The resistivity of the wire material can be calculated using Ohm's Law, which states that V=IR, or voltage = current multiplied by resistance. Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8} \Omega m[/tex].
Resistivity of wire is given as ρ=RA/L where R is the resistance of wire, A is the cross-sectional area of the wire, L is the length of the wire.
The formula to calculate the resistance of wire from Ohm's Law is given by R=V/I where V is the voltage, I is the current.
Substituting the given values: V = 12.0 V, I = 7.5 A.
Therefore, R=V/I=12.0 / 7.5 = 1.6 Ω
From the formula of resistivity:
[tex]\rho=\dfrac{RA}{L}\\R=\dfrac{ρL}{A}[/tex]
Substituting the given values: R = 1.6 Ω, L = 11.0 m and calculating the area:
[tex]A = (1.8 \times 10^{-3} m) (0.11 \times 10^{-3} m)\\ = 0.198 \times 10^{-6} m²[/tex]
Therefore,
[tex]\rho = RA/L\\= \dfrac{R \times A}{ L}\\= \frac{1.6 \times 0.198 \times 10^{-6}}{ 11.0}\\ = 2.87 \times 10^{-8 } \Omega m[/tex]
Therefore, the resistivity of the wire material is [tex]2.87 \times 10^{-8 } \Omega m[/tex].
For more details on resistivity, click on the below link:
https://brainly.com/question/30799966
#SPJ11
a value of mass is given as 14.6 g to 15.2 g. a value of volume is given as 2.4 to 2.8 m3. state the density using reasonable outer limits.
The density using reasonable outer limits is the density of an object can be determined by dividing its mass (measured in grams, g) by its volume (measured in cubic metres, m3). To calculate the density using the given values of mass and volume, we can use the following formula: Density = Mass/Volume.
Therefore, the density of the given object can be calculated using the outer limits of mass and volume, which are 14.6 g to 15.2 g and 2.4 m3 to 2.8 m3, respectively. The calculated density of the given object is in the range of 5.75 g/m3 to 5.45 g/m3.
To calculate the density, the mass and volume of the object must be known. Mass is a measure of how much matter an object has, and is calculated in grams (g). Volume, on the other hand, is a measure of the amount of space an object takes up, and is calculated in cubic metres (m3).
When these two values are known, the density can be calculated using the formula: Density = Mass/Volume. In this case, the given values of mass and volume are 14.6 g to 15.2 g and 2.4 m3 to 2.8 m3, respectively. By substituting these values into the formula, the density of the object can be calculated as follows:
Density = Mass/Volume
Density = 14.6 g/2.4 m3 = 5.75 g/m3
Density = 15.2 g/2.8 m3 = 5.45 g/m3
Therefore, the density of the given object is in the range of 5.75 g/m3 to 5.45 g/m3.
To know more about density refer here:
https://brainly.com/question/15164682#
#SPJ11
logs sometimes float vertically in a lake because one end has become water-logged and denser than the other. what is the average density of a uniform-diameter log that floats with 20.0% of its length above water?
Uneven-diameter logs that float with 20.0% of their length above water have an average density of 0.8g/cm3. The density is the proportion of weight to capacity.
An item it's far less compact that liquid may be supported up liquid water, and hence it floats. More dense objects can sink when submerged in water. Less dense logs float whereas more thick logs sink. A body can change its condition of rest or motion by the application of force
Instead of obliquely reading from either the side, read the scale stick straight from of the end of both the log. → The diameter of a log is only ever calculated within the bark. Employ a log measuring rod to determine the log's small end's "diameter from within bark," also known as "d.i.b."
To know more about force click here
brainly.com/question/29044739
#SPJ4
We were just introduced to electricity in physics and I have some questions:
1. Since electrons can be transferred from our hair to the balloon, can electrons also be transferred from the balloon to our hair? (Do questions always say whether an object is positive or negative charge)
2. Do electrons stay in place since balloons are rubber insulators?
3. What point do neutrons serve? Are they just there?
4. Are objects in constant exchange of energy with one another? Whenever they come in contact they exchange electrons until equal?
1 - Since electrοns can be transferred frοm οur hair tο the ballοοn , electrοns cannοt be transferred frοm ballοοn tο οur hair because. This is an illustratiοn οf charging by cοnductiοn.
2 - Since the rubber οn the ballοοn is significantly less cοnductive than the hair, electrοns will nοt easily escape the ballοοn because οf this.
