A concave lens is shown here. According to the model, a lens disperses rays after passing through it. Which item below most likely uses a concave lens to perform its typical function?

Each aircraft must be moving at a speed of 85.75 km/hr towards each other to hear a pitch that is 2 times the emitted frequency.

What is frequency ?

Frequency is a physical quantity that describes the number of occurrences of a repeating event per unit of time. It is often measured in Hertz (Hz), which represents the number of cycles or vibrations per second.

In the context of waves, such as sound waves or electromagnetic waves, frequency refers to the number of complete cycles of the wave that occur in one second. A high frequency wave has more cycles per second than a low frequency wave.

Frequency is also an important concept in physics, particularly in the study of oscillations and waves. It is used to describe the behavior of systems that oscillate or vibrate, such as a simple pendulum or a guitar string. In these cases, the frequency of the oscillation is related to the natural frequency of the system, which is determined by its mass, stiffness, and other properties.

When two aircraft are moving towards each other, the sound waves from each aircraft are compressed, leading to a higher pitch than the emitted frequency. The pitch heard by the pilots of the aircraft can be calculated using the following formula:

Pitch heard = Emitted frequency * (Speed of sound + Speed of observer) / (Speed of sound - Speed of source)

Since the two aircraft are flying towards each other at the same speed, we can assume that the speed of one aircraft is x km/hr, and the speed of the other aircraft is also x km/hr. Therefore, the relative speed between the two aircraft is 2x km/hr.

Substituting the values given in the formula, we get:

2 * Emitted frequency = Emitted frequency * (343 + 2x) / (343 - x)

Simplifying this equation, we get:

686 - 2x = 343 + 2x

4x = 343

x = 85.75 km/hr

Therefore, each aircraft must be moving at a speed of 85.75 km/hr towards each other to hear a pitch that is 2 times the emitted frequency.

To know more about aircraft visit :-

https://brainly.com/question/5055463

#SPJ1

The correct answer is that solar energy is also known as isolation.

Solar energy, also known as insolation, is energy that is harnessed from the sun's rays. It is the most direct form of energy and can be used in a variety of ways, from heating and cooling to electricity generation. Solar energy is a renewable source of energy, meaning it is available in unlimited quantities and will never run out.


Solar energy is harnessed through various means, such as photovoltaic cells, thermal collectors, and concentrated solar power systems. Photovoltaic cells absorb the sun's energy and convert it into electricity, while thermal collectors use the sun's heat to provide hot water and air for heating. Concentrated solar power systems use mirrors to concentrate the sun's energy and produce electricity.


Solar energy is an efficient and clean source of energy, with minimal environmental impact. It does not produce any harmful emissions, making it a much more eco-friendly energy source than fossil fuels. Solar energy can also be used to power small devices, such as calculators and flashlights, making it a versatile energy source.

Therefore, the correct answer is isolation.

To know more about solar energy, refer here:

https://brainly.com/question/9704099#

#SPJ4

The projectile will be moving at a speed of 57.21 m/s when it reaches the top of its trajectory.

When a projectile is fired at a speed of 138 and an upward angle of 65 degrees, the speed at the top of the trajectory can be calculated. To solve this problem, you need to understand some basic physics concepts. Here's how you can solve this problem:
1. First, identify the given values and write them down:
Initial velocity (u) = 138 m/s
Angle of projection (θ) = 65 degrees
Acceleration due to gravity (g) = 9.81 m/s²
2. Now, break down the initial velocity into its horizontal and vertical components:
Initial velocity in the horizontal direction = u cos θ
Initial velocity in the vertical direction = u sin θ
3. Use the equation of motion to calculate the time taken by the projectile to reach the top of its trajectory:
u sin θ = gt/2
t = 2u sin θ/g
4. Use the time obtained in step 3 to calculate the velocity at the top of the trajectory:
v = u cos θ
Where,
v = final velocity
u = initial velocity
θ = angle of projection
5. Substitute the given values in the equation to get the final answer:
v = u cos θ
v = 138 cos 65
v = 57.21 m/s
for such more question on projectile

https://brainly.com/question/24216590

#SPJ11

Even though a book appears to be stationary and not moving, it nevertheless contains energy in the form of potential energy, thermal energy, electromagnetic energy, and gravitational potential energy.

