what is the duty cycle (in percent) to get an average output of 3.7 v? enter your answer to the 2nd nearest decimal place.

Answers

Answer 1

The formula for duty cycle is as follows:Duty cycle = (Ton / T) * 100,Where Ton is the signal's active time, and T is the signal's total period.As a result, we can use this formula to calculate the duty cycle for the given average output voltage and frequency, as shown below:Duty cycle = (Vav / Vmax) * 100Duty cycle = (3.7 / 5) * 100Duty cycle = 74 percentTherefore, a duty cycle of 74 percent is required to obtain an average output of 3.7 volts.

The PWM signal's average voltage value varies as the duty cycle varies. The average voltage value is directly proportional to the duty cycle.

To get an average output of 3.7 v, what is the duty cycle (in percent)?The duty cycle is the fraction of the total period for which a signal or system is active, expressed as a percentage.

The duty cycle is used to express the relationship between the active time and the inactive time of a signal, for example.A PWM signal's output voltage is determined by the duty cycle. The on-time of the signal and the off-time of the signal can be changed with the duty cycle.

Learn more about duty cycle : https://brainly.com/question/26058582

#SPJ11


Related Questions

true or false: since liquid can be considered as incompressible, the volume flow rates into and out of a steady flow device will remain constant.

Answers

Answer:

True

Explanation:

Since liquid can be considered as incompressible, the volume flow rates into and out of a steady flow device will remain constant. True, For a steady, incompressible flow, since the density is constant, it implies that the total volumetric flow rates entering and leaving a control volume are the same.

which safety hazard are firefighters most likely to find in the space between the ceiling and the roof?

Answers

Firefighters are most likely to find the following safety hazards in the space between the ceiling and the roof: accumulation of combustible material, poor ventilation, and exposure to hazardous chemicals.


Accumulation of combustible materials such as wood, paper, insulation, and other debris can provide fuel for a fire, which can be difficult to contain in a confined space like the one between a ceiling and a roof.

Poor ventilation in this space can make it difficult for firefighters to breathe, and they can be exposed to hazardous chemicals such as asbestos, lead, and dust. Firefighters have to be careful with that.

Learn more about Firefighters : https://brainly.com/question/25483991

#SPJ11

in the context of dynamic person-situation interaction, the main difference between evocation and manipulation is that:

Answers

Manipulation involves the intentional control of a situation by a person, whereas evocation is the process through which people elicit responses from others simply by displaying certain behaviors.

Manipulation is a term used in psychology to refer to the intentional control of a situation or environment by a person. It can be used to gain control over others, influence their behavior, or alter their perceptions.

Manipulation can be positive or negative, depending on the intention of the person doing the manipulating. Some forms of manipulation may involve deception, coercion, or exploitation.

On the other hand, evocation is a process through which people elicit responses from others simply by displaying certain behaviors. This is often done unintentionally, without the person being aware that they are having an impact on others.  

Unlike manipulation, evocation does not involve intentional control over a situation or environment.

Learn more about manipulation here:

https://brainly.com/question/27154551

#SPJ11

technician a says that brake fluid that is allowed to remain uncovered absorbs water. technician b says that if brake fluid is accidentally spilled on a fender of a vehicle, it can damage the paint. who is correct?

Answers

Technician A and Technician B both are correct as brake fluid that is allowed to remain uncovered does absorb water and brake fluid can damage the paint on a vehicle's fender if it is accidentally spilled.

Technician A is correct because brake fluid is hygroscopic, which means it absorbs moisture from the atmosphere. This water can corrode brake parts and lead to failure, as well as increase the fluid's boiling point, leading to brake fade and reduced stopping power.
Technician B is also correct because brake fluid is made up of corrosive materials that can break down paint and other surfaces. If the brake fluid is not cleaned off the fender immediately, it can cause permanent damage to the paint.

You can learn more about corrosive materials at: brainly.com/question/29632416

#SPJ11

calculate the cumulative infiltration and the infiltration rate on a silty clay soil after one hour of rainfall at 1cm/h if the initial effective saturation is 20 percent. assume ponding depth h0 is negligible in the calculations.

Answers

The cumulative infiltration and infiltration rate on a silty clay soil after one hour of rainfall at 1cm/h with initial effective saturation of 20 percent are 252 cm and 4.21 cm/h, respectively.

