The voltage is calculated using Ohm's Law, which states that voltage (V) equals current (I) multiplied by resistance (R). Therefore, V = I x R. Plugging in the given values, we get V = 0.1A x 1Ω = 0.1V. Therefore, the answer is A) 0.1V.
In this scenario, the resistance is 1 Ohm, and the current is 100 milliamps (mA). By multiplying these values, we can determine the voltage across the circuit. This is an example of using Ohm's Law to calculate the voltage in a circuit based on the resistance and current.
Given that the resistance is 1 Ohm and the current is 100 mA, the voltage is:
To find the voltage, we will use Ohm's Law: V = I × R
Where V is the voltage, I is the current, and R is the resistance.
Step 1: Convert current to Amps: 100 mA = 0.1 A (since 1 A = 1000 mA)
Step 2: Multiply current (in Amps) by resistance: V = 0.1 A × 1 Ohm
Step 3: Calculate voltage: V = 0.1 V
So, the correct answer is:
A) 0.1V
To know more about resistance visit :-
https://brainly.com/question/17563681
#SPJ11
apply 500 newtons of force until the speed reaches approximately 20 m/s. then, remove the force. describe the motion of the box
Answer:
it is at rest or you can say it is equilibriant
The box will undergo an initial period of acceleration until it reaches a speed of 20 m/s, at which point it will continue to move at a constant velocity in the absence of any external forces.
Assuming that the box is initially at rest and that there is no friction, when a force of 500 newtons is applied, the box will accelerate in the direction of the applied force. The acceleration of the box can be calculated using Newton's second law of motion:
F = m a
where F is the net force acting on the box, m is the mass of the box, and a is the acceleration of the box.
In this case, F = 500 N and m is the mass of the box, which we will assume to be 10 kg for the sake of example. Therefore, the acceleration of the box is:
[tex]a = F / m = 500 N / 10 kg = 50 m/s^2[/tex]
As the force is applied, the box will continue to accelerate until it reaches a speed of approximately 20 m/s. Once the box reaches this speed, the force is removed. Since there is no friction, the box will continue to move at a constant velocity of 20 m/s due to the principle of inertia.
In summary, the box will undergo an initial period of acceleration until it reaches a speed of 20 m/s, at which point it will continue to move at a constant velocity in the absence of any external forces.
To know more about acceleration, visit:
https://brainly.com/question/30660316#
#SPJ11
consider a rod of length l rotated about one of its ends instead of about its center of mass. if the mass of the rod is 5 kg, and the length is 2 meters, calculate the magnitude of the moment of inertia (i). a. 1.67 kgm^2 b. 0.833 kgm^2 c. 6.67 kgm^2 d. 3.33 kgm^2
To calculate the moment of inertia of a rod of length l rotated about one of its ends, we need to use the formula I = (1/3) * m * l^2. Here, m is the mass of the rod and l is its length.
Plugging in the values given in the question, we get:
I = (1/3) * 5 kg * (2m)^2
I = (1/3) * 5 kg * 4 m^2
I = (5/3) * 4 kgm^2
I = 6.67 kgm^2
Therefore, the correct answer is option c) 6.67 kgm^2.
It is important to note that the moment of inertia depends not only on the mass of the object but also on how the mass is distributed around the axis of rotation. In this case, since the rod is being rotated about one of its ends, the mass is not uniformly distributed and the moment of inertia is higher than if it were being rotated about its center of mass. This concept is crucial in understanding rotational motion and its applications in engineering and physics.
Learn more about inertia here:
https://brainly.com/question/3268780
#SPJ11
An observatory records gamma rays and radio waves from the same galaxy. Which of the following claims best indicates the signal with a longer wavelength and predicts the length of time it takes for each type of signal to get to Earth? (A) Longer Wavelength Radio waves Time Taken to Get to Earth Gamma rays take longer. (c) D Longer Wavelength Radio waves Longer Wavelength Gamma rays Longer Wavelength Gamma rays Time Taken to Get to Earth The waves take the same amount of time. Time Taken to Get to Earth Radio waves take longer. Time Taken to Get to Earth The waves take the same amount of time.
An observatory records gamma rays and radio waves from the same galaxy. The best claim that indicates the signal with a longer wavelength and predicts the length of time it takes for each type of signal to get to Earth is:
Longer Wavelength: Radio waves
Time Taken to Get to Earth: The waves take the same amount of time.