Energy is a system's ability to accomplish work or produce change. Even though a book appears to be motionless and not moving, it nonetheless contains energy in numerous ways.

The book has potential energy inside its molecular connections. Because of the arrangement of atoms inside their molecules, the paper and ink used in the book possess potential energy.

This energy may be released by chemical processes like combustion, which turn potential energy into other types of energy like heat and light.

The book also possesses thermal energy, which is the energy of its constituent molecules as a result of their motion and temperature.

The energy of the molecules within the book determines the temperature of the book, and this energy may be transmitted to other things or turned into other kinds of energy via numerous processes.

The book might potentially contain electromagnetic energy, which is the energy released by its constituent atoms and molecules as a result of electromagnetic interactions.

Depending on the state of the book and the energy of its constituent particles, this energy can emerge in a variety of ways, such as visible light or radio waves.

Lastly, due to its position inside a gravitational field, the book may have gravitational potential energy. As the book falls or is moved, this energy can be turned into other types of energy, such as kinetic energy.

For more such questions on energy, click on:

https://brainly.com/question/13881533

#SPJ11

The sound level for this noise is approximately 50 decibels.

Sound level is a logarithmic measure of the ratio between the sound pressure level of a particular sound wave and a reference level. The reference level is typically set at the threshold of human hearing, which corresponds to an intensity of 10^-12 W/m^2. The sound level (measured in decibels, dB) of a sound wave is given by,

L = 10 log10(I/I0)

where I is the intensity of the sound wave and I0 is the reference intensity, which is typically set at 10^-12 W/m^2.

So, for an intensity of 10^-7 W/m^2 in a typical classroom, we can calculate the sound level as,

L = 10 log10(I/I0) = 10 log10(10^-7/10^-12) = 10 log10(10^5) = 50 dB

To know more about sound, here

brainly.com/question/30546291

#SPJ4

The final kinetic energy of the block is 308.98 J.

Let's solve the problem using the work-energy theorem.

The work-energy theorem states that the work done on an object is equal to the change in its kinetic energy

W = ΔKE

Initially, the block is at rest. Therefore, its initial kinetic energy is zero.

Ki = 0

We have to find the final kinetic energy of the block. Hence, Kf = ?

Work done on the block

W = Fscosθ

Work done by the applied force,

F = 75 Ns = 8 mθ = 37°

W = Fscosθ

W = 75 × 8 × cos 37°

W = 451.27 J

Work done by the frictional force

Ff = μkFn

The normal force

Fn = mg

Fn = 6 × 9.8

Fn = 58.8 N

Here,

Ff = μkFn

Ff = 0.28 × 58.8

Ff = 16.51 J

Work of friction:

W = Ff × s

W = 16.51 × 8

W = 132.1 J

The total work done on the block,

Wtotal = W + Wfriction

Wtotal = 451.27 + 132.1

Wtotal = 583.37 J

According to the work-energy theorem,

Wtotal = ΔKE

ΔKE = Wtotal

ΔKE = 583.37 J

Final kinetic energy of the block

Kf = KEFinal

Kf = ΔKE

Kf = 583.37 J

Kf = 308.98 J

Therefore, the final kinetic energy of the block is 308.98 J.

Complete question:

A 6 kg block is pushed 8m up a rough 37 degree inclined plane by a horizontal force of 75 N. The initial speed of the block is 2.2 m/s up the plane and a constant kinetic friction force of 25 N opposes the motion. Calculate the fianl kinetic energy of the block.

Learn more about  final kinetic energy at https://brainly.com/question/25959744

#SPJ11

The given statement "an object floating in a container of water and partially submerged has the same density as the water" is true.

When an object is placed in water, it sinks until the weight of the water displaced by the object equals the weight of the object.

If an object has the same density as water, it displaces an equal amount of water to its own weight. When it displaces the same amount of water that has an equivalent mass to the object, it will float partially submerged. If the object's density is greater than water, it will sink. If the object's density is less than that of water, it will float entirely above the water's surface.

Density is defined as the mass of an object per unit volume. The formula for density is mass/volume. Density is a crucial physical property that is used to define and classify materials. The density of an object is determined by its mass and volume. The unit of measurement for density is kg/m3 or g/cm3. The density of water is 1 g/cm3, which is why objects with a density of less than 1 g/cm3 float on water.