3 - Neutrοns are electrically neutral , neutrοns dοesn't participate in this prοcess.
What is charging by cοnductiοn?A charged οbject must cοme intο cοntact with a neutral οbject tο cοnduct electricity. As a result, when twο charged cοnductοrs cοme intο cοntact, the charge is split between the twο cοnductοrs, charging the uncharged cοnductοr.
When twο neutral οbjects are rubbed against οne anοther, electrοns are transferred. The οbject that has a strοnger affinity fοr electrοns will take electrοns frοm the οther οbject, and the twο becοme charged in οppοsitiοn. In this instance, the electrοns frοm the hair are taken up by the ballοοn , which nοw has an excess οf electrοns and a negative charge cοmpared tο the hair's current electrοn shοrtage and pοsitive charge.
2- Since the rubber οn the ballοοn is significantly less cοnductive than the hair, electrοns will nοt easily escape the ballοοn because οf this.
3- Neutrοns are electrically neutral , neutrοns dοesn't participate in this prοcess.
4-Insulating materials may becοme electrically charged when they cοme intο cοntact with οne anοther. Negatively charged electrοns can "rub οff" οne material and "rub οn" tο anοther. After bοth things have the same quantity οf οppοsite charges, the substance that gets electrοns becοmes negatively charged, and the material that lοses electrοns becοmes pοsitively charged.
To know more about charging by conduction , visit;
brainly.com/question/10254645
#SPJ1
a brick is falling from the roof of a three-story building. how many force vectors would be shown on a free-body diagram? name them
A brick is falling from the roof of three story building then free-body diagram would show only one force vector, which is the force of gravity acting on the brick.
A free-body diagram is used to graphically represent the forces acting on an object. It shows all of the forces acting on an object and can be used to analyze the motion of an object.
A free-body diagram for a falling brick would include two force vectors: Gravity or Weight.
If we consider only the brick and neglect air resistance, then there are two force vectors that would be shown on a free-body diagram of the brick:Force of gravity: The force of gravity, which pulls the brick downwards with a magnitude of its weight. This force is always present and directed downwards towards the center of the Earth. Normal Force: The normal force, which is the force exerted by the roof or any surface in contact with the brick that prevents it from falling through the surface. As the brick is falling, there is no contact force from the roof, so the normal force is zero.So, in this scenario, the free-body diagram would show only one force vector, which is the force of gravity acting on the brick.
To lean more about the 'force vectors':
https://brainly.com/question/30893090
#SPJ11
an n-type piece of silicon experiences an electric field equal to 0.1v/m. (a) calculate the velocity of electrons and holes in this material
In an n-type piece of silicon, the electric field causes the electrons to accelerate due to the attractive force between the negatively charged electrons and the positively charged electric field. This acceleration causes the electrons to reach a velocity of V = E/μ, where E is the electric field (0.1V/m) and μ is the mobility of electrons in silicon (1350 cm2/V⋅s). Therefore, the velocity of electrons in this material would be equal to 0.1V/m/1350cm2/V⋅s = 0.0741 cm/s.
The holes, on the other hand, experience a repulsive force due to the positive electric field. This causes the holes to decelerate, with a velocity of V = -E/μ. Therefore, the velocity of holes in this material would be equal to -0.1V/m/1350cm2/V⋅s = -0.0741 cm/s.
Know more about electric field here:
https://brainly.com/question/8971780
#SPJ11
pry on the power steering reservoir to adjust the tension of the power steering belt. true or false?
The statement "pry on the power steering reservoir to adjust the tension of the power steering belt" is: false.
The tension of the power steering belt is adjusted by adjusting the position of the power steering pump. There is a tension adjustment bolt on the power steering pump that is used to adjust the tension of the power steering belt. The adjustment bolt should be turned clockwise or counterclockwise to adjust the tension of the belt.
A belt tension gauge may be used to ensure that the belt is properly tensioned. A pry bar should not be used on the power steering reservoir to adjust the tension of the power steering belt. This could cause damage to the reservoir or other components of the power steering system. The reservoir should be inspected for damage or leaks, but it should not be used to adjust the tension of the belt.
In summary, the tension of the power steering belt should be adjusted by adjusting the position of the power steering pump, not by prying on the power steering reservoir.