To calculate the cumulative infiltration and the infiltration rate on a silty clay soil after one hour of rainfall at 1cm/h if the initial effective saturation is 20 percent, we need to first calculate the cumulative infiltration (Icum) and infiltration rate (f). The cumulative infiltration is given by the equation: Icum = h0 + ∫f (dt). Here, h0 is negligible and ∫f (dt) = f x t. So, Icum = f x t.

The infiltration rate can be calculated using the Kostiakov equation: f = K x t1/2. Here, K is the Kostiakov coefficient, which is a function of the initial effective saturation (Si). For a silty clay soil, K = 0.0026 x Si0.5 (cm/min1/2). Thus, in this case, K = 0.0026 x 200.5 = 0.164 cm/min1/2. Since the rainfall intensity is 1 cm/h, t = 1 hour = 60 min. So, the infiltration rate, f = 0.164 x 601/2 = 4.21 cm/h. The cumulative infiltration is Icum = 4.21 x 60 = 252 cm. So, the answers are 252 cm and 4.21 cm/h, respectively.

Learn more about infiltration rate : https://brainly.com/question/28992374

#SPJ11

how does the sovent drainage and waste system operate without the venting piping used in traditional systems?

Answers

The solvent drainage and waste system operates without venting piping by using a combination of air flow and pressure.

Instead of relying on venting piping to exhaust fumes and waste, the system takes in air from the atmosphere and circulates it through the system with a blower or compressor. This creates a pressure difference that drives the solvent out of the system, taking any remaining waste with it. The pressure also keeps odors from escaping and prevents the system from backflowing.

Drainage is the removal of a mass of water either naturally or artificially from the surface or subsurface from a place.

Learn more about drainage : https://brainly.com/question/831589

#SPJ11

what device will produce an electrical current when a turbine is used to rotate an iron core wrapped with a coil of wire near a magnet?

Answers

A device that will produce an electrical current when a turbine is used to rotate an iron core wrapped with a coil of wire near a magnet is a generator.

A generator is a device that uses electromagnetic induction to convert mechanical energy into electrical energy. It operates on the basis of the Faraday Law of Electromagnetic Induction, which states that a current is induced in a conductor that is moving through a magnetic field.

The following components are found in a basic generator:

1) rotating magnetic field 2) rotating armature 3) wires 4) coils 5) commutator 6) brushes

Generators are used in a variety of applications, including power plants, wind turbines, and hydroelectric facilities. They are essential for converting mechanical energy into electricity. They have also been utilized as backup power supplies for homes and businesses.

Learn more about "Magnetic field" at: https://brainly.com/question/23096032

#SPJ11

this is a longitudinal section through the end of a finger. what is the correct name for the area circled in this virtual slide specimen?

Answers

The longitudinal segment through the end of a finger in this virtual slide specimen is known as Hyponychium the tissue located underneath the nail plate.

The hyponychium is the area of skin beneath the free edge of the nail plate, at the distal end of the finger or toe. It is sometimes referred to as the "quick" or the "nail bed seal,"

The hyponychium is an important part of the nail unit and is composed of specialized skin cells that help to support and protect the nail.

The hyponychium plays an important role in protecting the underlying nail bed and fingertip from damage, infection, and other types of trauma. Here are some of the benefits of the hyponychium:

1) Protection: The hyponychium acts as a barrier between the nail bed and the environment, protecting the underlying tissue from injury and infection.

2) Seal: The hyponychium seals the area between the nail plate and the nail bed, preventing dirt, debris, and bacteria from getting underneath the nail and causing infection.

3) Sensation: The hyponychium contains nerve endings that provide sensory feedback to the brain, allowing us to feel pressure, touch, and other sensations

For more such questions on finger

https://brainly.com/question/29891515

#SPJ11

Note- The correct question would be as below

This is a longitudinal section through the end of a finger. What is the correct name for the area circled in this virtual slide specimen?

what is for predict analysis using machine learning? a. data analysis b. data collection c. data engineering d. data science

Answers

For predictive analysis using machine learning, the correct option is (d) data science. The term "data science" is used to describe the techniques and methods employed by statisticians and computer scientists to extract value from data.