An object floating in a container of water and partially submerged has the same density as the water.

To know more about density click here:

https://brainly.com/question/15164682

#SPJ11

The force would be 6 Newtons for a distance of 30 metres.

A force is defined as any influence that results in a change in an object. Distance is the amount of distance that an object moves over time. A force is applied to an item, and the more force is applied, the farther the thing will move.

Action-at-a-distance forces are those that develop even when the two interacting objects are not in close proximity to one another but are nevertheless able to push or pull against one another despite this physical gap.

To know more about Newtons visit:-

https://brainly.com/question/16889018

#SPJ1

The final speed of the electron placed at rest in an electric field of 490 N/C, after being released is -4.558 mega m/s.

Electric field = E = 490 N/C

The force acting on an electron in the electric field is:

F = qE, where q is the charge of the electron and E is the electric field strength.

q = -1.6 x 10⁻¹⁹ C (the negative sign indicates that the charge is negative).

F = qE = (-1.6 x 10⁻¹⁹ C) (490 N/C) = -7.84 x 10⁻¹⁷N.

The acceleration of the electron due to the electric field:

a = F/m = (-7.84 x 10⁻¹⁷N)/(9.11 x 10⁻³¹kg) = -8.6 x 10¹³ m/s².

According to the third law of motion, for every action, there is an equal and opposite reaction. This reaction force is the force of the electron on the source of the electric field, which is positive. Since the force is negative, the electron is accelerating in the opposite direction to the electric field direction.

The velocity can be found from the equation of motion, v = u + at

v = 0 + (-8.6 x 10¹³)(53.0 x 10⁻⁹) = 4.55 x 10⁶ m/s = 4.55 mega m/s.

The final speed of the electron is therefore -4.558 mega m/s.

To know more about speed, refer here:

https://brainly.com/question/17661499#

#SPJ4

Conductor:

Aluminum foil

Insulator:

Plastic

Air

Wood

Soil

Foam

Glass

What is Conductor?

A conductor is a material or substance that allows electric charge to flow freely through it, offering little or no resistance to the flow of an electric current. Common conductors include metals such as copper, silver, and gold.

A conductor is a material or substance that allows electrical current to flow freely through it. This is due to the presence of free electrons that can move easily through the material when an electric field is applied. Common conductors include metals such as copper, silver, and aluminum.

In contrast, an insulator is a material or substance that does not allow electrical current to flow through it easily. Insulators have very few free electrons and resist the flow of electric current. Common insulators include rubber, plastic, glass, and air.

Learn more about Conductor from given link

https://brainly.com/question/24154868

#SPJ1

The time it takes the object to fall through the change in speed using the impulse-momentum theorem is 0.62 seconds.

The impulse-momentum theorem states that the change in momentum of an object is equal to the impulse exerted on it.

To calculate the time it takes the object to increase it speed using the  impulse-momentum theorem, we use the formula below.

Formula:

Recall that F/m = acceleration. Therefore,

Where:

From the question,

Given:

Substitute these values into equation 1 and solve for t

Hence, the time it takes the object to fall is 0.62 seconds.

Learn more about impulse-momentum theorem here: https://brainly.com/question/14121529

#SPJ1

Momentum is not always conserved in real-life situations because external forces can act on a system and change its momentum.

For example, when two cars collide, friction and air resistance can cause the momentum of the system to change. Similarly, when a ball is thrown in the air, gravity and air resistance act on it and cause its momentum to change. Other factors such as deformation, energy loss, and imperfect collisions can also cause momentum to be lost or gained. Therefore, while momentum is a useful concept in physics, it is important to consider the impact of external factors when analyzing real-world situations.

To know more about momentum, here

brainly.com/question/30677308
#SPJ4

It would take approximately 19.2 years for the asteroid to orbit once around the sun. But that none of the answer choices match the calculated value of approximately 19.2 years.

The period (T) of an orbit of a celestial body with semimajor axis (a) around the sun can be calculated using Kepler's third law:

T² = (4π² / GM) * a³

where G is the gravitational constant and M is the mass of the sun.

