A gas is contained in a cylinder with a frictionless moveable piston at a pressure of 2.7 * 105 pascals and a volume of 0.04 cubic meters. What is the work done by the gaseous system if the volume is increased to 0.12 cubic meters ?

There are two forces acting on the rock: the force of gravity pulling it downward and the force of the boulder supporting it from underneath.

The force of gravity is the gravitational attraction between the rock and the Earth. It pulls the rock downward with a force equal to its weight, which is given by the equation Fg = mg, where Fg is the force of gravity, m is the mass of the rock, and g is the acceleration due to gravity (approximately 9.81 m/s^2).

The concept of forces explains why the rock stays on top of the boulder because the forces are balanced. The force of gravity pulling the rock downward is equal and opposite to the force of the boulder supporting it from underneath. As a result, the rock remains in equilibrium, or a state of balance, on top of the boulder. If either force were to change, the equilibrium would be disrupted, and the rock would either fall to the ground or be pushed off the boulder.

To know more about forces visit:-

brainly.com/question/13191643

#SPJ1

(a) The frequency ratio between the two frequencies fi = 256 Hz and f2 = 320 Hz is:

[tex]\frac{f_2}{f_i} = \frac{320}{256} = \frac{5}{4} = 1.25[/tex]

So the frequency ratio is 1.25.

(b) Adding the interval of a fifth to f2 = 320 Hz gives:

fs = f2 * (3/2) = 320 * (3/2) = 480 Hz

The frequency ratio fs/fi is:

[tex]\frac{f_s}{f_i} = \frac{480}{256} = \frac{15}{8} = 1.875[/tex]

So the frequency ratio is 1.875.

(c) To find the frequency of f3, we need to add the interval of a fourth to f2:

f3 = f2 * (4/3) = 320 * (4/3) = 426.67 Hz

Therefore, the frequency of f3 is 426.67 Hz.

The bigger the spring constant, the more stiff or rigid the spring is.

The exact amount of force needed to bend a spring depends on the spring constant. Although pounds/inch is a common measurement in North America, the standard international (SI) unit for spring constants is Newtons/meter. A stiffer spring has a greater spring constant, and vice versa.

The exact amount of force needed to bend a spring depends on the spring constant. Although pounds/inch is a common measurement in North America, the standard international (SI) unit for spring constants is Newtons/meter. A stiffer spring has a greater spring constant, and vice versa.

To know more about spring constant visit:-

https://brainly.com/question/14159361

#SPJ9

Answer:

Astronomers use computer models to simulate the process of galactic evolution through mergers and collisions. These models are based on our current understanding of the physical laws that govern the behavior of matter and energy in the universe. By running simulations of galactic mergers and collisions, astronomers can test their understanding of how these physical processes work in practice and how they contribute to the formation and evolution of galaxies.

One way that astronomers might test their understanding of the physical processes of the universe is by comparing the predictions of their models to observations of real galaxies. For example, if a model predicts that a particular type of galaxy should have a certain shape, size, or distribution of stars, astronomers can compare these predictions to observations of actual galaxies to see if they match up. If there is a discrepancy between the model's predictions and the observations, this can indicate that there are some physical processes that are not well understood or included in the model.

Another way that astronomers might test their understanding is by looking for patterns or trends in the properties of galaxies that are consistent with the predictions of their models. For example, if a model predicts that galaxies that have undergone a recent merger should have a particular distribution of gas and dust, astronomers can look for evidence of this pattern in observations of real galaxies. If they find that the predicted pattern is consistently observed in a large sample of galaxies, this can provide support for the model's predictions and the physical processes that it includes.

Overall, computer models of galactic evolution through mergers and collisions provide a powerful tool for astronomers to test their understanding of the physical processes of the universe. By comparing the predictions of their models to observations of real galaxies and looking for consistent patterns and trends, astronomers can refine their understanding of how galaxies form and evolve over time.

Answer:

Explanation:

The maximum tension the cord can withstand is 69 N, so we know that the tension in the cord cannot exceed this value. The tension in the cord is related to the acceleration of the truck through Newton's second law:

ΣF = ma

where ΣF is the net force on the crate, m is the mass of the crate, and a is the acceleration of the truck.

In this case, the only force acting on the crate in the horizontal direction is the tension in the cord. Therefore, we can write:

ΣF = T = ma

where T is the tension in the cord.