Radio waves have longer wavelengths than gamma rays, as they fall at opposite ends of the electromagnetic spectrum. However, both signals travel at the speed of light, which means they will take the same amount of time to reach Earth from the galaxy. Since they are emitted from the same source, the time taken for both types of waves to arrive at the observatory will be equal.
learn more about gamma rays here
https://brainly.com/question/23281551
#SPJ11
Calculate ΔGΔ� for the reaction NO(g)+O3(g)→NO2(g)+O2(g)��(�)+�3(�)→��2(�)+�2(�) for these conditions:
T = 298 K
PNO=1.00×10−6���=1.00×10−6 atm
PO3=2.00×10−6��3=2.00×10−6 atm
PNO2=1.00×10−7���2=1.00×10−7 atm
PO2=1.00×10−3��2=1.00×10−3 atm
The standard free energy change (ΔG°) for the reaction NO₍g₎ + O₃₍g₎ → NO₂₍g₎ + O₂₍g₎ is -301.7 kJ/mol.
To calculate the reaction free energy change (ΔG) under the given conditions, we use the equation:
ΔG = ΔG° + RTln(Q)
where Q is the reaction quotient, R is the gas constant, and T is the temperature in Kelvin.
First, we calculate the reaction quotient Q:
Q = (PNO₂)(PO₂) / (PNO)(PO₃)
Substituting the given pressures, we get:
Q = (1.00×10⁻⁷)(1.00×10⁻³) / (1.00×10⁻⁶)(2.00×10⁻⁶) = 0.05
Next, we substitute the values of ΔG°, R, T, and ln(Q) into the equation to calculate ΔG:
ΔG = -301.7 × 10³ J/mol + (8.314 J/mol·K)(298 K) ln(0.05)
ΔG = -315.6 kJ/mol
Therefore, the reaction free energy change (ΔG) for the given conditions is -315.6 kJ/mol. Since ΔG is negative, the reaction is spontaneous under these conditions.
To know more about standard free energy refer here:
https://brainly.com/question/13625901#
#SPJ11
What causes the current to flow?
A) voltage similiarties between two points
B) current similiarties between two points
C) points of equal resistance
D) resistance differences between two points
E) voltage difference between the two points
The main factor that causes the current to flow is the voltage difference between two points. When there is a difference in electrical potential between two points, the flow of electrons or charges in a circuit is initiated. The voltage difference creates an electric field that drives the charges to move from one point to another.
The other options listed, such as current similarities, points of equal resistance, and resistance differences, are important factors in understanding the behavior of the current flow, but they are not the direct cause of the current. Current similarities and points of equal resistance will result in a steady-state current flow, whereas resistance differences will result in a non-uniform current distribution. Therefore, it can be concluded that the answer to the question "What causes the current to flow?" is E) voltage difference between the two points. Understanding this fundamental concept is crucial in the study and application of electrical circuits and electronics.
learn more about voltage here.
https://brainly.com/question/13521443
#SPJ11
Alex and Jamie are planning to build a model boat that can transport a lot of weight. They got their idea by learning about container ships like the one shown below.To model carrying heavy containers across the ocean, their boat needs to be able to carry glass marbles across a small pool. The base of their boat will be made from an empty box. They have several boxes to choose from. Each box is the same size, but they are each made of a different material. Which of these tests should Alex and Jamie do next to pick the best material for the base of their model boat?
A tensile test is a physical experiment that evaluates the suitability of materials.
In general, larger boats are referred regarded as ships. The ability to float in water is the primary characteristic of a successful boat design. The physical force that keeps items like boats and other afloat in liquids is known as buoyancy.
A ship's capacity is determined by its tonnage. The two primary types of ship tonnage are tonnage by weight and tonnage by volume.
A tensile test is a physical experiment that evaluates the suitability of materials for certain engineering or building applications in order to guarantee quality.
To learn more about tensile testing, click:
https://brainly.com/question/14860127
#SPJ1
A small car has a head-on collision with a large truck. Which of the following statements concerning the magnitude of the average force due to the collision is correct? a. The small car experiences the greater average force. b. The small car and the truck experience the same average force. c. It is impossible to tell since the masses are not given. d. The truck experiences the greater average force.
Answer: The answer is B
Explanation: using newton's third laws of motion,the force applied between two objects is same in magnitude and has opposite direction.since two objects have same force,small car has large acceleration than the truck because it has less mass.