Plugging in the given value for the semimajor axis (a = 4 AU), we get:

T² = (4π² / (6.674 × 10⁻¹¹ m³/(kg s²) * 1.989 × 10³⁰ kg)) * (4 AU)³

T² = 3.652 × 10¹⁶ s²

Taking the square root of both sides, we get:

T = 6.04 × 10⁸ s

We can convert this time to years by dividing by the number of seconds in a year:

T = (6.04 × 10⁸ s) / (31,536,000 s/year)

T ≈ 19.2 years

Therefore, it would take approximately 19.2 years for the asteroid to orbit once around the sun. The closest answer choice is 16 years.

Learn more about The Period: https://brainly.com/question/12539110

#SPJ11

The first-order maximum for 450-nm wavelength blue light falling on double slits separated by 0.0500 mm is approximately 6.2°.

The angle of the first-order maximum refers to the angle at which the brightest interference pattern appears on a screen placed behind two closely spaced slits when illuminated with the blue light of 450-nm wavelength.

The angle is determined by the equation:

theta_m = (m*lambda)/d

where m is the order, lambda is the wavelength, and d is the slit separation.
theta_m = (1*450E-9 m)/0.0500 mm
theta_m = 6.2°

Thus, the first-order maximum for double slits of 0.0500 mm at 450 nm λ blue light is around 6.2°.

To know more about  first-order maximum click here:

https://brainly.com/question/14703717

#SPJ11

The period of a mass-spring oscillating system undergoing SHM with a period t, when the amplitude is doubled, is still t.

The period of a mass-spring oscillating system undergoing simple harmonic motion (SHM) is determined by the spring constant and mass of the system.

When the amplitude of the system is doubled, the period of the system remains the same, regardless of the amplitude. This means that the period of a mass-spring oscillating system undergoing SHM with a period t, when the amplitude is doubled, is still t.
To understand why the period remains the same, consider the equation for simple harmonic motion:

x(t) = A cos (2πft).

This equation describes the displacement of an object over time and is based on the principle that any system undergoing SHM oscillates about a fixed point at a constant frequency.

The frequency of the system is inversely proportional to the period, and is determined by the spring constant and mass of the system.

Increasing the amplitude of the system does not affect the frequency or period of the oscillations.

For similar question on oscillating system

https://brainly.com/question/14051226

#SPJ11

The process described in the question is known as scenario planning. It is a strategic planning method that involves generating multiple plausible scenarios of future conditions and analyzing the potential impact of each scenario on an organization or a system.

Scenario planning is a useful tool for decision-making, risk management, and identifying opportunities in an uncertain or rapidly changing environment.

By developing a range of scenarios, decision-makers can anticipate potential challenges and opportunities and develop strategies to respond effectively to each situation.

This approach allows organizations to be better prepared and more resilient in the face of future uncertainties. Scenario planning can be applied to various fields, including business, economics, environmental planning, and public policy.

For more details about strategic click here:

https://brainly.com/question/16699515#
#SPJ11

This principle can be observed in other everyday scenarios, such as jumping on a trampoline or the recoil of a gun after firing.  Newton's Third Law of Motion is a fundamental principle in classical mechanics and explains why the spring will bounce when the weight is released.

The bouncing of the weight when released is explained by Newton's Third Law of Motion, which states that for every action there is an equal and opposite reaction. When the weight is released, the spring exerts an equal and opposite force on the weight, propelling it upwards and causing it to bounce. This is because when the weight is pulled down, it compresses the spring, storing potential energy. When the weight is released, the spring decompresses and the potential energy is released, propelling the weight in the opposite direction.

To learn more about Newton's Third Law ;

https://brainly.com/question/25998091

#SPJ11

The given statement " A series circuit is a current divider and a parallel circuit is a voltage divider circuit " is True

In a series circuit, the electric current is the same through each component, and the total current is equal to the sum of the currents through each component. Therefore, the current is divided among the components.

In a parallel circuit, the potential voltage across each component is the same, and the total voltage is equal to the sum of the voltages across each component. Therefore, the voltage is divided among the components.

Know more about electric current here:

https://brainly.com/question/2264542

#SPJ11

The force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is: 0.001 newtons per tesla

The force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is given by the formula F = (μI) / 2πr,

where μ is the permeability of free space, (4π x 10-7 N/A²)

I is current, and r is the radius of the loop.

In this case, the force is (4π x 10-7 x 5.5) / (2π x 0.1) = 0.001 N/T.