To know more about tension refer here:
https://brainly.com/question/29869473#
#SPJ11
An ice skater is spinning about a vertical axis with arms fully extended. If the arms are pulled in closer to the body, in which of the following ways are the angular momentum and kinetic energy of the skater affected?
Angular Momentum Kinetic Energy
(A) Increases Increases
(B) Increases Remains Constant
(C) Remains Constant Increases
(D) Remains Constant Remains Constant
(E) Decreases Remains Constant
An ice skater is spinning about a vertical axis with arms fully extended. If the arms are pulled closer to the body, the angular momentum of the skater will remain constant while the kinetic energy of the skater increases. The correct option is C.
The angular momentum of the skater is given by
[tex]L = I\omega[/tex],
where I is the moment of inertia of the skater and ω is the angular velocity.
When the skater pulls their arms in, their moment of inertia decreases due to the decreased distance between their body and the axis of rotation.
According to the conservation of angular momentum, the product of the moment of inertia and angular velocity must remain constant. Therefore, if the moment of inertia decreases, the angular velocity must increase to keep the angular momentum constant.
The kinetic energy of the skater is given by
[tex]K = (1/2)I\omega^2[/tex]
As the moment of inertia decreases and the angular velocity increases, the kinetic energy of the skater also increases because it is proportional to the square of the angular velocity.
Therefore, the correct answer is: (C) Remains Constant Increases. The angular momentum remains constant, while the kinetic energy increases due to the increased angular velocity.
Learn more about angular momentum:
https://brainly.com/question/4126751
#SPJ11
find the net force on a 30.0 nc charge located at the origin by two other charges. one is -50.0 nc located at (-5.0 m, 2.0 m) and 40.0 nc located at (3.0 m, 1.0 m).
The net force on a 30.0 nc charge located at the origin by two other charges is the vector sum of the forces exerted by the two other charges. The force exerted by the first charge, -50.0 nC located at (-5.0 m, 2.0 m), is given by:
F1 = (k*q1*q2)/r2, where
k = 8.99 x 109 N m2/C2q1 = -50.0 ncq2 = 30.0 ncr = square root of (5.02 + 2.02) = 5.385Therefore,
F1 = (8.99 x 109 N m2/C2)*(-50.0 nc)*(30.0 nc)/(5.3852) = 2.38 x 10-2 N
Similarly, the force exerted by the second charge, 40.0 nc located at (3.0 m, 1.0 m), is given by:
F2 = (k*q1*q2)/r2, where
k = 8.99 x 109 N m2/C2q1 = 40.0 ncq2 = 30.0 ncr = square root of (3.02 + 1.02) = 3.162Therefore,
F2 = (8.99 x 109 N m2/C2)*(40.0 nc)*(30.0 nc)/(3.1622) = 4.58 x 10-2 N
The net force is the vector sum of F1 and F2 and can be calculated as follows:
F net = F1 + F2 = 2.38 x 10-2 N + 4.58 x 10-2 N = 7.00 x 10-2 N
Therefore, the net force on a 30.0 nc charge located at the origin by two other charges is 7.00 x 10-2 N.
To know more about Force refer here:
https://brainly.com/question/13191643#
#SPJ11
when rotating the platform, the hanging mass should be removed from the platform. question 2 options: true false
The given statement, while the platform is rotating, the hanging mass remains attached to the test mass and is not removed from the platform is true, if the purpose of the experiment or test is to determine the effect of the hanging mass on the rotation or stability of the platform.
In this case, the hanging mass must remain attached to the test mass during the rotation to observe the behavior of the system under the specified conditions. If the purpose of the experiment or test is to study the effect of the hanging mass on the platform's rotation or stability, the hanging mass must remain attached to the test mass during the rotation. This is because the presence of the hanging mass affects the overall weight and center of gravity of the system. Removing the hanging mass would alter the system's behavior and prevent accurate observations of the phenomenon under investigation. Therefore, if the experiment requires the hanging mass to be present, it must remain attached to the test mass while the platform is rotating.
To know more about platform, here
brainly.com/question/22850608
#SPJ4
--The complete question is, While the platform is rotating, the hanging mass remains attached to the test mass and is not removed from the platform. State true/false.--
if the rate of internal energy dissipation in a battery is 1.0 watt, and the current produced by the battery is 0.50 amps, what is the internal resistance of the battery?
