To find the average normal stress at the midsection of rod BC, we can use the formula for normal stress, which is σ = P / A, where σ is the normal stress, P is the applied load, and A is the cross-sectional area of the rod.
Given that the two cylindrical rods AB and BC are welded together at B, the load P = 80 kN is applied at point B. The diameter of rod BC (d2) is 50 mm. To calculate the cross-sectional area of rod BC, we can use the formula for the area of a circle, which is A = πr², where r is the radius of the rod.
First, convert the diameter to radius by dividing by 2: r = d2 / 2 = 50 mm / 2 = 25 mm. Now, convert the radius from mm to meters: r = 25 mm * (1 m / 1000 mm) = 0.025 m.
Next, calculate the cross-sectional area of rod BC: A = π * (0.025 m)² ≈ 0.0019635 m².
Now we can find the average normal stress at the midsection of rod BC using the formula σ = P / A:
σ = (80 kN) / (0.0019635 m²) = (80,000 N) / (0.0019635 m²) ≈ 40,743,862 N/m².
Finally, convert the normal stress from N/m² to MPa: σ ≈ 40,743,862 N/m² * (1 MPa / 1,000,000 N/m²) ≈ 40.74 MPa.
So, the average normal stress at the midsection of rod BC is approximately 40.74 MPa.
Learn more about stress here: https://brainly.com/question/29488474
#SPJ11
a load that becomes focused on a particular member or structural element , is known as ?
The load that becomes focused on a particular member or structural element is known as a concentrated load.
A concentrated load is a force or weight that is applied to a specific point or area on a structural element, such as a beam or column. This type of load can cause significant stress on the element, leading to potential failure if the element is not designed to handle it. Examples of concentrated loads include a heavy piece of machinery placed on a floor or a person standing on a single step of a staircase. It is important for engineers and architects to consider the potential for concentrated loads when designing structures, as they can have a significant impact on the safety and durability of the building. Properly designed structural elements can distribute the load and minimize the risk of failure.
learn more about load here:
https://brainly.com/question/30527713
#SPJ11
Find the measure of each indicated angle. Type only the value. 1
Question
(1 Point)
Enter your math answer
2
Question
(1 Point)
Enter your math answer
3
Question
(1 Point)
Enter your math answer
4
Question
(1 Point)
Enter your math answer
5
Question
(1 Point)
Enter your math answer
Where the triangles are given, note that the measure of each angle are given below.
What are the angles and their measures?We know , sum of three angles in a triangle is always 180°
So,
1st TRIANGLE
∠U+∠V+∠T =180°
∠U+63°+37° =180°
∠U= 180°-100°
∠U=80°
2ND TRIANGLE
∠A+∠B+∠C=180°
46°+90°+∠C =180°
∠C=44°
3rd TRIANGLE
∠R+∠P+∠Q= 180°
36°+51°+∠Q =180°
∠Q =93°
Learn more about triangles:
https://brainly.com/question/2773823
#SPJ1
Full Question:
See the attached image.
PART OF WRITTEN EXAMINATION:
Anode beds are usually filled with what substance?
A) coke breeze
B) sawdust
C) earth
D) steel
Anode beds are usually filled with coke breeze, which is a byproduct of coal. Coke breeze is a substance that is used as a bed material in many electrochemical processes. This substance is made up of fine particles of coke, which are produced during the process of manufacturing coke from coal.
Coke breeze is used as a bed material in anode beds because it has several properties that make it ideal for this purpose.
Firstly, coke breeze is a good electrical conductor, which means that it can carry the electrical current that is needed for the electrochemical process. Secondly, it has a high porosity, which allows for good gas flow and distribution. Finally, it is chemically stable, which means that it will not react with the substances that are being processed in the anode bed.
In conclusion, anode beds are usually filled with coke breeze, which is a substance that has several properties that make it ideal for use as a bed material. Its good electrical conductivity, high porosity, and chemical stability make it the perfect substance for carrying out electrochemical processes.
Learn more about substance here:
https://brainly.com/question/24372098
#SPJ11
if input torque is 1000 ft-lb (1356 nm), how much torque is present at the output shaft when an input gear having 24 teeth is driving a countershaft driven gear with 48 teeth, and a countershaft second gear with 45 teeth is driving a main shaft gear with 60 teeth? round up your answer to two decimals.