It involves obtaining and processing data to provide useful insights, which are then used to make informed business decisions. It is utilized in numerous fields, including healthcare, education, finance, and more. In the field of machine learning, data science is used to build predictive models that aid in the development of algorithms that can anticipate future outcomes.

For example, data science can be used to build a model that predicts which customers are most likely to leave a business, which can be used to create targeted marketing campaigns that incentivize them to stay. Data science is also used to create recommendation engines that predict which products a customer is most likely to purchase based on their purchase history.

Machine learning models have the potential to anticipate future results, while data science can be employed to educate and validate these models.

This necessitates the identification and purification of data, as well as the selection of pertinent variables for the issue at hand. Models are then established and verified for accuracy.

Learn more about machine learning : https://brainly.com/question/25523571

#SPJ11

what is the purpose of the ground symbol used in electrical circuit diagrams? group of answer choices to show that there is a return path for the current between the source of electrical energy and the load. to show the source of electrical energy for the load. to show that there is common bus for connection of the source of electrical energy to the load.

Answers

Answer:

To show that there is a return path for the current between the source of electrical energy and the load.

assuming that the longest stage of 5-stage pipeline requires 0.6ns, and pipeline register delay is 0.1ns, calculate the clock cycle time of 5-stage pipeline and 10-stage pipeline.

Answers

The 10-stage pipeline's clock cycles would take 1.5ns to finish on average, which is 1.5ns longer than the 5-stage pipeline's.

To calculate the clock cycle time of a 5-stage pipeline and a 10-stage pipeline, we need to consider the time required for each stage and the pipeline register delay.

For a 5-stage pipeline with a longest stage of 0.6ns and a pipeline register delay of 0.1ns, the total clock cycle time would be:

Clock cycle time = longest stage time + pipeline register delay = 0.6ns + 0.1ns = 0.7ns

This means that each clock cycle in the pipeline would take 0.7ns to complete.

For a 10-stage pipeline with the same longest stage time and pipeline register delay, the total clock cycle time would be:

Clock cycle time = longest stage time + (pipeline register delay x (number of pipeline stages - 1)) = 0.6ns + (0.1ns x 9) = 1.5ns

This means that each clock cycle in the 10-stage pipeline would take 1.5ns to complete, which is longer than the 5-stage pipeline due to the additional pipeline stages.

It is worth noting that while longer pipelines can potentially increase performance by allowing for higher clock rates, they can also increase the risk of pipeline hazards and decrease overall efficiency due to increased latency and complexity.

To learn more about clock cycles refer to:

brainly.com/question/29673495

#SPJ4

for designing heat exchangers at the pinch, what is the criterion for matching streams above the pinch and what is the criterion for matching streams below the pinch? why are such criteria needed? (10 points)

Answers

The criteria for matching streams above the pinch for designing heat exchangers is to make sure that the hot stream and the cold stream are both having the same temperature. The criteria for matching streams below the pinch is to make sure that the hot stream and the cold stream have the same heat capacity.

These criteria are needed to ensure that there is an efficient heat exchange, meaning that the hot stream will give up most of its heat to the cold stream. In order for this to occur, it is essential that the temperature and heat capacity of the two streams are similar. If the temperatures of the hot and cold streams are too different, the efficiency of the heat exchange will be greatly reduced.

Similarly, if the heat capacities of the hot and cold streams are too different, the heat exchange will not be efficient. Thus, these criteria are necessary for efficient heat exchange.

You can learn more about heat exchangers at: brainly.com/question/22595817

#SPJ11

the equation used to determine the approximate amount of of critical stress to propagate a crack is known as the friffith equation the griffith equation is

Answers

The Griffith equation is used to calculate the approximate amount of critical stress necessary to propagate a crack. The formula for the equation is K = √(πE/2Y), where E is Young's modulus, and Y is the geometrical factor, which depends on the shape of the crack.

The equation is based on the energy release rate for crack propagation and was developed by A.A. Griffith in 1921. The equation is used to calculate the stress intensity factor (K) for a crack in an elastic material.

The Griffith equation is important for engineers as it can be used to estimate how much stress a material can withstand before it will fracture. This is important when designing components or structures that will be subject to loading or fatigue. Additionally, the equation can be used to calculate the stress concentration factor (Kt) at a point of crack initiation.