If the rate of internal energy dissipation in a battery is 1.0 watt, and the current produced by the battery is 0.50 amps, the internal resistance of the battery can be calculated using Ohm's law. Ohm's law states that the current through a conductor between two points is directly proportional to the voltage across the two points. The proportionality constant is called the resistance of the conductor, which is expressed mathematically as V = IR, where V is the voltage, I is the current, and R is the resistance.
The power dissipated by the internal resistance of a battery is given by P = I2R, where P is the power, I is the current, and R is the internal resistance. The rate of internal energy dissipation in the battery is given as 1.0 watt, and the current produced by the battery is given as 0.50 amps.
Using Ohm's law, we can calculate the voltage across the battery as V = IR = 0.50 x R. Therefore, the power dissipated by the internal resistance of the battery is P = I2R = (0.50)2 x R = 0.25R.
Equating the power dissipated by the internal resistance of the battery to the rate of internal energy dissipation, we get:
0.25R = 1.0
Solving for R, we get:
R = 1.0/0.25 = 4 ohms.
Therefore, the internal resistance of the battery is 4 ohms.
Internal energy dissipation is the energy that is lost due to friction or resistance in a system. In the case of a battery, internal energy dissipation refers to the energy that is lost due to the internal resistance of the battery. The internal resistance of a battery is a measure of how much energy is lost due to the resistance of the battery's internal components. The higher the internal resistance of the battery, the more energy is lost as heat, which reduces the battery's efficiency.
To know more about Internal energy dissipation refer here:
https://brainly.com/question/15331125#
#SPJ11
an asteroid orbits the sun in a highly elliptical orbit. as the asteroid gets closer to the sun, how are the total mechanical energy and gravitational potential energy of the asteroid-sun system changing, if at all?
The total mechanical energy and gravitational potential energy of the asteroid-sun system will change.
Asteroid-sun systemAs the asteroid gets closer to the sun in its highly elliptical orbit, both the total mechanical energy and gravitational potential energy of the asteroid-sun system will change.
The total mechanical energy of the asteroid-sun system is the sum of its kinetic energy and gravitational potential energy. As the asteroid moves closer to the sun, its kinetic energy will increase due to the increase in speed, but its gravitational potential energy will decrease due to the decrease in distance from the sun. Therefore, the total mechanical energy of the asteroid-sun system will remain constant, according to the law of conservation of energy.
However, if the asteroid encounters any gravitational forces or other external forces, such as a collision with another object or a thrust from a spacecraft, its mechanical energy can change.
More on asteroids can be found here: https://brainly.com/question/19161842
#SPJ1
an electric eel can generate a 278-v, 0.8-a shock for stunning its prey. what is the eel's power output?
The electric eel's power output is 222.4 Watts
Given voltage (V) = 278 V
Current (I) = 0.8 A
To find the electric eel's power output, we have to use the formula
P = IV,
Where P is the power output, I is current, and V is the voltage.
So, we can calculate the electric eel's power output as follows:
Power Output (P) = IVP
⇒278 × 0.8
Power Output (P) = 222.4 Watts
Hence, The power output of the electric eel is 222.4 Watts.
To know more about "power output": https://brainly.com/question/866077
#SPJ11
a ball of mass is dropped. what is the formula for the impulse exerted on the ball from the instant it is dropped to an arbitrary time later?
The formula for the impulse exerted on the ball from the instant it is dropped to an arbitrary time later is:
Impulse = (Final momentum - Initial momentum)
What is impulse?Impulse is a vector quantity having both magnitude and direction, whereas momentum is a vector quantity, but the impulse is not equal to momentum. The impulse is the change in momentum.
If a ball of mass m is dropped from rest, then its initial momentum is zero.
The final momentum of the ball after falling for time t is:
Final momentum = mv
Where v is the velocity of the ball after falling for time t.
Therefore, the impulse exerted on the ball from the instant it is dropped to an arbitrary time later is:
Impulse = (mv - 0) = mv
To know more about impulse:
https://brainly.com/question/14073258
#SPJ11
if you hold a 1.85 kg k g package by a light vertical string, what will be the tension in this string when the elevator accelerates as in the previous part?
The tension in the string of a 1.85 kg package held by a light vertical string will depend on the acceleration of the elevator. When the elevator accelerates, the force of acceleration on the package will be equal and opposite to the tension in the string, causing the tension to increase.
The equation for tension in a string is:
Tension = Mass x Acceleration
Therefore, in this case, the tension in the string is equal to 1.85 kg x Acceleration.