N industrial customer with a three-phase, 480 V service entrance is running the following set of loads: • Two 15 HP, 89% efficient lathes, 0. 79 lagging power factor • One 7 ton heat pump' with a COP of 1. 9 and a 0. 95 lagging power factor • Two electric autoclaves, 30 BTU/h, 98% efficient, 0. 97 lagging PF One 25 kW high-intensity discharge (HID) lighting system, unity PF If the lighting system is replaced with a T8 fluorescent system with magnetic ballast that consumes 25% less than the previous system, but introduces a 0. 91 leading power factor, by how much does the service entrance current change? Consider the case when all systems are fully loaded. Consider the AC load under the new lighting regime. Use the NFPA 70 to determine the minimum allowed gauge of the service conductors. Feeder lines are copper, with a 60 °C temperature rating, contained within a raceway with an ambient temperature of 40 °C. Start with article 310. 15; state the specific article(s)/tables used to determine your answer
The minimum allowed gauge of the service conductors would be 1/0 AWG.
To calculate the current at the service entrance, we need to calculate the total power and power factor of the loads.
For the two lathes, the total power is 2 x 15 HP x 0.89 = 26.7 kW, and the power factor is 0.79 lagging. The apparent power (S) can be calculated as S = P / PF = 33.8 kVA.
For the heat pump, the total power is 7 ton x 12,000 BTU/ton x 0.2931 kW/BTU / 1.9 COP = 2.64 kW, and the power factor is 0.95 lagging. The apparent power can be calculated as S = P / PF = 2.78 kVA.
For the two autoclaves, the total power is 2 x 30 BTU/h x 0.98 / 3.412 BTU/kW = 17.5 kW, and the power factor is 0.97 lagging. The apparent power can be calculated as S = P / PF = 18.0 kVA.
For the HID lighting system, the power is 25 kW and the power factor is unity, so the apparent power is equal to the real power, S = P = 25 kVA.
The total apparent power for all loads is S_total = 33.8 + 2.78 + 18.0 + 25 = 79.58 kVA.
If the lighting system is replaced with a T8 fluorescent system that consumes 25% less power, the new power is 0.75 x 25 kW = 18.75 kW. The power factor is 0.91 leading, so the apparent power is S = P / PF = 20.6 kVA.
The new total apparent power for all loads is S_total = 33.8 + 2.78 + 18.0 + 20.6 = 75.18 kVA.
The current can be calculated using the formula I = S / (sqrt(3) x V), where V is the line voltage (480 V):
For the original loads, I_original = 79.58 kVA / (sqrt(3) x 480 V) = 96.4 A
For the new loads, I_new = 75.18 kVA / (sqrt(3) x 480 V) = 91.0 A
Therefore, the change in service entrance current is (91.0 - 96.4) A = -5.4 A.
To determine the minimum allowed gauge of the service conductors, we can use the table in NFPA 70 Article 310.15(B)(16) for 60°C rated conductors in raceways. Based on the calculated current of 96.4 A for the original loads, we would need a minimum of 2/0 AWG copper conductors. However, based on the calculated current of 91.0 A for the new loads, we would only need a minimum of 1/0 AWG copper conductors.
Therefore, the minimum allowed gauge of the service conductors would be 1/0 AWG.
Learn more about service conductors
https://brainly.com/question/28298618
#SPJ4
today, this part of kansas is rolling hills and farm fields. describe the environment ni which the sediment ni this rock sample (photograph )x was deposited there about 290 million years ago.
The environment was quite different. Based on the sediment in the rock sample (photograph X), it is likely that this area was once covered by a shallow sea or ocean. The presence of fine-grained sediment, such as silt and clay, suggests that the water was relatively calm and quiet.
About 290 million years ago, during the Paleozoic era, Kansas was covered by a shallow sea known as the Permian Sea. The sedimentary rocks found in Kansas, including limestone, sandstone, and shale, were deposited in this sea over millions of years.
The environment in which sediment is deposited can provide clues about the conditions of the area at the time. Based on the type of rock you mentioned, it is likely that the sediment was deposited in a marine environment, such as a shallow sea or a shoreline. The limestone could have been formed from the accumulation of shells and other organic material from marine organisms, while the sandstone and shale could have been deposited by erosion and transport of sediment from nearby land.
In terms of the landscape, it is possible that the area that is now Kansas was a low-lying coastal plain, with rivers and streams carrying sediment into the sea. The rolling hills and farm fields seen today are a result of more recent geologic processes, such as erosion and deposition by wind and water.
Overall, the sediment in the rock sample you mentioned was likely deposited in a marine environment in what is now Kansas, during the time period of the Permian Sea.