We can solve this equation for the acceleration:

a = T/m

We know that the tension cannot exceed 69 N, so the maximum acceleration the truck can have before the cord breaks is:

a = 69 N / 26 kg

a ≈ 2.65 m/s^2

Therefore, the maximum acceleration the truck can have before the cord breaks is 2.65 m/s^2.

Answer:

The period of a ticker-timer is the time interval between two consecutive dots made by the ticker.

If the frequency of the ticker-timer is 25 Hz, then it makes 25 dots in one second. Therefore, the period of the ticker-timer can be calculated as:

Period = 1/frequency = 1/25 Hz = 0.04 seconds

If the frequency of the ticker-timer is 50 Hz, then it makes 50 dots in one second. Therefore, the period of the ticker-timer can be calculated as:

Period = 1/frequency = 1/50 Hz = 0.02 seconds

So, the period of the ticker-timer is 0.04 seconds for a frequency of 25 Hz and 0.02 seconds for a frequency of 50 Hz

Explanation:

please Mark Me As Brainlist.

Answer:The current in a lightbulb with a voltage of 35.0 V and a resistance of 175 ohm is 0.2 A.

Find the current in a lightbulb?

Given:

The voltage in a lightbulb is given by the equation V=IR

V is the voltage, I is current, and R is the resistance.

The voltage of the lightbulb is given as 35.0 V.

The resistance of the lightbulb is given as 175 Ohm.

As the equation is given,

V= IR

where I is current, R is resistance and V is the voltage.

Now, I = V/R

As the value of Voltage and resistance of the lightbulb is given, we will put in the above equation, we get;

I = 35.0/ 175 A

I = 0.2 A.

Hence, the current of the lightbulb is 0.2 A.

Therefore, Option C is the correct answer.

To learn more about Current, refer to:

Explanation:

Answer:

The student used 24000 Joules of energy.

Explanation:

We can use the Energy Power equation to solve this example.

[tex]\sf E=Pt[/tex]

Where

[tex]\sf E[/tex] is the energy in Joules (J)

[tex]\sf P[/tex] is the power in Watts (W)

[tex]\sf t[/tex] is the time in seconds (s)

Numerical Evaluation

In this example we are given

[tex]\sf P=800\\t=30[/tex]

Substituting our given values into the equation yields

[tex]\sf E=800 \cdot 30[/tex]

[tex]\sf E=24000[/tex]

24000 Joules  

[tex]\Large\bold{SOLUTION}[/tex]

To calculate the energy used by the student in this scenario, we can use the formula:

[tex]\sf{Energy\: (in\: Joules) = Power\: (in\: Watts) \times Time\: (in\: seconds)}[/tex]

Given that the student uses an 800 W microwave for 30 seconds, we can plug in these values to the formula:

[tex]\sf Energy = 800\: W \times 30\: s = 24,000\: J[/tex]

Therefore, the student uses 24,000 Joules of energy in this scenario.

[tex]\rule{200pt}{5pt}[/tex]

Answer:

- 0.33 m/s

Explanation:

An illustration is shown above,

In this case, since the two objects move in opposite directions before collision, then move together, the formula to be used is,

m1u1 - m2u2 = (m1 + m2)v

Where,

m1 = mass of the first object

u1 = initial velocity of the first object

v1 = final velocity of the first object

m2 = mass of the second object

u2 = initial velocity of the second object

v2 = final velocity of the second object

Therefore,

(4.0 • 3.0) - (8.0 • 2.0) = (4.0 + 8.0)v

12 - 16 = 12v

-4 = 12v

Divide both sides by 12,

-4 / 12 = 12v / 12

-1 / 3 = v

v = -0.33 m/s

Please mark brainliest.

Thanks

The two gases that could be components of water are indeed hydrogen and oxygen.

Evidence to support this claim:

1. The chemical formula for water is H2O, which means that it is composed of two hydrogen atoms and one oxygen atom.

2. The table of elements shows that hydrogen (H) and oxygen (O) are both elements that exist in nature.

3. The atomic mass of hydrogen (1.008) and oxygen (15.999) matches the molecular mass of water (18.015).

4. Water is produced when hydrogen gas (H2) is burned in the presence of oxygen gas (O2), according to the following equation: 2H2 + O2 → 2H2O.

Overall, the evidence supports the conclusion that hydrogen and oxygen are the two gases that could be components of water.

To know more about water please refer: https://brainly.com/question/31037355

#SPJ1

Thank you for reaching out to me with your question. From what I understand, you are curious about the importance of an assignment or exam that is worth 20% of your grade.