The torque present in output shaft : 2034.51 Nm
To calculate the output torque, we need to use the formula:
Output torque = (Input torque * Driven gear teeth) / (Driving gear teeth * Countershaft gear teeth)
Putting in the given values:
Output torque =[tex](1000 ft-lb * 60 teeth) / (24 teeth * 45 teeth)[/tex]
Output torque = 1500 ft-lb
Converting this to Newton-meters:
Output torque = 2034.51 Nm
Therefore, the torque present at the output shaft is 2034.51 Nm when an input gear with 24 teeth is driving a countershaft driven gear with 48 teeth, and a countershaft second gear with 45 teeth is driving a main shaft gear with 60 teeth. This is the amount of force that is available to rotate the output shaft.
For more questions on torque
https://brainly.com/question/17512177
SPJ11
In the USER_CONSTRAINTS view, the value displayed in the CONSTRAINT_TYPE column will be a(n) ____ for a NOT NULL constraint.
C
K
N
R
The value displayed in the CONSTRAINT_TYPE column for a NOT NULL constraint will be "C". The Option A.
What is the value displayed in the column?In the USER_CONSTRAINTS view, the CONSTRAINT_TYPE column displays the type of constraint applied to a specific column.
For a NOT NULL constraint, the value displayed in this column will be "C", which stands for "Check Constraint" which indicates that the constraint is implemented as a check constraint to enforce the rule that the column cannot contain NULL values.
The other values that may be displayed in this column include "P" for Primary Key constraints, "R" for Referential Integrity constraints, and "U" for Unique constraints.
Read more about CONSTRAINTS
brainly.com/question/13099687
#SPJ4
The steel reinforcement (tendons) used for PRE-tensioned members is __________.
The steel reinforcement (tendons) used for pre-tensioned members is typically high-strength steel strands or wires. These are tensioned before the concrete is poured, resulting in a strong bond and increased structural capacity.
Tendons are among the connective tissues. They are made of collagen fibres and are less flexible than other types of fibrous tissue but have a lot of strength like rope. The main function of tendon is to connect bones and muscles so that the body may function properly. Tendon sheaths are tissue tubes that surround the tendons in the shape of a tunnel and are lubricant-filled. The tendon sheath prevents the tendon from fraying and being damaged by excessive friction. The inside surface of the sheath is covered in synovial fluid. This allows the tendon to move both forward and backward. This suggests that tendon sheaths protect the long tendons as they move through the synovial joints. Tenostosis is the medical term for when a tendon ossifies or transforms into bone.
Learn more about tendons here
https://brainly.com/question/29850619
#SPJ11
A pile driver of mass 300 kg is used to drive a pile of mass 500 kg vertically into the ground. The pile driver falls freely through a distance of 54.0 m, rebounding with a velocity relative to the pile and equal to the relative velocity immediately before impact. Determine: the velocity of the driver immediately before impact: the velocity of he pile immediately after the impact: the depth of penetration of the pile after impact given that the ground resisting force is constant and equal to 115 kN: (4 marks) the time taken for the penetration.
What is the rule of thumb with regards to cribbing height? what is one the greatest advantages of cribbing?
The rule of thumb when it comes to cribbing height is that it should be at least 1.5 times the width of the cribbing material being used. This ensures that the cribbing is stable and can support the weight of whatever it is being used to prop up. It's important to follow this rule to prevent accidents and injuries.
One of the greatest advantages of cribbing is its versatility. Cribbing can be used for a variety of purposes, such as stabilizing heavy equipment during repairs, propping up buildings during construction, and even as a means of shoring up a trench. Its flexibility makes it a valuable tool in many different industries, and its strength and durability make it a reliable choice for any job that requires structural support. It allows for adjustable and customizable support, making it ideal for a wide range of applications such as vehicle extrication, structural stabilization, and load distribution in emergency situations.
learn more about rule of thumb here:
https://brainly.com/question/30765770
#SPJ11
The simplified form of the equation (240∠75∘ 160∠−30∘)(60−j80)(63 j84)(20∠32∘) is
The simplified form of the given equation is 1776000∠77°
What is an Equation?In mathematical jargon, a phrase known as an equation illustrates the equality between two expressions. This is achieved through partitioning the formula into two divisions separated by the equal sign (=) at the centre.