Learn more about the Paleozoic era:
https://brainly.com/question/1972972
#SPJ11
0.03 Volts =
A) 3 microvolts
B) 30 millivots
C) 3 Volts
D) 300 Volts
E) 30 millivolts
The0.03 volts are equal to 30 millivolts. The prefix "milli" denotes a factor of 1/1000, while the prefix "micro" denotes a factor of 1/1,000,000. Therefore, 0.03 volts is larger than 3 microvolts (which is 0.000003 volts), but smaller than 3 volts and 300 volts.
The correct answer is option E, which states that 0.03 volts is equal to 30 millivolts. A millivolt is one-thousandth of a volt, so multiplying 0.03 volts by 1000 gives the answer of 30 millivolts. Millivolts are commonly used to measure small voltage changes, such as those in biomedical signals, whereas volts are used to measure larger electrical potentials. Therefore, understanding the relationship between volts and millivolts is important for accurately measuring and interpreting electrical signals in various applications.
learn more about millivolts here.
https://brainly.com/question/26666535
#SPJ11
A motor cycle travelling at 100km/h on a flat road applies the brakes at 0.80m/s² for 1 minute. How far did the motorcycle travel during this time?
Answer: 228 meters
Explanation: D=vIxt+1/2At^2
Bohr developed an equation for calculating the energy levels of a hydrogen atom. Which of the following can be determined using this equation? Select all that apply.
The energy needed to remove an electron completely from the hydrogen atom
The difference in energy between two energy levels in a hydrogen atom
The wavelength of a line in the atomic line spectrum for hydrogen
Bohr's equation enables us to determine the ionization energy, energy differences between energy levels, and the wavelengths associated with the atomic line spectrum for hydrogen atoms.
Bohr's equation for calculating the energy levels of a hydrogen atom provides valuable information about the atom's behavior. Using this equation, we can determine the following:
1. The energy needed to remove an electron completely from the hydrogen atom: Bohr's equation helps calculate the ionization energy, which is the amount of energy required to detach an electron from its lowest energy level (n=1) to infinity.
2. The difference in energy between two energy levels in a hydrogen atom: The equation calculates the energy levels for different orbits (n values), and by finding the difference between the energy levels, we can determine the energy gap between them.
3. The wavelength of a line in the atomic line spectrum for hydrogen: When an electron transitions between energy levels, it either absorbs or emits a photon. The energy of the photon corresponds to the difference in energy between the two levels. Using this information and the Rydberg formula, we can calculate the wavelength of the emitted or absorbed light, which corresponds to a line in the atomic line spectrum for hydrogen.
For more such questions on Bohr's equation.
https://brainly.com/question/31251303#
#SPJ11
a body is in mechanical equilibrium when it is being moved by a constant force the sum of the external forces and the sum of the external torques acting on it is zero it is moving with constant acceleration the sum of the external forces acting on it is zero the sum of the external torques acting on it is zero
A body is in mechanical equilibrium when the (c) sum of the external forces acting on it is zero. This means that the body is not accelerating and its angular velocity is not changing. In other words, the body is in a state of rest or moving with a constant velocity.
When a body is in mechanical equilibrium, the net force acting on it is zero, which means that the body is not accelerating. This is because the body experiences equal and opposite forces that cancel each other out, resulting in a net force of zero.
In addition, when a body is in mechanical equilibrium, the net torque acting on it is zero, which means that the body is not rotating or its angular velocity is not changing. This is because the body experiences equal and opposite torques that cancel each other out, resulting in a net torque of zero.
To summarize, a body is in mechanical equilibrium when the sum of the external forces and the sum of the external torques acting on it is zero. This means that the body is not accelerating and its angular velocity is not changing. A common example of a body in mechanical equilibrium is an object at rest on a flat surface, where the force of gravity is balanced by the normal force exerted by the surface.
To know more about the mechanical equilibrium refer here :
https://brainly.com/question/14246949#
#SPJ11
A body is in mechanical equilibrium when
A.it is moving with constant acceleration.
B.it is being moved by a constant force.
C.the sum of the external forces acting on it is zero.
D.the sum of the external torques acting on it is zero.
E.it is moving with constant linear velocity and rotating with a constant angular velocity.
A solenoid of radius 2. 5 cm has 400 turns and a length of 20 cm. Find (a) its inductance and (b) the rate at which current must change through it to produce an emf of 75 mV
a. The inductance of the solenoid is 0.0556 H
b. The rate of change of current to produce an emf of 75 mV is -1.35 A/s.
a) The inductance of a solenoid can be calculated using the formula L = (μ₀n²πr²l) / (2l + 3r), where μ₀ is the permeability of free space, n is the number of turns per unit length, r is the radius, and l is the length of the solenoid.