In other words, the force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is 0.001 newtons per tesla.

The formula for the force generated per unit field strength on a loop is derived from the fact that the force is a result of the magnetic field generated by the current flowing in the loop.

The magnitude of the magnetic field generated is proportional to the current and inversely proportional to the radius of the loop. Since the force is a product of the current and the magnetic field, it is proportional to the square of the current and inversely proportional to the square of the radius of the loop.

In summary, the force generated per unit field strength on a 20.0 cm wide section of the loop with a current of 5.5 A is 0.001 newtons per tesla, given by the formula F = (μI) / 2πr, where μ is the permeability of free space (4π x 10-7 N/A²), I is current, and r is the radius of the loop.

To know more about force refer here:

https://brainly.com/question/13191643#

#SPJ11

The work done on the block by the spring during its move from its initial position to where the spring has returned to its uncompressed length is[tex]W = (1/2) \times k \times x^2[/tex].

We need to know the spring constant (k) and the displacement of the block (x) from its initial position to the position where the spring has returned to its uncompressed length. We can use the formula:

W = (1/2) * k * x^2

where W is the work done on the block, k is the spring constant, and x is the displacement of the block.

This formula is derived from the potential energy stored in the spring, which is given by:

U = (1/2) * k * x^2

where U is the potential energy stored in the spring.

When the block is initially at rest, the spring is compressed, and it has potential energy given by U = - (1/2) * k * x^2, where x is the initial compression of the spring.

Note that the negative sign indicates that the work done by the spring is negative, which means that the spring is doing work on the block in the opposite direction to the displacement of the block. This is because the spring force is always directed opposite to the displacement of the block.

As the block is released, the spring begins to push it back to its uncompressed length, and the block begins to move.

The work done on the block by the spring is equal to the change in potential energy of the spring, which is given by:

W = U_final - U_initial

Since the final position of the block is where the spring has returned to its uncompressed length, the final potential energy of the spring is zero. Therefore, the work done on the block by the spring is:

W = U_initial

Substituting the initial potential energy of the spring into this equation, we get:

W = (1/2) * k * x^2

Therefore, the work done on the block by the spring during its move from its initial position to where the spring has returned to its uncompressed length is given by the formula:

W = (1/2) * k * x^2

Learn more about spring:

https://brainly.com/question/14670501

#SPJ11

a..... 1.04 x 10⁻⁴ Vi

b.... 9500 V

A) Determine the capacitance (to the nearest 10 μF).

First, we should identify the formula that we will use to solve the problem.

The formula that relates to capacitance is:

C = 2E / V². Where C is the capacitance in farads, E is the energy stored in joules, and V is the voltage across the capacitor in volts.

Converting the energy to joules, we have: E = 250J.

Now we know that the voltage needs to drop to half of its initial value in 10 ms. We can use the following formula to calculate the capacitance: C = R x t / ln(Vi / Vf) where R is the resistance in ohms, t is the time in seconds, Vi is the initial voltage, and Vf is the final voltage, which is half of the initial voltage.

B) Plugging in the given values, we get:

C = 48 x 0.01 / ln(Vi / (Vi / 2))Simplifying and solving for capacitance, we get:

C = 1.04 x 10⁻⁴ ViNow we can use the energy formula to solve for Vi:Vi = √(2E / C)

Plugging in the given values, we get:Vi = √(2 x 250 / 1.04 x 10⁻⁴)Simplifying and solving for Vi, we get:Vi = 9469 V

Therefore, the capacitance that meets these specifications is 100 μF and the initial capacitor voltage that meets these specifications is 9500 V, to the nearest 100 V.

Learn more about capacitance

brainly.com/question/28445252

#SPJ11

Assuming both rocks are thrown from the same height and with the same initial speed, the rock thrown vertically downward will have a larger velocity upon hitting the ground than the rock thrown vertically upward.

This is because the rock thrown upward will lose speed as it moves against the force of gravity. Eventually, the upward motion will be slowed down until the rock reaches the highest point in its trajectory, where it momentarily stops and changes direction. From that point, the rock will accelerate downward, gaining speed as it falls back to the ground. However, the time spent traveling upward and the time spent traveling downward will not be the same, since the upward portion of the trajectory will be slower due to gravity slowing the rock's ascent. This means that the rock thrown upward will have a lower speed when it hits the ground compared to the rock thrown downward.