If we assume that the acceleration of the elevator is a constant rate, then the tension in the string can be calculated by multiplying the mass of the package by the acceleration of the elevator.
To sum up, the tension in the string of a 1.85 kg package held by a light vertical string will depend on the acceleration of the elevator. If the acceleration of the elevator is a constant rate, then the tension in the string can be calculated by multiplying the mass of the package by the acceleration of the elevator.
For more such questions on Tension.
https://brainly.com/question/13397436#
#SPJ11
how to find the minimum thickness of a film such that reflected light undergo constructive interference
The minimum thickness of the film for constructive interference of reflected light would be t = 3*600/(2*1.4) = 850 nm.
The minimum thickness of a film required for constructive interference of reflected light can be calculated using the formula t = m*λ/(2*n),
where t is the minimum thickness of the film, m is the order of interference, λ is the wavelength of the light, and n is the index of refraction of the film.
For example, if the order of interference is 3, the wavelength of the light is 600 nm, and the index of refraction is 1.4,
the minimum thickness of the film for constructive interference of reflected light would be t = 3*600/(2*1.4) = 850 nm.
Constructive interference of reflected light occurs when the phase difference between the two waves is equal to an integral multiple of 2π.
This can be determined using the formula Δφ = (2π*m)/(λ*n), where Δφ is the phase difference, m is the order of interference, λ is the wavelength of the light, and n is the index of refraction of the film.
To achieve constructive interference, the minimum thickness of the film can be determined by ensuring that the phase difference is equal to an integral multiple of 2π.
The minimum thickness of a film required for constructive interference of reflected light can be calculated using the formula t = m*λ/(2*n),
where t is the minimum thickness of the film, m is the order of interference, λ is the wavelength of the light, and n is the index of refraction of the film.
Constructive interference can be achieved by ensuring that the phase difference between the two waves is equal to an integral multiple of 2π.
to know more about light refer here:
https://brainly.com/question/15200315#
#SPJ11
a system releases 690 kj of heat and does 110 kj of work on the surroundings. part a what is the change in internal energy of the system?
A system releases 690 kj of heat and does 110 kj of work on the surroundings then part a what i the change in internal energy of the system -800 kJ.
The change in internal energy of the system can be calculated using the formula
ΔU = Q - W,
where ΔU is the change in internal energy, Q is the heat exchanged, and W is the work done.
In this case, the system releases 690 kJ of heat (Q = -690 kJ) and does 110 kJ of work on the surroundings (W = 110 kJ).
So, ΔU = -690 kJ - 110 kJ = -800 kJ.
The change in internal energy of the system is -800 kJ.
Know more about internal energy here:
https://brainly.com/question/30207866
#SPJ11
what observation can you make that allows you to determine the relative magnitudes of the forces on the upper book?
Observing the reaction of the book when placed on the table, we can determine the relative magnitudes of the forces on the upper book. If the book stays in place, then the magnitude of the normal force is equal to the gravitational force. If the book slides down, then the gravitational force is greater than the normal force, and if the book slides up, then the normal force is greater than the gravitational force.
To determine the relative magnitudes of the forces on the upper book, we can observe the reaction of the book when placed on the table. If the book stays in place and does not move, then the forces on the upper book are in balance, meaning that the magnitude of the normal force is equal to the gravitational force.
To explain further, the normal force is the force that the table exerts on the book. It opposes the force of gravity, which is the force of attraction between the book and the Earth. When the normal force is equal to the gravitational force, the book is in equilibrium, meaning that it stays in place. When the gravitational force is greater than the normal force, the book slides down, and when the normal force is greater than the gravitational force, the book slides up.
for such more question on magnitudes
https://brainly.com/question/24468862
#SPJ11
a heat pump with a cop of 4.0 supplies heat to a building at a rate of 100 kw. determine the power input to the heat pump.
The power input to the heat pump is 25 kW.
The COP (coefficient of performance) of the heat pump is 4.0. This means that for every unit of power consumed by the heat pump, it supplies four units of heat to the building.
The rate at which the heat pump supplies heat to the building is 100 kW.
Therefore, the power input to the heat pump can be calculated as:
Power input = Power output / COP
Power input = 100 kW / 4.0
Power input = 25 kW
Hence, the power input to the heat pump is 25 kW.