Plugging in the values given, we get
L = (4π x [tex]10^{-7}[/tex] x 400² x π x 0.025² x 0.2) / (2 x 0.2 + 3 x 0.025) = 0.0556 H.
b) The emf induced in a solenoid can be calculated using the formula emf = -L(dI/dt), where L is the inductance and dI/dt is the rate of change of current.
Solving for dI/dt, we get dI/dt = -emf/L. Plugging in the values given,
we get dI/dt = -(75 x [tex]10^{-3}[/tex] V) / 0.0556 H = -1.35 A/s.
So the rate at which current must change through the solenoid to produce an emf of 75 mV is 1.35 A/s.
Learn more about the solenoid at
https://brainly.com/question/15576393
#SPJ4
The question is -
A solenoid of radius 2.5 cm has 400 turns and a length of 20 cm. Find
a) its inductance and
b) the rate at which current must change through it to produce an emf of 75 mV.
circular loop of wire 50 mm in radius carries a current of 100 a. find the (a) magnetic field strength and (b) energy density at the center of the loop.
(a) The magnetic field strength at the center of the loop is 4π × [tex]10^{-4[/tex] Tesla, and (b) The energy density at the center of the loop is 1.6 × [tex]10^3[/tex] Joules per cubic meter.
(a) To find the magnetic field strength at the center of a circular loop of wire, we can use the Biot-Savart law, which relates the magnetic field at a point to the current flowing through a nearby wire segment. For a circular loop, the magnetic field at the center is given by:
B = μ₀I/2R
where μ₀ is the permeability of free space, I is the current flowing through the loop, and R is the radius of the loop. Substituting the given values, we get:
B = (4π × [tex]10^{-7[/tex] T·m/A) × (100 A)/(2 × 0.05 m) = 4π × [tex]10^{-4[/tex] T
Therefore, the magnetic field strength at the center of the loop is 4π × [tex]10^{-4[/tex] Tesla.
(b) To find the energy density at the center of the loop, we can use the equation for magnetic energy density, which relates the magnetic field strength to the energy per unit volume of the magnetic field. The energy density is given by:
u = B²/2μ₀
Substituting the magnetic field strength we found in part (a), we get:
u = (4π × [tex]10^{-4[/tex] T)²/(2 × 4π × [tex]10^{-7[/tex] T·m/A) = 1.6 × [tex]10^3[/tex] J/m³
Therefore, the energy density at the center of the loop is 1.6 × [tex]10^3[/tex] Joules per cubic meter.
In summary, the magnetic field strength at the center of the loop is 4π × [tex]10^{-4[/tex] Tesla, and the energy density at the center of the loop is 1.6 × [tex]10^3[/tex] Joules per cubic meter. These values are important for understanding the behavior of magnetic fields and their interactions with other objects in the vicinity of the loop.
For more such questions on Magnetic field strength.
https://brainly.com/question/29754188#
#SPJ11
if a person tries to induce a fire on an object by focusing sun light using a concave mirror. the object should be placed:
When a person tries to induce a fire on an object by focusing sunlight using a concave mirror, the object should be placed at the focal point of the mirror. Concave mirrors have a curved surface that reflects light inward, converging the rays to a single point called the focal point.
In this scenario, the sunlight acts as a source of parallel rays that are reflected off the concave mirror's surface. As these rays converge, they create an intense concentration of heat at the focal point. By placing the object at this location, it will receive the maximum amount of heat energy from the focused sunlight, increasing the likelihood of ignition.
To find the focal point, one can use the mirror's focal length, which is the distance between the mirror's vertex and the focal point. The focal length is typically provided by the manufacturer or can be experimentally determined. It is essential to ensure that the mirror is correctly aligned with the sunlight, so the rays are parallel to the mirror's principal axis to achieve optimal focus and heating.
In summary, to induce a fire on an object using a concave mirror, the object should be placed at the mirror's focal point, where the sunlight's rays are focused and heat is maximized. Proper alignment of the mirror with sunlight and knowledge of the mirror's focal length is crucial for a successful ignition.
For more such questions on Concave mirror.
https://brainly.com/question/3359672#
#SPJ11
The Fungi kingdom does not include _____.
molds
bacteria
yeast
mushrooms
The Fungi kingdom does not include bacteria. Option B is correct.