To put it simply, any assignment or exam that is worth a certain percentage of your grade is an indicator of how much weight that particular task carries in determining your overall grade for the course. In other words, if you were to score poorly on an assignment that is worth 20% of your grade, it could significantly impact your final grade.
It is important to note that each assignment or exam may be worth a different percentage, and it is up to the instructor to determine the weight of each task. Generally, assignments and exams that are worth a higher percentage of your grade carry more weight and have a greater impact on your final grade.
Therefore, it is crucial to take each assignment or exam seriously and give it your best effort, especially those that carry a higher percentage of your grade. It is also important to keep track of your grades throughout the semester and identify any areas that may need improvement, so you can work towards improving your overall grade.
I hope this explanation helps clarify the importance of an assignment or exam that is worth a certain percentage of your grade. Please let me know if you have any further questions or concerns.

for more such questions on importance

https://brainly.com/question/628845

#SPJ11

Mechanical energy to heat energy is collision,force x distance is work done,rubbing energy friction, stewardship is using energy wisely and nuclear energy can cause heat pollution.

For more information on energy kindly visit to

https://brainly.com/question/10770247

#SPJ1

The final velocity of the cylinder is 1.22 m/s when it reaches the bottom of the ramp.

To solve this problem, we need to use conservation of energy and rotational kinematics.

Calculate the gravitational potential energy (GPE) of the cylinder at the top of the ramp:

GPE = mgh = (2.9 kg)(9.81)(0.75 m) = 21.39 J

Calculate the final kinetic energy (KE) of the cylinder when it reaches the bottom of the ramp:

[tex]KE = 1/2 mv^2 + 1/2 Iω^2[/tex]

where v is the linear velocity, I is the moment of inertia, and ω is the angular velocity.

Since the cylinder rolls without slipping, we know that v = ωr, where r is the radius of the cylinder.

[tex]KE = 1/2 mv^2 + 1/4 mv^2 = 3/4 mv^2 = 3/8 mgh[/tex]

Substituting the values we have:

KE = 3/8 (2.9 kg)(9.81)(0.75 m) = 63.56 J

Finally, we can use conservation of energy to find the final velocity of the cylinder:

GPE = KE

[tex]mgh = 3/8 mgh + 1/2 mv^2 + 1/2 Iω^2[/tex]

Solving for velocity:

[tex]v = \sqrt (2gh/5) = \sqrt(29.81 m/s^20.75 m/5) = 1.22 m/s[/tex]

learn more about conservation of energy here:

https://brainly.com/question/2137260

#SPJ1

the complete question is:

At the top of a ramp, a 2.9 kg solid cylinder (radius = 0.20 m, length = 0.70 m) is released from rest and allowed to roll without slipping. The ramp measures 0.75 m in height and 5.0 m in length. calculate the final velocity when it reaches the bottom of the ramp

Answer:

The student use 2400 Joules

Explanation:

From the formula E = pt

p = 800W

t = 3 seconds

=> E = 800*3 = 2400J

Answer:

Explanation:

We can solve this problem using kinematic equations. We know that the initial velocity of the ball is 55 m/s at an angle of 30° to the horizontal. We can break this velocity into its horizontal and vertical components:

vx = v0 cos θ = 55 cos 30° = 47.6 m/s

vy = v0 sin θ = 55 sin 30° = 27.5 m/s

We can now use the vertical motion equation to find the time it takes for the ball to reach its maximum height:

Δy = vy t + 0.5 a t^2

At the maximum height, the vertical velocity of the ball is 0, so we have:

0 = vy + a t_max

Solving for t_max, we get:

t_max = -vy / a = -27.5 / (-9.8) = 2.81 s

The ball will take twice this time to reach the fence, since it needs to come back down to the ground:

t_total = 2 t_max = 5.62 s

The horizontal distance the ball travels during this time is:

Δx = vx t_total = 47.6 × 5.62 = 267.7 m

Since this distance is greater than the distance to the fence (120 m), the ball will reach the fence if it leaves the bat traveling upward at an angle of 30° to the horizontal.

Answer:

Explanation:

The formula relating the speed of sound, frequency, and wavelength is:

speed = frequency x wavelength

Rearranging this formula to solve for frequency:

frequency = speed / wavelength

Substituting the given values:

frequency = 342 m/s / 1.8 m

frequency = 190 Hz

Therefore, the frequency of the sound wave is 190 Hz.