In conclusion, the Griffith equation is an important equation used to calculate the approximate amount of critical stress necessary to propagate a crack. This equation can be used by engineers to ensure that their designs are able to withstand the expected loads, as well as calculate stress concentration factors.

You can learn more about Griffith at: brainly.com/question/30188283

#SPJ11

Kelvin contact resistance test structure in Fig. P3. 19, it is usually assumed that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm

Answers

In the Kelvin contact resistance test structure in Fig. P3.19, it is usually assumed that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm.

This assumption is made because the purpose of the Kelvin contact resistance test is to measure the resistance of a contact without including the resistance of the contact leads.To achieve this, the current is passed through the current leads, and the voltage is measured using the voltage leads. However, if the voltage leads have any resistance, this will add to the measured resistance value, making it inaccurate. To avoid this, the Kelvin contact resistance test structure uses two sets of voltage leads, one to carry the current and another to measure the voltage, so that any resistance in the measurement leads is not included in the measured resistance value.By assuming that the voltmeter has very high input resistance and there is negligible voltage drop along the voltage measurement arm, the Kelvin contact resistance test structure ensures that any resistance in the measurement leads is insignificant compared to the resistance of the contact being measured. This allows for accurate measurement of contact resistance and is a common technique used in electrical testing.

for more such question on voltage

https://brainly.com/question/1176850

#SPJ11

is represented by a set of / data fields / variables (also known as properties or attributes) with their current value. it is is called____

Answers

In this case, the question is: "is represented by a set of / data fields / variables (also known as properties or attributes) with their current value. it is is called____"

The answer is: An object is represented by a set of data fields or variables (also known as properties or attributes) with their current value. It is called an object.

What is an object?

An object is an instance of a class in object-oriented programming. It is a software bundle of variables and related methods. An object is defined by its class, which determines its attributes (properties or variables) and methods (functions). An object is an instance of a class that has its own identity, state, and behavior.

The state of an object is represented by its attributes, while its behavior is represented by its methods. Therefore, an object is represented by a set of data fields or variables (also known as properties or attributes) with their current value, and it is called an object.

To learn more about  object-oriented programming : https://brainly.com/question/3522354

#SPJ11

Please give a detail explanation, thank you
1) When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies.
True or false
2) If a semi-truck collides head-on with a mini car, which one will exert more force?
Semi-truck on the mini car
Mini car on the semi-truck
There is no force exerted
Both vehicles will exert equal force

Answers

The given statement "When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies" is False and  there is usually some amount of permanent deformation during an impact when semi-truck collides head-on with a mini car.

The statement is False because In reality, there is usually some amount of permanent deformation that occurs during an impact, especially if the impact is severe. However, in many cases, the amount of deformation may be negligible or can be ignored for simplicity in calculations.Therefore the statement is False.

If a semi-truck collides head-on with a mini car then According to Newton's Third Law of Motion, every action has an equal and opposite reaction. Therefore, both the semi-truck and the mini car will exert equal force on each other during a head-on collision. The force experienced by each vehicle will depend on factors such as their mass, speed, and the duration of the impact. However, it is likely that the semi-truck, being much larger and heavier than the mini car, will experience less of a change in velocity than the mini car and therefore will exert more force on the smaller vehicle.

To practice more questions on force:

https://brainly.com/question/12970081

#SPJ11

3
Biocatalysis helps create flavors and scents through what process?
altering DNA

chemical reactions

purifying components in a formula

aiding with the decomposition process

Answers

Answer:

its B. ima keep it short its B

Explanation

what is an impact, ballistic or creep ripple? what is the length of these ripples relative to their heights? how does this ratio compare to those for aerodynamic and hydrodynamic ripples?

Answers

Impact, ballistic, and creep ripples are all types of surface features that can occur on materials subjected to different types of stresses.

Impact ripples are formed when a material is struck by a projectile or another object. Ballistic ripples are similar but are specifically formed by high-velocity projectiles. Creep ripples, on the other hand, are formed when a material is subjected to a constant stress over a long period of time, causing it to slowly deform.

The length of these ripples relative to their heights can vary depending on the specific material and conditions. However, in general, the ripples tend to have a relatively short wavelength compared to their height.

In comparison, aerodynamic and hydrodynamic ripples are formed by the flow of air or water over a surface. These ripples tend to have a much longer wavelength compared to their height, with the length-to-height ratio typically ranging from several to tens of thousands. This is because the fluid flow over the surface is generally much smoother and less abrupt than the stresses that cause impact, ballistic, and creep ripples.