Bacteria belong to a separate kingdom called the Monera, which includes all unicellular prokaryotic organisms. The Fungi kingdom includes organisms such as molds, yeast, and mushrooms, which are eukaryotic organisms that obtain nutrients by absorbing organic matter from other organisms in their environment.
Fungi obtain nutrients by absorbing organic matter from their environment. They are heterotrophic organisms, which means that they do not produce their own food through photosynthesis like plants. Instead, they secrete enzymes that break down complex organic compounds in their environment into smaller molecules that can be absorbed through their cell walls.
Fungi play important roles in many ecosystems. They are essential decomposers, breaking down dead organic matter and recycling nutrients back into the environment. Some fungi also form mutualistic relationships with other organisms, such as mycorrhizal associations with plant roots, where they help plants absorb nutrients from the soil. Option B is correct.
To know more about the Fungi, here
https://brainly.com/question/329225
#SPJ1
Which of these is most likely to be a centrifugal force within the EU in the future?
Among the given options, cultural differences are most likely to be the centrifugal force within the EU in the future. The EU is a political and economic union of 27 member states, and cultural differences among its member states have always been present.
With the increasing number of immigrants from different parts of the world, the cultural differences among EU member states are becoming more prominent. Each member state has its unique language, history, customs, and traditions, which can create misunderstandings and conflicts among the member states.
The EU aims to promote unity and solidarity among its member states, but cultural differences can lead to a lack of understanding and trust between them. The EU's diverse cultural heritage is both a strength and a challenge for the union. The EU needs to find a way to respect the cultural diversity of its member states while maintaining its unity.
However, the cultural differences among the member states can still cause tensions and conflicts in the future. Therefore, it is crucial for the EU to continue to foster cultural awareness and understanding among its member states to maintain the union's cohesion and stability.
learn more about centrifugal force Refer: https://brainly.com/question/14467048
#SPJ11
complete question:
Which of these is most likely to be a centrifugal force within the EU in the future?
a. trade barriers
b. closed borders
c. pollution problems
d. cultural differences
What is the wavelength of a 256-hertz sound wave in air at STP?
A: 1.17 x 10⁶ m
B: 1.29 m
C: 0.773 m
D: 8.53 x 10⁻⁷ m
Answer:
V = 331 m/s speed of sound in dry air
λ = V / f = 331 m/s / 256 / s = 1.29 m
(B) is correct
80mg/dL or 0.08g/dL is equal to how many drinks?
The amount of drinks that would result in a blood alcohol concentration (BAC) of 0.08g/dL or 80mg/dL depends on various factors such as weight, gender, and the amount of time between drinks.
However, on average, it takes about 2-3 drinks for a person weighing around 150 pounds to reach a BAC of 0.08g/dL. It is important to note that different types of alcoholic beverages contain different amounts of alcohol and may affect BAC differently. Therefore, it is important to drink responsibly and always have a designated driver or plan for a safe way home. Hi! The number of drinks corresponding to a blood alcohol concentration (BAC) of 80mg/dL or 0.08g/dL varies depending on factors such as weight, gender, and the time frame in which the drinks are consumed. However, on average, a BAC of 0.08g/dL can be reached by consuming approximately 4 standard drinks within 1-2 hours for a 160-pound male or 3 standard drinks for a 120-pound female. Remember that this is just an estimate, and individual responses may vary.
Learn more about alcohol here
https://brainly.com/question/947751
#SPJ11
Three point charges are located on the x-axis at the following positions: Q1 = +2. 00 μC is at x = 1. 00 m, Q2 = +3. 00 μC is at x = 0. 00, and Q3 = -5. 00 μC is at x = -1. 00 m. What is the magnitude of the electric force on Q2?
The negative sign indicates that the force is in the opposite direction to the positive direction of the x-axis (i.e., to the right).
The electric field due to Q1 at the position of Q2 is:
E1 = kQ1 / r1²
E1 = (9.0 x [tex]10^9[/tex] N·m²/C²) x (+2.00 x [tex]10^{-6}[/tex] C) / (1.00 m)²
= 1.8 x [tex]10^4[/tex] N/C (to the left)
The electric field due to Q3 at the position of Q2 is:
E3 = kQ3 / r3²
E3 = (9.0 x [tex]10^9[/tex] N·m²/C²) x (-5.00 x [tex]10^{-6}[/tex] C) / (1.00 m)²
= -4.5 x [tex]10^4[/tex] N/C (to the right)
Etotal = E1 + E3
= (1.8 x[tex]10^4[/tex] N/C) + (-4.5 x [tex]10^4[/tex]N/C)
= -2.7 x [tex]10^4[/tex]N/C (to the right)
F = QE
where Q is the charge of the particle. For Q2, we have:
F2 = Q2Etotal
= (3.00 x [tex]10^{-6}[/tex] C)(-2.7 x [tex]10^4[/tex] N/C)
= -8.1 x [tex]10^{-2}[/tex] N
The magnitude of the electric force on Q2 is therefore:
|F2| = 8.1 x [tex]10^{-2}[/tex]N
The electric field is a fundamental concept used to describe the influence that electric charges have on each other. An electric field is defined as the force per unit charge that a charged particle experiences in the presence of other charged particles. Electric fields have many applications in modern technology, including electric motors, generators, and electronic devices.