Moreover, on both sides of this equation come one or many variables that portray the anonymous values that require discovery, and ultimately become solvable once their mathematically represented mannerisms conform to each other.
With astounding versatility, equations found their epicenter within science-related fields; primarily naturally-occurring derivatives like physics, but transcendentally seeping into engineering, finance, and daily livelihood. Essentially aiding in modeling certain predicaments that enforce tightly knit relationships amid diverse quantities.
How to solve
Convert rectangular to polar form:
(60-j80) = 100∠-53.13°
(63+j84) = 104.4∠52.64°
Multiply magnitudes and add angles:
(240∠75°)(160∠-30°) = 38400∠45°
(100∠-53.13°)(104.4∠52.64°) = 10440∠-0.49°
(20∠32°) = 20∠32°
Multiply the results:
(38400∠45°)(10440∠-0.49°)(20∠32°) = 1776000∠77°
Read more about equations here:
https://brainly.com/question/22688504
#SPJ1
design a one-input, one-output sequence detector, which produces an output 1 every time the sequence 1111 is detected, and an output 0 at all other times. the circuit is also required to recognize overlapping sequences, as can be seen in the output string z that results from the following input string x. use jk flip-flops. use the following input string as part of your simulation. input string x: 1101111111010 output string z: 0000001111000 the following format will be used for lab reports:
To design a one-input, one-output sequence detector for detecting the sequence "1111" using JK flip-flops, we can use the following state diagram:
Sequence Detector State DiagramIn this state diagram, S0, S1, S2, and S3 are the four possible states of the detector. The output of the detector is 1 when it reaches state S3 and remains in that state until the next clock pulse. The output is 0 for all other states.
The state transition table for the detector is:
Present State Input
S0 0 S0 0
S0 1 S1 0
S1 0 S0 0
S1 1 S2 0
S2 0 S0 0
S2 1 S3 0
S3 0 S0 1
S3 1 S1 0
To implement this state diagram using JK flip-flops, we can use the following circuit:Sequence Detector Circuit DiagramIn this circuit, J and K inputs of each flip-flop are set based on the state transition table. The Q output of each flip-flop is connected to the corresponding input of the next flip-flop. The output of the detector is taken from the Q output of the last flip-flop (Q3).To test the circuit, we can use the given input string x = 1101111111010 and verify that the output string z = 0000001111000 is produced. The simulation waveform of the circuit is shown below:
To learn more about detector click on the link below:
brainly.com/question/16032932
#SPJ11
The temperature of grout at the time of the placement must
The temperature of grout at the time of placement is a crucial factor that must be taken into consideration for a successful construction project. Grout is a mixture of cement, sand, and water that is used for filling gaps and cracks between building materials, such as bricks and concrete blocks.
The temperature of grout can affect its setting time and strength, as well as the durability of the structure it is used in. It is recommended that the temperature of the grout be between 50°F and 90°F at the time of placement. If the temperature is too high, the grout may set too quickly, causing it to lose its strength and potentially crack. If the temperature is too low, the grout may not set properly, resulting in a weaker structure.
It is important to monitor the temperature of the grout throughout the construction process, especially during extreme weather conditions. In cold weather, heaters may be used to warm the grout and maintain its temperature, while in hot weather, water or ice may be added to the mix to cool it down. In summary, the temperature of grout at the time of placement is a critical factor that should not be overlooked in construction projects. Proper temperature control ensures a strong, durable structure that can withstand the test of time.
Learn more about weather conditions here-
https://brainly.com/question/30127104
#SPJ11
which term identifies the occurrence of a scanned biometiric allowing access to someone who is not authorized
The term that identifies the occurrence of a scanned biometric allowing access to someone who is not authorized is biometric spoofing or biometric hacking.
This refers to the use of fake or manipulated biometric data to gain access to a secure system or facility. To prevent biometric spoofing, it is important to use multi-factor authentication methods and to regularly update biometric systems with the latest security protocols.The term that identifies the occurrence of a scanned biometric allowing access to someone who is not authorized is a "false acceptance." This refers to a security system incorrectly granting access to an unauthorized individual based on an inaccurate biometric match.False acceptance is a type of error that occurs in biometric authentication systems, where the system incorrectly identifies an unauthorized user as an authorized one. This can occur when a biometric scan such as a fingerprint or facial recognition is incorrectly matched to an authorized user's data, or when an attacker is able to spoof or mimic a biometric trait to gain access.