Real, inverted, and same size are the features of the image. when A concave mirror with a curvature of 8 is displayed on a ruler with a range of 0 to 14 cm.

The mirror formula may be used to calculate the image distance for an item located 4 cm from a 1.5 cm focal length mirror.

1/f = 1/u+1/v

f is the focal length

u is the object distance

v is the image distance

Keep in mind that the concave mirror's image distance and focal length are both positive.

Given:

u = 4cm

f = 1.5cm

1/v = 1/1.5-1/4

1/v = 0.67-0.25

1/v = 0.42

v = 1/0.42

v = 2.38cm

The picture is Genuine and INVERTED since the image distance value is positive.

We shall find its magnification and see if it is magnified or lessened. It is amplified if the magnification is larger than 1, and it is decreased if it is less.

Magnification = v/u

Magnification = 2.38/4

Magnification = 0.595 or. 0.6

The picture is reduced in size since the magnification is less than one (SMALLER).

Learn more about Inverted here:

https://brainly.com/question/16150120

#SPJ1

The truck's acceleration is 3.0m/s² and the momentum of the truck is  144000 kg m/s.

It is the rate at which the speed and direction of a moving object vary over time.

We can use the following equation to calculate the acceleration of the truck:

a = (v - u) / t

where

a = acceleration

v = final velocity = 18.0 m/s

u = initial velocity = 0 m/s (the truck starts from rest)

t = time taken = 6.00 s

Substituting the values, we get:

a = (18.0 m/s - 0 m/s) / 6.00 s

a = 3.00 m/s²

Therefore, the acceleration of the truck is 3.00 m/s².

We can use the following equation to calculate the momentum of the truck:

p = m * v

where

p = momentum

m = mass of the truck = 8000.0 kg

v = final velocity = 18.0 m/s

Substituting the values, we get:

p = 8000.0 kg * 18.0 m/s

p = 144000 kg m/s

Therefore, the momentum of the truck after it has reached its final velocity is 144000 kg m/s.

Learn more about velocity here:

https://brainly.com/question/17127206

#SPJ9

Answer:

We can use the formula:

q = mcΔT

where q is the heat transferred, m is the mass, c is the specific heat capacity, and ΔT is the change in temperature.

The heat transferred from the gold bar to the water is equal to the heat transferred from the water to the gold bar, since they reach thermal equilibrium. Therefore:

q_gold = q_water

We can solve for the temperature change of the gold bar:

q_gold = mcΔT_gold

q_water = mcΔT_water

Since the heat transferred is equal:

mcΔT_gold = mcΔT_water

Rearranging and solving for ΔT_gold:

ΔT_gold = ΔT_water(m_water/m_gold)

ΔT_water is the temperature change of the water, which is 17°C. m_water is 0.220 kg, and m_gold is 3 kg. c_gold is given as 129 J/kg K.

ΔT_gold = 17°C(0.220 kg/3 kg)(1/129 J/kg K) = 0.025°C

Therefore, the temperature change of the gold bar is 0.025°C when it is placed into 0.220 kg of water and thermal equilibrium is reached.

Answer:

To solve this problem, we can use the formula:

d = (v^2)/(2μg)

d = distance traveled

v = speed of the car

μ = coefficient of kinetic friction

g = acceleration due to gravity

First, let's calculate the distance traveled when the car is traveling at 23 m/s:

d = (23^2)/(2*0.7*9.81) ≈ 67.97 meters

Now, let's calculate the distance traveled when the car is going twice as fast (46 m/s):

d = (46^2)/(2*0.7*9.81) ≈ 271.88 meters

Therefore, the car would travel approximately 271.88 meters if it were going twice as fast.

Answer:

Explanation:

To use Gauss's Law, we need to choose a Gaussian surface that encloses the point of interest and has symmetry such that the electric field is constant over the surface. For all points in this problem, we can choose a cylinder as our Gaussian surface with its axis perpendicular to the sheets.

Let's assume that the cylinders are tall enough such that the electric field at the top and bottom faces of the cylinder is negligible. The electric flux through the curved part of the cylinder is constant and equal to Φ_E = E*A, where A is the surface area of the curved part of the cylinder.

Using Gauss's Law, Φ_E = Q_in / ε0, where Q_in is the net charge enclosed by the Gaussian surface and ε0 is the permittivity of free space.