To learn more about stresses refer to:

brainly.com/question/30128830

#SPJ4

a 0.85-hp motor is required by a ducted fan to produce a 24-in stream of air having a velocity of 40 ft/s. estimate the efficiency of the fan.

Answers

A 0.85-hp motor is required by a ducted fan to produce a 24-in stream of air having a velocity of 40 ft/s then the efficiency of the fan is 20.47.

The efficiency of a ducted fan is determined by the ratio of power output (the kinetic energy of the air stream) to the power input (the power of the motor). In this case, the power output can be calculated using the following equation:
Power Output = 0.5 x density of air (in kg per meter cube) x velocity of air (in m/s) x cross-sectional area of air (in meter square) x ( square of velocity of air (in m/s))
Since the velocity of the air is 40 ft/s (which is equivalent to 12.19 m/s), the power output can be calculated as follows:
Power Output = 0.5 x 1.2 kg/m3 x 12.19 m/s x (24 in x 24 in) x (12.19 m/s x 12.19 m/s) = 13024.7 Watts
The power input of the motor can be calculated using the following equation:
Power Input = 0.85 x 746 = 634.1 Watts
Therefore, the efficiency of the fan can be calculated using the following equation:
Efficiency = Power Output / Power Input = 13024.7 Watts / 634.1 Watts = 20.47

You can learn more about efficiency at: brainly.com/question/30280642

#SPJ11

what are the desired characteristics or values for the following parameters of an ideal amplifier? briefly justify your answers. o phase change as a function of the frequency o common mode rejection ratio o input resistance o output resistance

Answers

All the alternatives mentioned are correct, as regards the desired characteristics or values for the parameters of an ideal amplifier.

Here are the desired characteristics or values for the following parameters of an ideal amplifier:

A) Phase shift as a function of frequency: Ideally, an amplifier should have a phase shift of zero across the entire frequency spectrum. This means that the output signal is in phase with the input signal and there is no delay in the signal.

B) Common mode rejection ratio (CMRR): CMRR measures the ability of an amplifier to reject signals that are common to both inputs (such as noise). For an ideal amplifier, the CMRR should be infinite, meaning that it perfectly rejects common-mode signals.

C) Input resistance: An ideal amplifier should have an infinite input resistance. In other words, it should not load down the signal source, and the source should be able to supply the signal without any loss.

D) Output resistance: An ideal amplifier should have zero output resistance, meaning that its output voltage doesn't change regardless of the load connected to its output.

Learn more about amplifier:

https://brainly.com/question/28996974

#SPJ11

a pair of large hydraulically operated shears is attached to the end of the boom on an excavator. the shear is used for cutting steel pipe and i-beams during demotion work. hydraulic cylinder ab exerts an 18kn force on the upper jaw. (a) complete the free-body diagram of the upper jaw, which has been only partially drawn. (b) determine the cutting force f being applied to the pipe.

Answers

Answer:

(a)

Free-body Diagram:

Upper Jaw:

F= 18kN

Friction force

Normal force

(b)

The cutting force f being applied to the pipe is equal to the force exerted by the hydraulic cylinder, 18kN.

A body is projected at 50m/s vertically upwards from the top of a building which is 120m high. Calculate:
i The time taken to reach a point P, 40m above the ground,

Answers

This is about projectiles and the time taken to reach point P, 40 meters above the ground, is approximately 4.04 seconds.

What is the explanation for the above response?

To solve this problem, we can use the kinematic equation that relates displacement, initial velocity, final velocity, acceleration, and time:

y = vi*t + (1/2)at^2

where y is the displacement (in meters), vi is the initial velocity (in meters per second), a is the acceleration (in meters per second squared), and t is the time (in seconds).

At the top of the building, the body has an initial velocity of 50 m/s, which is purely vertical. The acceleration due to gravity is -9.8 m/s^2 (negative because it acts downward).

When the body reaches point P, its displacement from the top of the building is 120 m - 40 m = 80 m.