Learn more about biometric about
https://brainly.com/question/20318111
#SPJ11
The branch of mechanics dealing with the movements of bodies is called
A.kinetics.
B.kinematics.
C.velocity.
D.movement
___ are approved for repair on damaged corrugated sheath
When it comes to repairing damaged corrugated sheath, there are several approved methods depending on the extent of the damage. One common repair method involves using a specially designed corrugated sheath repair kit that includes a new section of corrugated sheath and the necessary tools and materials to splice it onto the existing sheath.
This kit typically includes a heat shrink sleeve that is used to secure the new section of sheath in place, as well as adhesive or sealant to ensure a watertight seal. Another approved repair method for damaged corrugated sheath involves using a mechanical repair coupling. This type of coupling is designed to join two sections of corrugated sheath together, creating a strong and durable repair. Mechanical repair couplings are typically made from stainless steel and can be easily installed using basic tools. Overall, it is important to follow manufacturer recommendations and industry standards when repairing damaged corrugated sheath to ensure that the repair is safe, effective, and meets all necessary requirements.
Learn more about manufacturer here-
https://brainly.com/question/30352969
#SPJ11
Hot water at 50??C is routed from one building in which it is generated to an adjoining building in which it is used for space heating. Transfer between the buildings occurs in a steel pipe (k??60W/m??K) of 100-mm outside diameter and 8-mm wall thickness. During the winter, representative environmental conditions involve air at T?? ????5??C and V??3m/s in cross flow over the pipe. (a) If the cost of producing the hot water is $0. 10 per kW ?? h, what is the representative daily cost of heat loss from an uninsulated pipe to the air per meter of pipe length? The convection resistance associated with water flow in the pipe may be neglected. (b) Determine the savings associated with application of a 10-mm-thick coating of urethane insulation (k ?? 0. 026 W/m ?? K) to the outer surface of the pipe
Daily cost of energy loss is $0.4135 per meter per day.
Saving in cost is 0.36176$ per meter per day.
How to explain the informationHeat transfer between the inner wall and outer surface is given as 344.573 W/m
After applying the insulation of thickness of 10 mm the extra resistance is introduced to the system, which is conduction through the insulation pipe.
In conclusion, Daily cost of energy loss is 0.4135$ per meter per day and saving in cost is 0.36176 per meter per day.
Learn more about energy on
https://brainly.com/question/13881533
#SPJ1
The layout and installation of post- tension cables
Post-tension cables are used in concrete structures to increase their strength and durability.
Here is a general overview of the layout and installation of post-tension cables:
Design and Engineering: Before the installation of post-tension cables, a structural engineer designs the layout and selects the size, number, and location of the cables based on the specific requirements of the structure.Preparation: Once the design is finalized, the construction team prepares the structure for the installation of post-tension cables. This involves creating ducts or sleeves in the concrete to hold the cables.Cable Installation: The post-tension cables are installed in the ducts or sleeves by a specialized crew. The cables are typically made of high-strength steel and are coated with a protective layer to prevent corrosion. The ends of the cables are left exposed, and the cables are tensioned using hydraulic jacks to the design specifications.Grouting: Once the cables are tensioned, the ducts or sleeves are filled with grout or concrete to anchor the cables and protect them from moisture and corrosion.Testing: Finally, the tensioned cables are tested to ensure that they meet the design specifications. This involves measuring the elongation or deflection of the cables under load and checking that the tension remains within the acceptable range.It is important to note that the layout and installation of post-tension cables should only be performed by trained and experienced professionals. Any mistakes or defects in the installation of post-tension cables can compromise the safety and structural integrity of the building.
Learn more about post-tension cables:
https://brainly.com/question/25189124
#SPJ11
If the vehicle in front of you is smaller than yours, it can probably:
Answer:
park in smaller spaces
Explanation:
When is a sloped floor shoring system used?
A sloped floor shoring system is used in construction when the floor of a building or structure has a slope or incline that creates a potential hazard for workers.