A: The Gaussian surface is a cylinder with radius r = 5.00 cm and height h = the distance between the sheets (20.0 cm). The net charge enclosed is Q_in = σ1 * A_top + σ2 * A_bottom, where A_top and A_bottom are the areas of the top and bottom faces of the cylinder, respectively. Since the electric field is perpendicular to the faces, the flux through them is zero. So, Q_in = (σ1 - σ2) * A, where A is the surface area of the curved part of the cylinder. Thus,

Φ_E = E * A = Q_in / ε0

E = (σ1 - σ2) / (ε0 * r) = (-7.30 μC/m^2 - 5.00 μC/m^2) / (8.85 x 10^-12 C^2/Nm^2 * 0.0500 m) = -2.31 x 10^5 N/C

The magnitude of the electric field at point A is 2.31 x 10^5 N/C.

B: The electric field points from higher potential to lower potential. Since the left-hand sheet has a negative charge density and the right-hand sheet has a positive charge density, the potential decreases from left to right. Thus, the electric field at point A points from left to right.

The direction of the electric field at point A is RIGHT.

C: The Gaussian surface is a cylinder with radius r = 1.25 cm and height h = the thickness of the right-hand sheet (10.0 cm). The net charge enclosed is Q_in = σ4 * A, where A is the surface area of the curved part of the cylinder. Thus,

Φ_E = E * A = Q_in / ε0

E = σ4 / (ε0 * r) = 4.00 μC/m^2 / (8.85 x 10^-12 C^2/Nm^2 * 0.0125 m) = 3.77 x 10^7 N/C

The magnitude of the electric field at point B is 3.77 x 10^7 N/C.

D: The electric field points from higher potential to lower potential. Since the right-hand sheet has a positive charge density, the potential decreases from the right-hand sheet to the left. Thus, the electric field at point B points from right to left.

The direction of the electric field at point B is LEFT.

E:

Since point C is in the middle of the right-hand sheet, the electric field due to this sheet alone cancels out due to symmetry. Thus, the only electric field present is due to the left-hand sheet. The Gaussian surface is a cylinder with radius r = the radius of the sheet (10.0 cm) and height h = the thickness of the sheet (10.0 cm). The net charge enclosed is Q

The net charge enclosed within this Gaussian surface is:

Q = σ1 × (2πrh)

where h is the thickness of the left-hand sheet, r is the distance from the left-hand sheet to point C, and σ1 is the surface charge density of the left-hand sheet. Plugging in the given values, we get:

Q = (-7.30 × 10^-6 C/m^2) × (2π × 0.1 m × 0.1 m) = -4.60 × 10^-8 C

Using Gauss's law, we can find the electric field at point C:

E × (2πrh) = Q/ε0

where ε0 is the permittivity of free space. Solving for E, we get:

E = Q / (2πε0rh)

Plugging in the values, we get:

E = (-4.60 × 10^-8 C) / (2π × 8.85 × 10^-12 C^2/(N·m^2) × 0.1 m × 0.1 m) = -1.64 × 10^5 N/C

Therefore, the magnitude of the electric field at point C is 1.64 × 10^5 N/C.

To find the electric field at point C, we need to consider both sheets since point C is equidistant from both sheets. Thus, we can use Gauss's law to find the total electric field due to both sheets.

The net charge enclosed by a cylindrical Gaussian surface of radius r = 1.25 cm and height h = 20.0 cm is given by:

qenc = σ2 * (2πrh) + σ4 * (2πrh) = (σ2 + σ4) * (2πrh)

where σ2 is the charge density on the inner surface of the right-hand sheet, σ4 is the charge density on the outer surface of the left-hand sheet, and h is the distance between the two sheets.

Substituting the given values, we get:

qenc = (5.00 μC/m^2 + 4.00 μC/m^2) * (2π * 1.25 cm * 20.0 cm) = 628.32 nC

Using Gauss's law, we have:

E * 2πrh = qenc/ε0

where ε0 is the permittivity of free space.

Solving for E, we get:

E = qenc / (2πrhε0) = 2.22 × 10^4 N/C

Therefore, the magnitude of the electric field at point C is 2.22 × 10^4 N/C.

F:

The direction of the electric field at point C is perpendicular to the surface of the sheet, pointing away from the positive charge density and towards the negative charge density. Since the positive charge density is on the outer surface of the left-hand sheet and the negative charge density is on the inner surface of the right-hand sheet, the direction of the electric field at point C is from left to right. Therefore, the direction of the electric field at point C is RIGHT.