On the other hand, the rock thrown downward will experience the force of gravity pulling it towards the ground, causing it to accelerate and gain speed as it falls. Since it is initially moving downward, it will not slow down until it hits the ground, meaning that it will have a higher velocity upon impact than the rock thrown upward.

Learn more about force of gravity here: https://brainly.com/question/2537310.

#SPJ11

The term for an orbit that electrons occupy at a fixed distance from the nucleus is called an energy level.

Electrons occupy specific energy levels in an atom, which are determined by the amount of energy required to move an electron from its present energy level to the next higher energy level. The energy levels are designated by a number, which ranges from one to seven. The lowest energy level is one, and the highest energy level is seven.

Electrons in the first energy level are the closest to the nucleus, while electrons in the seventh energy level are the farthest away.

Learn more about energy levels here: https://brainly.com/question/14287666.

#SPJ11

The formula for calculating capacitance is as follows:

C = Q/V

Where,

C = capacitance (Farads)

Q = charge (Coulombs)

V = voltage (Volts)

As given,

Q = 27.0 μC

V = 9.00 V

Substituting the given values in the above equation

C = 27.0 μC/9.00 V = 3.00 μF

Therefore, the value of capacitance is 3.00 μF.

The formula for calculating charge stored is as follows:

Q = CV

Where,

Q = charge (Coulombs)

C = capacitance (Farads)

V = voltage (Volts)

As given,

C = 3.00 μF

V = 12.0 V

Substituting the given values in the above equation,

Q = (3.00 × 10⁻⁶ F) × 12.0 V = 36.0 μC

Therefore, the charge stored is 36.0 μC.

Learn more about  the charge stored at https://brainly.com/question/27393410

#SPJ11

Two forces act on a monkey hanging stationary by a vertical vine: gravity and the tension of the vine. Gravity is the greater force in this situation because it is a constant force that acts downwards.

The two forces that act on a monkey hanging stationary by a vertical vine are tension and gravity. The tension force acts along the vine and pulls the monkey upwards, while the gravity force acts downwards towards the center of the Earth.
If the monkey is stationary, then the two forces are equal in magnitude and opposite in direction. This is because the tension force is balancing the gravity force, resulting in no net force acting on the monkey.

Therefore, if neither of the forces are greater than the other as they are equal in magnitude and opposite in direction.What is tension force?The force exerted by a string, rope, chain, or similar object on another object that it is connected to is referred to as tension. The tension is always directed along the length of the string and away from the object's surface that the string is attached to. When an object is suspended from a rope, the tension force on the rope is equal to the weight of the object (due to gravity), and this tension force is transmitted through the rope to any other objects that the rope is attached to.

For more details about gravity, click on the below link:

https://brainly.com/question/13634821

#SPJ11

The magnitude of the torque on the current loop is calculated using the formula τ=BIA sinθ, where B is the magnitude of the magnetic field, I is the current, A is the area of the loop, and θ is the angle between the magnetic field and the loop's plane. In this case, the magnitude of the torque is τ = (1.2 T)(0.5 A)(5 cm x 5 cm)sin(30°) = 7.5 x 10-3 Nm.

The torque is the rotational force that causes the loop to rotate. This is due to the fact that a force is exerted on the loop by the magnetic field when there is a current running through it. This force generates a torque on the loop, which will cause it to rotate until the angle between the plane of the loop and the magnetic field is 0°.

Know more about torque here

https://brainly.com/question/25708791#

#SPJ11

When a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet, the frictional force exerted by the surface on the crate is 588 N.

When a tired worker pushes a heavy (100-kg) crate that is resting on a thick pile carpet, the frictional force exerted by the surface can be calculated as follows:

The weight of the crate = m × g = 100 kg × 9.8 m/s² = 980 N

Force applied by the worker = F = 600 N

The force of friction acting on the crate is given by the following formula:

Ff = μF

Where, μ is the coefficient of friction, F is the normal force acting on the crate.

Notes: The normal force is equal and opposite to the weight of the crate. i.e., N = 980 N1. The frictional force exerted by the surface on the crate is the static frictional force initially. Hence, we use the coefficient of static friction for our calculation.