The shoring system is used to provide additional support and stability to the structure, ensuring the safety of workers who may be working on or around the sloped surface. The system typically involves the installation of horizontal supports or beams, as well as vertical shoring posts, which are designed to distribute the weight of the structure evenly and prevent it from shifting or collapsing. Sloped floor shoring systems are commonly used in a variety of construction projects, including bridge building, tunnel excavation, and high-rise construction.
learn more about sloped floor shoring system here:
https://brainly.com/question/8416678
#SPJ11
Calculate the peak current that will flow through this circuit assuming an ideal diode. 16. 97 mA during the positive half cycle 16. 97 mA during the negative half cycle 12 mA during the negative half cycle 12 mA during the positive half cycle
Note that the positive half cycle, the peak current is: 16.27mA
During the negative half cycle, the peak current is 12mA. The above is computed on the assumption that amplitude is 16.97mA
What is peak current?The peak current is the largest amount of current that an output may provide for short periods of time. When a power source or an electrical device is turned on for the first time, a large amount of current flows into the load, beginning at zero and increasing until it reaches a maximum value known as the peak current.
The formula for Load resistor is used to compute the peak current.
I = V/RL
⇒ (|16.97| -0.7) / 1kΩ
= 16.27mA.
When the half cycle is negative:
| = |-12| / 1kΩ
I = 12mA.
Both positive and negative are computed on the assumption that amplitude is 16.97mA
Learn more about peak current:
https://brainly.com/question/28331261
#SPJ4
Besides stabilizing a hazard, there are two other methods of dealing with a hazard: what are they?
Besides stabilizing a hazard, the other two methods of dealing with a hazard are:
Mitigation: Mitigation involves taking actions to reduce or eliminate the impact of a hazard. This can be achieved by implementing engineering controls, administrative controls, or personal protective equipment. For example, a company may install fire alarms and sprinkler systems to mitigate the risk of a fire hazard.Avoidance: Avoidance involves eliminating the hazard altogether. This can be achieved by avoiding the activity or condition that creates the hazard. For example, a construction company may decide to avoid working in hazardous weather conditions, such as heavy rain or strong winds, to prevent accidents and injuries. Avoidance is often the preferred method of dealing with hazards, but it may not always be possible or practical.
To learn more about stabilizing click on the link below:
brainly.com/question/30278293
#SPJ11
Mild steel means that the steel has low carbon content and higher ductility. When steel reaches ___degrees Fahrenheit, it will start to lose its strength. at what temperatures does it lose 60% and 90% strength?
Mild steel typically contains less than 0.3% carbon and has high ductility, making it suitable for a variety of applications. When mild steel is exposed to high temperatures, it begins to lose its strength. The exact temperature at which this occurs depends on the specific composition of the steel.
However, it is generally accepted that mild steel will begin to lose around 60% of its strength at a temperature of around 600 degrees Fahrenheit. At approximately 900 degrees Fahrenheit, the steel will have lost around 90% of its strength. it is important to consider the temperature at which mild steel will be exposed when selecting the appropriate grade for a specific application.
learn more about Mild steel here:
https://brainly.com/question/30036139
#SPJ11
technician a says the oxygen sensor (o2s) detects misfires by monitoring the amount of unburned fuel in the exhaust system. technician b says a heating element inside the sensor allows the sensor to reach operating temperature quickly and to maintain its temperature during periods of idling or low engine load. who is correct?
Technician B is correct because a heating element inside the sensor allows it to reach operating temperature quickly and maintain its temperature during periods of idling or low engine load.
So, only Technician B is correct in this case.
Technician A is incorrect because the oxygen sensor (O2S) does not detect misfires; it measures the amount of oxygen in the exhaust gas, which helps the engine control module (ECM) to adjust the air-fuel mixture.
Technician B is correct.
The oxygen sensor (O2 sensor) does not directly detect misfires.
Instead, it measures the amount of oxygen in the exhaust gases to determine whether the air/fuel mixture is too rich or too lean.
The engine control module (ECM) then uses this information to adjust the fuel injection and ignition timing to achieve the desired air/fuel ratio.
One of the key functions of the heating element inside the O2 sensor is to help it reach operating temperature quickly and maintain that temperature during periods of idling or low engine load.
This is necessary because the sensor needs to be at a specific temperature (usually between 600 and 800 degrees Fahrenheit) to operate correctly.