So, we can use the above equation to find the time taken to reach point P:

80 = 50t + (1/2)(-9.8)*t²

Simplifying and solving for t, we get:

4.04 seconds

Therefore, the time taken to reach point P, 40 meters above the ground, is approximately 4.04 seconds

Learn more about projectiles at:

https://brainly.com/question/13388411

#SPJ1

24. When using grout to fill in the gap between the
concrete and the base plate, be sure to not

Answers

Make sure not to overfill the space when using grout to close the gap between the base plate and the concrete because too much grout can eventually put stress on the concrete foundation and cause harm.

Why are foundation plates equipped with grout holes?

Additionally, the grout hole will stop air pockets from developing beneath the base plate. If dry pack grout is used or the base plate is less than 600 mm long, such a hole is not deemed essential. When welding the column to the base plate, fillet welds are favoured to butt welds.

What is the bare minimal grout space?

Many stone and tile makers advise grout joints to be between 1/8" and 3/16" in size.

To know more about stress visit:

https://brainly.com/question/13261407

#SPJ9

Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers _______________.
A) are more accountable for what students learn
B) have students with a wider variety of learning needs
C) have more special students placed in their regular classrooms

Answers

Option B. In the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs.

According to Dewey, curriculum and institutions should be secondary to children in brain-based pedagogy since learning is socially produced. Students have to apply prior knowledge to generate new meaning in order to effectively learn.

This is what makes individualized instruction complex.Individualized instruction has been emphasized since Dewey's times. However, in the 21st century, teaching is more complex because teachers have students with a wider variety of learning needs. Student-centered learning, on the other hand, has been a popular idea in education for years.

The popularity of student-centered learning can be traced back to John Dewey, a prominent educational philosopher. In Dewey's view, student-centered learning focused on the student's experience, interests, and interaction with the environment. Therefore the correct option is B.

Learn more about "teachers" at: https://brainly.com/question/28328532

#SPJ11

in a steady flow process, the change of total energy of the control volume must . multiple choice question. increase decrease remain zero

Answers

Answer:

remain zero

Explanation:

in a steady flow process, the change of total energy of the control volume must remain zero.

Apart from replacement and displament deep foundations,
1. whats a third soloution and
2 method of installation ,
3. advantages, disadvantages
4. how it is connected to the foundation, then describe the role this connection plays resisting forces (e.g. lateral restraint, and others)

Answers

Alternative deep foundation: helical piles. Installed with torque, ideal for limited access sites, vibration-free. Resist lateral forces.

What is the explanation for the above response?

The third solution for deep foundations is the use of micropiles.Micropiles are typically installed using a drilling rig, and the process involves drilling a small diameter hole (usually less than 30 cm) into the ground and then filling it with a high-strength grout material, followed by the installation of a steel reinforcing element.Advantages of using micropiles include their ability to be installed in low headroom areas, the ability to be installed in difficult soil conditions, and their low noise and vibration during installation. However, their load carrying capacity is typically lower than that of traditional piles, and their installation can be more expensive than other deep foundation solutions.Micropiles are connected to the foundation through a pile cap or a concrete footing, which transfers the load from the structure to the micropiles. The connection between the micropiles and the foundation provides lateral restraint and resists forces such as wind and earthquake loads. The micropiles can also provide uplift resistance, as they are typically installed at an angle to increase their effective length and capacity.

Learn more about deep foundations at:

https://brainly.com/question/29341501

#SPJ1

all of the windings of three phase motors are always wired how?

Answers

Three-phase motor windings can be wired in a delta or star configuration. Delta is for high power, star for low. Configuration depends on motor design and operating requirements.

The windings of a three-phase motor can be wired in either a delta or star (also called wye) configuration.

In a delta connection, the windings are connected in a triangle, with each end of a winding connected to the start of the next winding. This type of connection is commonly used for high voltage and high current applications, as it can handle higher power levels than a star connection.

In a star connection, the windings are connected in a Y shape, with one end of each winding connected to a common point called the neutral or star point, and the other ends of the windings connected to the three-phase power supply. This type of connection is typically used for low voltage and low current applications, as it is easier to connect and provides a neutral point for grounding.

The specific configuration used depends on the motor's design, operating requirements, and the power supply available.

To learn more about Three-phase motor windings:

https://brainly.com/question/26236885

#SPJ11

Which is a small plain text file that a website might place on your local drive?

Answers

Answer:A cookie

Explanation:To track interests.