The net flux of an electric field in a closed surface is directly proportionate to the charge contained, according to Gauss' equation.

To use Gauss's Law, we need to choose a Gaussian surface that encloses the point of interest and has symmetry such that the electric field is constant over the surface. For all points in this problem, we can choose a cylinder as our Gaussian surface with its axis perpendicular to the sheets.

Let's assume that the cylinders are tall enough such that the electric field at the top and bottom faces of the cylinder is negligible. The electric flux through the curved part of the cylinder is constant and equal to Φ_E = E*A, where A is the surface area of the curved part of the cylinder.

Using Gauss's Law, Φ_E = Q_in / ε0, where Q_in is the net charge enclosed by the Gaussian surface and ε0 is the permittivity of free space.

A: The Gaussian surface is a cylinder with radius r = 5.00 cm and height h = the distance between the sheets (20.0 cm). The net charge enclosed is Q_in = σ1 * A_top + σ2 * A_bottom, where A_top and A_bottom are the areas of the top and bottom faces of the cylinder, respectively.

Φ_E = E * A = Q_in / ε0

E = (σ1 - σ2) / (ε0 * r) = (-7.30 μC/m^2 - 5.00 μC/m^2) / (8.85 x 10^-12 C^2/Nm^2 * 0.0500 m) = -2.31 x 10^5 N/C

The magnitude of the electric field at point A is 2.31 x 10^5 N/C.

B: The electric field points from higher potential to lower potential. Since the left-hand sheet has a negative charge density and the right-hand sheet has a positive charge density, the potential decreases from left to right. Thus, the electric field at point A points from left to right.

The direction of the electric field at point A is RIGHT.

C: The Gaussian surface is a cylinder with radius r = 1.25 cm and height h = the thickness of the right-hand sheet (10.0 cm). The net charge enclosed is Q_in = σ4 * A, where A is the surface area of the curved part of the cylinder. Thus,

Φ_E = E * A = Q_in / ε0

E = σ4 / (ε0 * r) = 4.00 μC/m^2 / (8.85 x 10^-12 C^2/Nm^2 * 0.0125 m) = 3.77 x 10^7 N/C

The magnitude of the electric field at point B is 3.77 x 10^7 N/C.

D: The electric field points from higher potential to lower potential. Since the right-hand sheet has a positive charge density, the potential decreases from the right-hand sheet to the left. Thus, the electric field at point B points from right to left.

The direction of the electric field at point B is LEFT.

E:Since point C is in the middle of the right-hand sheet, the electric field due to this sheet alone cancels out due to symmetry. Thus, the only electric field present is due to the left-hand sheet. The Gaussian surface is a cylinder with radius r = the radius of the sheet (10.0 cm) and height h = the thickness of the sheet (10.0 cm). The net charge enclosed is Q

The net charge enclosed within this Gaussian surface is:

Q = σ1 × (2πrh)

where h is the thickness of the left-hand sheet, r is the distance from the left-hand sheet to point C, and σ1 is the surface charge density of the left-hand sheet. Plugging in the given values, we get:

Q = (-7.30 × 10^-6 C/m^2) × (2π × 0.1 m × 0.1 m) = -4.60 × 10^-8 C

Using Gauss's law, we can find the electric field at point C:

E × (2πrh) = Q/ε0

where ε0 is the permittivity of free space. Solving for E, we get:

E = Q / (2πε0rh)

Plugging in the values, we get:

E = (-4.60 × 10^-8 C) / (2π × 8.85 × 10^-12 C^2/(N·m^2) × 0.1 m × 0.1 m) = -1.64 × 10^5 N/C

Therefore, the magnitude of the electric field at point C is 1.64 × 10^5 N/C.

To find the electric field at point C, we need to consider both sheets since point C is equidistant from both sheets. Thus, we can use Gauss's law to find the total electric field due to both sheets.

The net charge enclosed by a cylindrical Gaussian surface of radius r = 1.25 cm and height h = 20.0 cm is given by:

qenc = σ2 * (2πrh) + σ4 * (2πrh) = (σ2 + σ4) * (2πrh)

where σ2 is the charge density on the inner surface of the right-hand sheet, σ4 is the charge density on the outer surface of the left-hand sheet, and h is the distance between the two sheets.