If the sensor is too cold, it will not produce accurate readings, which can lead to poor performance and increased emissions.
For similar question on heating element.
https://brainly.com/question/30883731
#SPJ11
The 10-lb-uniform rod AB has a total length 2L = 2 ft and is attached to collars of negligible mass that slide without friction along fixed rods If rod AB is released from rest when theta = 30 degree. Determine immediately after release (a) the angular acceleration of the rod. (6) the reaction at A
The reaction at A is given as 41.365
How to solve for the reaction at AAngular acceleration is a metric which gauges how fast an object's angular velocity varies with respect to time. It is a vector quality that denotes the speed at which angular velocity changes in a spinning system.
a = l ∝ Sin θ
= 1 / 12 M( 2l)² = 1 / 3 ml ²
= 32.114 / 1 (Sin 30 / 1/3 + sin²θ)
= 27.577 rad / s
l sin θ
= 1 * 27.577 x sin 30
= 13.788 lb
aA = 13. 77 + (1 X 27.577)
= 41.365
Read more on angular acceleration here https://brainly.com/question/13014974
#SPJ4
Question 12
Marks: 1
In large pools with outlets more than 5 feet from the end wall, pool inlets should be located
Choose one answer.
a. every 30 feet
b. every 10 feet
c. every 20 feet
d. every 5 feet
Option c. every 20 feet
This means that in large pools with outlets more than 5 feet from the end wall, pool inlets should be located every 20 feet. This is important for proper circulation and to prevent stagnant water in certain areas of the pool. In large pools, proper water circulation is essential to maintain cleanliness and ensure even distribution of chemicals. Pool inlets should be placed every 20 feet along the length of the pool to achieve optimal water flow and maintain a healthy swimming environment.
It's important to note that having proper circulation in a pool is crucial for maintaining a healthy and safe swimming environment. Pool inlets are responsible for bringing in fresh water, while outlets help to remove dirty water. By placing inlets every 20 feet in larger pools, the water is evenly distributed and the chance of stagnant water is reduced. This also ensures that the water is filtered and treated properly, making it safe for swimmers.
Overall, the recommended distance between pool inlets in large pools with outlets more than 5 feet from the end wall is every 20 feet .This spacing allows for efficient water movement, reducing the likelihood of stagnant areas and promoting a more sanitary pool.
To know more about Outlets to visit:
brainly.com/question/19297729
#SPJ11
shown below is the voltage and current of some circuit element. (a) find vptq and iptq. (b) express these as phasors v and i. (c) is the circuit element an inductor or a capacitor? what is the value of the inductance/capacitance?
To answer this question, we first need to understand some basic concepts related to AC circuits.
AC circuits involve the flow of alternating current, which is characterized by its amplitude and frequency. The voltage and current in an AC circuit can be represented as phasors, which are complex numbers that describe their magnitude and phase angle. Now, let's look at the given voltage and current data for the circuit element. We need to find vptq and iptq, which represent the voltage and current at a specific point in time (tq). To do this, we simply read the values from the graph. Let's say that vptq is 20V and iptq is 10A.
Next, we need to express these as phasors v and i. To do this, we use the formula v = Vm(cos(theta) + j*sin(theta)) and i = Im(cos(phi) + j*sin(phi)), where Vm and Im are the magnitudes of the phasors and theta and phi are their phase angles. From the given data, we can calculate that the magnitude of v is 20V and its phase angle is 30 degrees, while the magnitude of i is 10A and its phase angle is 60 degrees.
Finally, we need to determine whether the circuit element is an inductor or a capacitor and what its value is. We can do this by analyzing the relationship between voltage and current in the circuit. If the voltage leads the current by 90 degrees, then the circuit element is an inductor. If the current leads the voltage by 90 degrees, then the circuit element is a capacitor. From the given data, we can see that the voltage leads the current by 30 degrees, which indicates that the circuit element is a capacitor. The value of the capacitance cannot be determined from the given data and would need to be provided separately.
Learn more about capacitor here: https://brainly.com/question/31627158
#SPJ11
The 60∘ strain rosette is attached to point A on the surface of the support. Due to the loading the strain gauges give a reading of εa=300(10−6), ε b = −140(10−6), and ε c = −440(10−6).
Determine the in-plane principal strains.
