 10 mL of the silver(ii) oxide stock solution into a graduated cylinder and dilute it with distilled water to prepare a 100 mL aqueous silver(ii) oxide working solution with a concentration of 0.01 M. This calculation assumes that the chemist has a silver(ii) oxide stock solution with a known concentration and that she wants to prepare a working solution with a lower concentration.

for more such question on  stock solution

https://brainly.com/question/24697661

#SPJ11

A water molecule has a tetrahedral shape, with the central oxygen atom and two hydrogen atoms at three of the four apexes, and partial negative charges at the remaining two apexes. This shape is due to the arrangement of electrons in the molecule.

The oxygen atom in water has six valence electrons, which form four covalent bonds with the two hydrogen atoms and two lone pairs.

These lone pairs cause a slight distortion in the shape of the molecule, resulting in a tetrahedral arrangement.

Hence, the tetrahedral shape of a water molecule is due to the arrangement of electrons and results in partial negative charges at two of the apexes, with the central oxygen atom and two hydrogen atoms at the other three.

learn more about molecule click here:

https://brainly.com/question/475709

#SPJ11

One UV photon can break the atomic bond of almost one water molecule. However, it is important to note that the actual number of molecules/atoms that can be changed by one photon depends on several factors, such as the intensity and duration of the exposure.

For more such question on photon

https://brainly.com/question/27856390

#SPJ11

The typical sampling time for an active tube procedure can vary depending on the specific application and the sampling requirements.

However, it is typically shorter than 4 hours and can range from a few minutes to a few hundred minutes (i.e. 4 minutes to 200 minutes), A typical sampling time for an active tube procedure is 200 minutes.

In this procedure, an air sample is drawn through an active tube at a specific flow rate for a certain period, known as the "sampling time." The tube collects and concentrates the target compounds present in the air, which can then be analyzed to determine their concentrations.

To know more about sampling requirements:- https://brainly.com/question/18630925

#SPJ11

The molecular formula C6H14 represents a saturated hydrocarbon with six carbon atoms and 14 hydrogen atoms. To determine the number of structural isomers, we need to consider the different ways in which these atoms can be arranged in a molecule while maintaining the same molecular formula.

One way to approach this problem is to start with the straight-chain structure of n-hexane, which has all six carbon atoms in a row with each carbon atom bonded to two hydrogen atoms. This isomer is called the n-isomer or normal hexane. The other isomers can be obtained by branching or rearranging the carbon chain.The first branched isomer is 2-methylpentane, which has a five-carbon chain with a methyl (CH3) group attached to the second carbon atom. The second branched isomer is 3-methylpentane, which has a five-carbon chain with a methyl group attached to the third carbon atom. The third branched isomer is 2,2-dimethylbutane, which has a four-carbon chain with two methyl groups attached to the second carbon atom.The fourth isomer is 2,3-dimethylbutane, which has a four-carbon chain with one methyl group attached to the second carbon atom and another methyl group attached to the third carbon atom. The fifth isomer is 2,4-dimethylpentane, which has a five-carbon chain with one methyl group attached to the second carbon atom and another methyl group attached to the fourth carbon atom.Therefore, the answer is B. 5, there are five structural isomers possible with the molecular formula C6H14.

Learn more about hydrocarbon here

https://brainly.com/question/29318707

#SPJ11