The electric field is a vector quantity, meaning that it has both magnitude and direction. The direction of the electric field is the direction in which a positive test charge would move if it were placed in the field. The electric field is created by electric charges, either by stationary charges or by moving charges. The strength of the electric field at any point in space depends on the amount and distribution of the charges creating the field. The unit of electric field is newton per coulomb (N/C) in the SI system.
To learn more about Electric fields visit here:
brainly.com/question/15800304
#SPJ4
plsssss help me ........
Answer:
silk-ties fabric
rubber-rubber bands
cellulose-jeans
starch-food and paper
dna-genetic
Explanation:
in a movie, tarzan evades his captors by hiding under water for many minutes while breathing through a long, thin reed. assume that the maximum pressure difference his lungs can manage and still breathe is -71 mm m m -hg h g . 1 mm m m -hg h g
Tarzan's ability to breathe through a long, thin reed while hiding under water for many minutes in the movie is quite impressive.
This technique is known as snorkeling and involves breathing through a tube while floating on the surface of the water.
The maximum pressure difference that his lungs can manage and still breathe is -71 mm Hg, which means that he can handle a drop in pressure of up to 71 millimeters of mercury below atmospheric pressure.
This is important because as he breathes through the reed, the pressure inside his lungs decreases, allowing air to flow in. However, if the pressure drops too low, his lungs will not be able to handle it and he will not be able to breathe.
Therefore, it is crucial that he does not stay under water for too long and that he is careful not to inhale too deeply. Overall, Tarzan's ability to use a reed to breathe underwater is a remarkable feat of human ingenuity and survival.
To know more about pressure refer here:
https://brainly.com/question/30673967#
#SPJ11
the maximum tailwind component of the airplane is 10 knots. the actual tailwind calculated is 11 knots. other aircraft are continuing to land, so you decide to ignore the limitation and land as well. which hazardous attitude are you displaying?
The hazardous attitude displayed in this situation is "invulnerability."
Invulnerability is the belief that "it can't happen to me" and can lead to a disregard for rules, procedures, and limitations.
In this situation, the pilot is ignoring a limitation on the maximum tailwind component of the airplane and landing with an actual tailwind that exceeds the limitation. This could lead to a loss of control of the aircraft during landing or other safety issues.
It's important for pilots to recognize this hazardous attitude and take steps to mitigate it, such as adhering to limitations and procedures, considering the potential consequences of their actions, and recognizing their own fallibility.
To learn more about invulnerability, click here:
https://brainly.com/question/31211952
#SPJ11
PART OF WRITTEN EXAMINATION:
As oxygen levels increase, polarization tends to ____
A) decrease
B) increase
C) stay the same
As oxygen levels increase, polarization tends to decrease. This is because oxygen is a highly electronegative element, meaning it has a strong attraction for electrons.
As oxygen molecules are introduced to a system, they will attract electrons away from other molecules, causing an overall decrease in polarization. This can have various effects on the system, depending on the specific context. For example, in certain chemical reactions, decreased polarization can lead to a decrease in reactivity or a decrease in the strength of intermolecular forces. However, in other contexts, such as in biological systems, decreased polarization may be beneficial, as it can help to stabilize important molecules like proteins and DNA. Overall, the relationship between oxygen levels and polarization is an important factor to consider in many different scientific fields, and can have a significant impact on the behavior of systems ranging from the smallest chemical reactions to the largest ecosystems.
Learn more about the polarization refer: brainly.com/question/29217577
#SPJ11
"from the coordinates obtained in part b, find the slope of the position-time relationship for the bowling ball using the ""rise over run"" algortithm."View Available Hint(s) 0.40 s 2.5m 2.5m/s 0.40m/s Submit
To find the slope of the position-time relationship for the bowling ball using the "rise over run" algorithm, you'll first need the coordinates obtained in part b. The slope represents the rate of change of position with respect to time, and in this context, it is equal to the ball's velocity.