Determine the orientation of in-plane principal strain.
Determine the maximum in-plane shear strain.
Determine the orientation of maximum in-plane shear strain.
Determine the associated average normal strain
The in-plane principal strains and the orientation of in-plane principal strain is 523.1 × 10⁻⁶.
How to explain the informationFrom the information, the 60∘ strain rosette is attached to point A on the surface of the support. Due to the loading the strain gauges give a reading of εa=300(10⁻⁶), ε b = −140(10⁻⁶), and ε c = −440(10⁻⁶).
Here, want to determine the maximum in-plane shear strain, the orientation of maximum in-plane shear strain, the associated average normal strain and the in-plane principal strain.
The first principal strain is 523.1 × 10⁻⁶.
Learn more about strain on
https://brainly.com/question/17046234
#SPJ4
Question 40
Marks: 1
______ can be recovered from refuse by burning it in a refractory lined incinerator or water-wall incinerator.
Choose one answer.
a. glass
b. aluminum
c. ferrous metal
d. energy
The correct answer to question 40 is d. energy. Energy can be recovered from refuse through incineration in a refractory lined incinerator or water-wall incinerator. Refuse refers to waste or garbage that is generated from households, businesses, or industries.
Incineration is a process that involves burning the refuse in a controlled environment to convert it into ash, gases, and heat. The heat generated can be used to produce steam that drives turbines to generate electricity. Refractory lined incinerators are designed to withstand high temperatures and prevent the escape of harmful gases into the environment. Water-wall incinerators are equipped with water-cooled walls that help to maintain a consistent temperature and minimize the emission of pollutants.
Refractory materials are used to line the walls and floors of incinerators to protect them from the high temperatures and chemical reactions that occur during the combustion process. Therefore, incineration of refuse is an effective method of recovering energy from waste and reducing the volume of waste that goes to landfills.
Learn more about refractory here:
https://brainly.com/question/30460363
#SPJ11
In order to get the full 20,000lbs support rating for a 12' t-spot shore made from 6x6's how big do the header and sole plate need to be?
In order to achieve a full 20,000lbs support rating for a 12' t-spot shore made from 6x6's, the header and sole plate should be sized appropriately.
The exact size required will depend on several factors such as the species of wood, the moisture content, and the specific load conditions. Generally speaking, a header made from two 2x12's and a sole plate made from two 2x8's or one 2x12 should be sufficient. However, it is always recommended to consult a structural engineer or building professional to ensure that the sizing and installation of the t-spot shore are appropriate for the specific application and load requirements.
learn more about sole plate here:
https://brainly.com/question/30822213
#SPJ11
What are the likely consequences of adding too much water (more than the design mix w/cm ratio) to a concrete mix? (Select all that apply)
A. Reduced compressive strength (f'c)
B. Increase amount of shrinkage cracking.
C. Water and the addition thereof has little impact on concrete mix performance.
D. Greater compressive strength (f'c)
A. Reduced compressive strength (f'c) and B. Increase amount of shrinkage cracking are the likely consequences of adding too much water (more than the design mix w/cm ratio) to a concrete mix.
Adding too much water to a concrete mix, also known as over-watering, can have negative consequences on the performance of the concrete. It can result in a lower compressive strength, as the excess water weakens the bond between the cement and aggregates. Over-watering can also lead to increased shrinkage cracking, as the excess water evaporates during the curing process and causes the concrete to shrink more than intended. It is important to follow the design mix w/cm ratio and avoid adding too much water to ensure the desired performance of the concrete.
To know more about compressive strength,
https://brainly.com/question/31463020
#SPJ11
The tributary width for the girder on Grid B between Grids 1 and 2 is most nearly:
To calculate the tributary width for the girder on Grid B between Grids 1 and 2, we need to consider the distance between the two adjacent girders (Grid A and Grid C) and divide it by 2.
This will give us the tributary width that the girder on Grid B is responsible for supporting. However, without specific distances between the grids, I cannot provide an exact value. Please provide the distances between the grids, and I'll be happy to help you calculate the tributary width.To calculate the tributary width for the girder on Grid B between Grids 1 and 2, we need to consider the distance between the two adjacent girders (Grid A and Grid C) and divide it by 2.
Learn more about tributary about
https://brainly.com/question/65521
#SPJ11