Technology __________ guides how frequently technical systems are updated, and how technical updates are approved and funded.
a. wrap-up
b. turnover
c. governance
d. changeover

Answers

Technology governance guides how frequently technical systems are updated and how technical updates are approved and funded. Option C is correct.

Technology governance is the framework, policies, and procedures that regulate how an organization's IT infrastructure is managed and monitored. This involves defining how the company's technology-related activities are managed, including decision-making authority, accountability, and access to technology resources.

Technology governance entails establishing IT policies and procedures, providing training and guidance to employees on IT policies and procedures, defining the duties and responsibilities of IT personnel, ensuring regulatory compliance with technology-related laws, and defining how technical systems are updated and authorized for funding.

Technology governance guides how frequently technical systems are updated, and how technical updates are approved and funded.

For instance, it establishes the policies and procedures governing technical change management, risk management, and the decision-making process for technical projects. Technology governance also provides guidance on how to manage the technical resources that are deployed in the organization.

Therefore Option C is correct. Governance guides the technical system.

To learn more about Technology governance :

https://brainly.com/question/14364696

#SPJ11

the low-level wind shear alert system (llwas) provides wind data and software process to detect the presence of a

Answers

The Low-Level Wind Shear Alert System (LLWAS) provides wind data and software processes to detect the presence of hazardous wind shear.

LLWAS (Low-level windshear alerting systems) is a tool with a system to detect the presence of windshears close to the airport, and will provide warning windshear information automatically if has exceeded its threshold.

It works by collecting data from wind speed and direction sensors located around an airport to provide real-time monitoring of changes in wind direction and speed that can lead to hazardous wind shear events. The data is used to create an alert if hazardous wind shear is detected.

Learn more about LLWAS : https://brainly.com/question/30001468

#SPJ11

Other Questions
A non-verbal experiential technique, in which family members position themselves in a tableau that reveals significant aspects of their perceptions and feelings, is known as: which term best fits the following sentence? you are being in a summary when you have given the facts, details, and plot points without showing your opinion. (1 point) responses chronological chronological transitional transitional subjective subjective objective Argumento del cuento crculo de Virgilio Daz grullon u.s. government policies were responsible for chinese immigration to america in the mid-19th century? help I need this asap PLEASE HELP 30 PTS!!!!! Answer the following worksheet questions. 1) Setting: What is the town like and where is it located? What is the culture like? 2) Setting: Where does your main character live? Describe the living space. (could take several paragraphs of detail) 3) Theme: What is the theme for the story and how will you weave it into the plot? What do you want to reader to learn? 4) Symbolism: (optional) What symbols will you use to support your theme and plot? What do they represent and how will you weave them into the story? 5) Tone: (optional) What will your tone be toward each of your three characters, and how will your readers discover these tones? 6) Mood: (optional) What will the mood be in an important scene of your story (quite possibly at the climax)? How will you create this mood? Be descriptive in your explanation. resource spending approach to decision making: a. when is a resource spending approach appropriate? b. what assumptions do this approach make regarding excess capacity? c. what information is gained from this approach? Write an equation to describe the relationship between t, the number of tickets, and c, the total cost of tickets Which industry would most likely not benefit from the applications of biotechnology? PLEASE HELP THIS IS URGENT What is the volume of the composite figure.A. 104ftB. 120ftC. 150ftD. 160ft when fraud risk is significant, and management cooperation is unsatisfactory, the auditors will most likely: Find the product.. a law or regulation affecting a product's characteristics that must be met before a product can enter a country is a: which species will have an ir spectrum? select one or more: nitrogen methane water vapor carbon dioxide oxygen argon Compare5. Review lines 135140 in Scene 4. What does Macbeth realize, and in what way does this speech reveal a change in Macbeths attitude from how he has felt in the past about his deeds? the government sends a $2,000 check to every adult. that is intended to shift aggregate demand to the right, and increase real gdp. true false Select ALL the set of numbers that are possible values for x in the inequality, x what medium had late archaic sculptors begun working in just before the making of the kritios boy and the destruction in athens? what is the chief difference between plasma and serum? what is the chief difference between plasma and serum? concentration of glucose quantity of organic wastes presence/absence of clotting proteins quantity of electrolytes amount of water You do not need to understand margin and markup if you are using value-based pricing. True or False.