Using the "rise over run" algorithm, the slope (velocity) can be calculated by dividing the change in position (rise) by the change in time (run). In this case, the coordinates represent the position and time values, with the first coordinate being the initial position and time, and the second coordinate being the final position and time.
Assuming you have two coordinates (x1, y1) and (x2, y2), where x values represent time and y values represent position:
Slope = (y2 - y1) / (x2 - x1)
Once you have the coordinates from part b, plug the values into the formula above to calculate the slope. This will give you the velocity of the bowling ball, which represents the relationship between the position and time for the given motion.
For example, if the coordinates from part b are (0.4 s, 2.5 m) and (0.8 s, 5 m), the slope would be:
Slope = (5 m - 2.5 m) / (0.8 s - 0.4 s) = 2.5 m / 0.4 s = 6.25 m/s
In this example, the slope (velocity) of the position-time relationship for the bowling ball is 6.25 m/s.
learn more about velocity here: brainly.com/question/21729272
#SPJ11
When knee flexion is increased (heel brought to buttocks) during running, the moment of inertia of the lower extremity about the hip: a.cannot be determined without knowing the mass and length of the leg b.remains the same c.is increased d.is decreased
When knee flexion is increased (heel brought to buttocks) during running, the moment of inertia of the lower extremity about the hip: c. is increased.
Moment of inertia is a measure of the resistance of an object to rotational motion, and it depends on the distribution of mass around the axis of rotation. When the knee is flexed and the lower leg is brought closer to the hip, the distribution of mass around the hip joint changes. The lower leg moves from an extended position, where most of the mass is concentrated at the distal end (foot), to a flexed position, where the mass is distributed more evenly along the length of the leg. This redistribution of mass increases the moment of inertia of the lower extremity about the hip. Therefore, when knee flexion is increased during running, the moment of inertia of the lower extremity about the hip is increased.For more such question on moment of inertia
https://brainly.com/question/3406242
#SPJ11
The phenomenon that causes the position of the Earth's celestial poles to move among the stars called
The phenomenon that causes the position of the Earth's celestial poles to move among the stars is called precession.
Precession is a slow and gradual wobbling of the Earth's rotational axis caused by the gravitational pull of the Sun and Moon on the Earth's equatorial bulge. This means that over time, the North and South celestial poles appear to move in a circle among the stars. In addition to the precession, the Earth's axial tilt (the angle at which the Earth's North Pole is tilted relative to the plane of the ecliptic) also changes as the precession cycle goes through its 26,000-year period. This causes the position of the celestial poles to move among the stars at a rate of approximately 50 arc seconds per year.
To learn more about stars click here https://brainly.com/question/14354741
#SPJ11
A 1. 8-m-long, 1. 0-mm-diameter steel string is pulled by a 3. 3 × 103 n tension force. By how much is the string stretched, in mm? the young's modulus for steel is 20 × 1010 n/m2
The steel string is stretched by 0.06 mm.
We can use Hooke's Law to find the amount of stretch in the steel string:
F = kΔL
where F is the tension force, k is the spring constant (related to the Young's modulus), and ΔL is the amount of stretch.
Rearranging the equation, we get:
ΔL = F / k
The spring constant k can be expressed as:
k = A * E / L
where A is the cross-sectional area of the string, E is Young's modulus, and L is the original length of the string.
Substituting the given values, we get:
A = [tex]πr^2 = π(0.5 mm)^2 = 0.785 mm^2[/tex]
k = (π/4) * (1.0 mm)^2 * (20 × [tex]10^10 N/m^2[/tex]) / (1.8 m) = 5.50 × [tex]10^4 N/m[/tex]
Now we can find the amount of stretch:
ΔL = (3.3 × [tex]10^3 N)[/tex]/ (5.50 × [tex]10^4 N/m[/tex]) = 0.06 mm
Therefore, the steel string is stretched by 0.06 mm.
Learn more about Hooke's Law
https://brainly.com/question/29126957
#SPJ4
You apply an input force of 12.5 N to the nutcracker while the output force is 50.0 N. What is the actual mechanical advantage of the nutcracker?
Answer:
The mechanical advantage (MA) of a machine is the ratio of the output force to the input force. In this case, the output force is 50.0 N and the input force is 12.5 N, so we can use the formula:
MA = output force / input force
MA = 50.0 N / 12.5 N
MA = 4
Therefore, the actual mechanical advantage of the nutcracker is 4