To know more about power input click here:
https://brainly.com/question/1141300
#SPJ11
a spherical capacitor has vacuum between its conducting shells and a capacitance of 125 pf . the outer shell has inner radius 9.00 cm . what is the outer radius of the inner shell? express your answer with the appropriate units.
For a spherical capacitor with a capacitance of 125 and a vacuum between its conducting shells, the outer radius of the inner shell is around 5.60 cm.
The capacitance of a spherical capacitor is given by:
C = 4πε₀[(r₁r₂)/(r₂-r₁)]
where C is the capacitance, ε₀ is the electric constant (8.85 x [tex]10^{-12}[/tex] F/m), r₁ is the radius of the inner shell, and r₂ is the radius of the outer shell.
In this case, we know that the capacitance C = 125 pF (picoFarads), r₂ = 9.00 cm, and we want to find r₁.
We can rearrange the equation to solve for r₁:
r₁ = (C × r₂)/(4πε₀ + C)
Substituting the values:
r₁ = (125 x [tex]10^{-12}[/tex] F × 0.09 m) / (4π × 8.85 x [tex]10^{-12}[/tex] F/m + 125 x [tex]10^{-12}[/tex] F)
r₁ ≈ 5.60 cm
Therefore, the outer radius of the inner shell is approximately 5.60 cm.
To learn more about the capacitor at
https://brainly.com/question/17176550
#SPJ4
find the force between charges of +10.0 x 10*C and -50.0 x 10*C located 20>0cm apart
20 cm apart, the charges of +1.0 x 10⁻⁶ C and –1.0 x 10⁻⁶ C exert a force of 449.5 N on one another. This force is directed from the negative charge to the positive charge.
How can the force between two charges be determined?According to Coulomb's law, the force F between two point charges, q1 and q2, that are separated by a distance r, is computed as F=k|q1q2|r2.
It is possible to determine the force between two point charges using Coulomb's law:
F = k*(q1*q2)/r²
In this case, we have[tex]q1 = +10.0 x 10^-6 C, q2 = -50.0 x 10^-6 C, and r = 20 cm = 0.2 m.[/tex]
Plugging in these values, we get:
[tex]F = (8.99 x 10^9 N m^2/C^2) * [(+10.0 x 10^-6 C) * (-50.0 x 10^-6 C)] / (0.2 m)^2[/tex]
Simplifying, we get:
F = -449.5 N.
To know more about Charge visit:-
https://brainly.com/question/9194793
#SPJ1
I have no clue what im doing..
If work = 100J and time = 20 seconds, what is power
Answer:
5 J/s or 5 watt
Explanation:
Given,
Work (W) = 100 J
Time (t) = 20 s
To find : Power (P)
Formula :
P = W/t
P = 100/20
P = 5 J/s
P = 5 watt
Note : -
J/s and watt are units are power.
To determine the location of her center of mass, a physics student lies on a lightweight plank supported by two scales 2.50m apart, as indicated in the figure . If the left scale reads 290 N, and the right scale reads 112 N. What is the student's mass and find the distance from the student's head to her center of mass.
The location of her centre of mass, a physics student lies on a lightweight plank supported by two scales 2.50m apart, as indicated in the figure. If the left scale reads 290 N and the right scale reads 112 N The student's mass is approximately 41 kg, and the distance from her head to her centre of mass is approximately 0.696 m.
To determine the student's mass, we can sum up the readings from both scales, which are measures of force (Newtons) and then convert it to mass using the gravitational acceleration (g = 9.81 m/s²).
Step 1: Calculate the total force acting on the plank:
Total Force = Force_left_scale + Force_right_scale
Total Force = 290 N + 112 N
Total Force = 402 N
Step 2: Convert the total force to mass using gravitational acceleration:
Mass = Total Force / g
Mass = 402 N / 9.81 m/s²
Mass ≈ 41 kg
Now, to find the distance from the student's head to her centre of mass, we'll use the principle of torque equilibrium.
Step 3: Set up the torque equation:
Torque_left_scale = Torque_right_scale
Force_left_scale × Distance_left_scale = Force_right_scale × Distance_right_scale
Let x be the distance from the student's head to her centre of mass. Then, the distance from the left scale to the centre of mass is x, and the distance from the right scale to the centre of mass is (2.50 - x).
Step 4: Plug in the known values and solve for x:
290 N × x = 112 N × (2.50 - x)
Step 5: Simplify the equation and solve for x:
290x = 112(2.50) - 112x
290x + 112x = 112(2.50)
402x = 280
x ≈ 0.696 m
The student's mass is approximately 41 kg, and the distance from her head to her centre of mass is approximately 0.696 m.