Substituting the given values, we get:

qenc = (5.00 μC/m^2 + 4.00 μC/m^2) * (2π * 1.25 cm * 20.0 cm) = 628.32 nC

Using Gauss's law, we have:

E * 2πrh = qenc/ε0

where ε0 is the permittivity of free space.

Solving for E, we get:

E = qenc / (2πrhε0) = 2.22 × 10^4 N/C

Therefore, the magnitude of the electric field at point C is 2.22 × 10^4 N/C.

F:The direction of the electric field at point C is perpendicular to the surface of the sheet, pointing away from the positive charge density and towards the negative charge density. Since the positive charge density is on the outer surface of the left-hand sheet and the negative charge density is on the inner surface of the right-hand sheet, the direction of the electric field at point C is from left to right. Therefore, the direction of the electric field at point C is RIGHT.

Learn more about  Gauss's law

https://brainly.com/question/14767569

#SPJ1

The hammer's centripetal acceleration is therefore 100.59 m/s².

An object has positive acceleration when it is going faster than it was previously. Positive acceleration was demonstrated by the moving car in the first scenario. Positive forward motion is being made by the car.

Hammer mass, m, is 6.55 kg. chain length, including the length of the arms, r = 1.3 m, Hammer's angular velocity is given by the formula: = 1.4 rev/s = 8.79646 rad/s (1 rev = 6.28 rad).

The formula a = V2/r, where V is the transverse velocity of the hammer, yields the centripetal acceleration.

V = r, hence

As a result, a = r²

A = 1.3 x 8.796462, or 100.59 m/s², is obtained by substituting the supplied numbers in the equation above.

The hammer's centripetal acceleration is therefore 100.59 m/s².

To know more about Acceleration visit:

brainly.com/question/30499732

#SPJ1

Answer:

power plant

collision

Battery

Burning wood

speaker

Beating drum

The voltage of the battery would be 20 volts. Option I.

According to Ohm's law, the voltage (V) across a resistor is equal to the current (I) flowing through it multiplied by its resistance (R). Mathematically,

V = I × R

In this case, the current (I) flowing through the resistor is given as 10 A and the resistance (R) of the resistor is given as 2 ohms. Substituting these values into the above formula, we get:

V = 10 A × 2 ohms = 20 volts

Therefore, the voltage of the battery is 20 volts.

More on voltage can be found here: https://brainly.com/question/13521443

#SPJ1

Answer:

Pulse transfers a single disturbance, while wave is a continuous disturbance that transfers energy.

If you found this response helpful, please consider marking it as brainliest.

It takes 0.1311 seconds to hear the echo of the stone.

First we need to determine the time it takes for the sound wave to travel from the stone to the bottom of the mine shaft and back up to our ears.

Let's start by finding the time it takes for the sound wave to reach the bottom of the mine shaft. We can use the formula:

time = distance / speed

The distance is the depth of the mine shaft, which is 15 meters. The speed of sound is 343 m/s, as given in the problem. Therefore, the time it takes for the sound wave to reach the bottom of the mine shaft is:

time = 15 m / 343 m/s

time = 0.0437 s

Now, we need to find the time it takes for the sound wave to travel back up to our ears. Since the sound wave travels at the same speed, 343 m/s, the distance it needs to cover is twice the depth of the mine shaft, or 30 meters. Therefore, the time it takes for the sound wave to travel back up to our ears is:

time = 30 m / 343 m/s

time = 0.0874 s

Finally, to find the total time it takes to hear the echo, we add the time it takes for the sound wave to reach the bottom of the mine shaft to the time it takes to travel back up to our ears:

total time = 0.0437 s + 0.0874 s

total time = 0.1311 s

Therefore, it takes 0.1311 seconds to hear the echo of the stone.

Learn more about sound wave here : brainly.com/question/13105733

#SPJ1

Therefore, the potential difference of the circuit is 30 volts.

The external effort required to move a charge from one position to another in an electric field is known as an electric potential difference, or voltage. A test charge that has an electric potential differential of +1 will experience a shift in potential energy.

To calculate the potential difference (V) of the circuit, we can use Ohm's Law, which states that V = IR, where I is the current flowing through the circuit and R is the resistance of the circuit.

In this case, the current (I) is given as 0.5 A and the resistance (R) is given as 60 Ω. Therefore, we can substitute these values into Ohm's Law to find the potential difference:

V = IR

V = 0.5 A × 60 Ω

V = 30 volts

To know more about potential difference visit:-

brainly.com/question/12198573

#SPJ9