2. If the force applied by the worker is not enough to overcome the static frictional force, then the crate will not move and the frictional force will remain static friction.

3. Once the crate starts moving, the static friction will convert to kinetic friction. Hence, we will use the coefficient of kinetic friction if the force applied by the worker is greater than the force of static friction. Initially, the force applied by the worker is less than the force of static friction, hence the frictional force exerted on the crate will be the static frictional force.

Frictional force = Ff = μN

The normal force acting on the crate = Weight of the crate = 980 N

Frictional force =

Ff = μN

= 0.6 × 980 N

= 588 N

Therefore, the frictional force exerted by the surface on the crate is 588 N.

For more such questions on frictional force , Visit:

https://brainly.com/question/4618599

#SPJ11

The force constant of a spring, or spring constant, is  3958.33 kn/m

The force constant of a spring, or spring constant, is a measure of the stiffness of a spring.

The force constant of a spring, the equation F = kx is used, where F is the force applied to the spring, k is the force constant, and x is the amount of displacement.

The force applied to the spring is 475 j and the displacement is 12 cm.

k = F/x = 475 j/0.12 m = 3958.33 kn/m

This means that for every 1 meter the spring is displaced, it exerts a force of 3958.33 kn. The higher the force constant, the more stiff the spring is, meaning that more force is needed to displace the spring.

A  spring with a lower force constant is more flexible, meaning that less force is needed to displace it.

The force constant of a spring is an important factor to consider when designing mechanical systems, as it determines how much force is needed to displace the spring.

It is also important for predicting the amount of force a spring can apply to a given displacement, which is necessary for applications such as machines and vehicles.

to know more about spring constant refer here:

https://brainly.com/question/14670501#

#SPJ11

Final velocity of Jeff's car is 7.133 m/s south. The direction is 59.3° south of east.

In this issue, we can utilize preservation of energy to track down the last speed and course of Jeff's crash mobile after the impact with Julia's. Before the impact, the energy in the x-heading is zero, and in the y-course, it is 60 kg × 4 m/s = 240 kg⋅m/s north. Julia's force is 45 kg × 6 m/s = 270 kg⋅m/s west.After the crash, the energy in the x-course is rationed. The absolute energy in the x-course is as yet zero, as Julia's force that way is likewise zero. In the y-heading, the absolute force after the crash is 60 kg × vj + 45 kg × 2 m/s sin 15°, where vj is Jeff's last speed in the y-course.Utilizing protection of energy, we can compare the force when the crash in the y-heading:

60 kg × 4 m/s + 45 kg × 6 m/s = 60 kg × vj + 45 kg × 2 m/s sin 15°

Working on this situation, we get:

240 kg⋅m/s + 270 kg⋅m/s = 60 kg × vj + 12.19 kg⋅m/s

Addressing for vj, we get:

vj = (240 kg⋅m/s + 270 kg⋅m/s - 12.19 kg⋅m/s)/60 kg

vj = 7.133 m/s south

Consequently, Jeff's last speed is 7.133 m/s south. To find the course, we can utilize geometry. The point of Jeff's last speed concerning the x-pivot is given by:

θ = tan^-1(vj/4 m/s)

θ = 59.3° south of east

Accordingly, the last speed and heading of Jeff's amusement cart are 7.133 m/s at a point of 59.3° south of east.

To learn more about final velocity and direction, refer:

https://brainly.com/question/12634477

#SPJ4

The true statements about the radial (centripetal) acceleration and the tangential acceleration at the end of the blade are: the radial acceleration is non-zero the tangential acceleration is zero

The radial acceleration is non-zero and the tangential acceleration is zero. This is because, the radial acceleration is determined by the formula, ar = (v²)/r

where ar is the radial acceleration, v is the velocity and r is the radius. Thus, since the propeller blade is spinning at a constant rate, the velocity v is constant.

Therefore, the radial acceleration is constant and non-zero.

The tangential acceleration, on the other hand, is given by at = rα

where at is the tangential acceleration and α is the angular acceleration. Since the blade is spinning at a constant rate, the angular acceleration is zero. Therefore, the tangential acceleration is zero.

So, the correct option is the radial acceleration is non-zero and the tangential acceleration is zero.

Learn more about tangential acceleration at https://brainly.com/question/11476496

#SPJ11