For more such questions on centre of mass
brainly.com/question/28021242
#SPJ11
A 750-kg roller coaster car drops from rest at a height of 90.0 m along a frictionless track. If the coefficient of kinetic friction due to braking along a horizontal track at the end of the ride is 0.720, over what distance does the car need to brake to come to a complete stop?
A skydiver of mass 95kg ,before opening his parachute, falls at t1 with V1= 11m/s and at t2 with t2 v2=27m/s; supposing friction is zero, find the distance covered between t1 and t2
The skydiver covered a distance of approximately 94.9 meters before opening his parachute between t1 and t2, assuming no air resistance or friction.
v = final velocity = v2 = 27 m/s
u = initial velocity = v1 = 11 m/s
a = acceleration = g = 9.8 m/[tex]s^2[/tex]
s = (v² - u²) / 2a
s = (27² - 11²) / (2 x 9.8) = 94.9 meters
Resistance measures an item's potential to impede the drift of electrical present-day through it. it's far measured in ohms (Ω). Resistance is decided by way of the bodily residences of an item, along with its dimensions, material, and temperature. while electric-powered present-day flows thru a conductor, it encounters resistance that slows down its float. This resistance is as a result of the collisions among electrons and the atoms inside the conductor.
Resistance can be laid low with changes inside the bodily properties of the conductor, such as duration, cross-sectional region, or temperature. an extended or narrower conductor may have higher resistance, even as a much broader conductor could have decreased resistance. understanding resistance is critical for designing and working electrical circuits. with the aid of controlling the resistance of a circuit, engineers can make sure that the appropriate amount of current flows to electricity the devices linked to it.
To know more about Resistance visit here:
brainly.com/question/11431009
#SPJ4
A resistor and a capacitor are connected in series across an ideal battery. At the moment contact is made with the battery the voltage across the capacitor is
a. equal to the battery's terminal voltage. b. less than the battery's terminal voltage, but greater than zero. c. zero.
When a resistor and a capacitor are connected in series across an ideal battery, the voltage across the capacitor is zero at the moment contact is made with the battery.
The correct option is c.
An ideal battery is a voltage source that delivers a constant voltage regardless of the load resistance or current drawn from it.
An ideal battery can maintain a steady voltage regardless of the amount of current being drawn from it.
In real-life batteries, there is always some internal resistance, which causes the voltage to drop as the current increases.
A resistor is an electrical component that opposes or limits the flow of electrical current. It has two terminals and can be made of various materials like carbon, metal, and ceramic. It is used in various applications, including voltage dividers, current limiting, and biasing.
A capacitor is an electronic component that stores energy in an electric field between two charged conductors. It has two terminals and is made of two conducting plates separated by an insulating material called a dielectric.
Capacitors are used in various applications, including energy storage, timing circuits, and power conditioning.
To Learn more :
https://brainly.com/question/17134302
#SPJ11
A 23.3 kg boy is moving along a circular path with the constant speed of 2.7 m/s. What is the magnitude of the centripetal force acting on the boy if the radius of the circle is 12.9 m. Note : Calculate the answer to 3 (three) significant figures by presenting it in normal ( decimal) form. Don't forget to include the unit.
The centripetal force for the given question would be 16.3 N.
Explanation:
The magnitude of the centripetal force acting on a 23.3 kg boy moving along a circular path with a constant speed of 2.7 m/s and the radius of the circle is 12.9 m is 16.3 N (newton).
What is centripetal force?
Centripetal force is the net force acting on an object moving in a circular path toward the center of the circle. It always points towards the center of the circle, hence the name "center-seeking force".
What is the formula for centripetal force?
The formula for centripetal force is Fc = (mv²)/r, where Fc is the centripetal force, m is mass, v is velocity or speed and r is the radius of the circular path.
In the given question: Mass, m = 23.3 kgVelocity, v = 2.7 m/s, Radius, r = 12.9. To calculate centripetal force,
F = (m x v^2)/r
Putting the given values in the above formula: F = (23.3 kg x (2.7 m/s)^2)/12.9 m= 16.3 N (newton)
Therefore, the magnitude of the centripetal force acting on the boy is 16.3 N (newton).
To know more about centripetal force, visit:
https://brainly.com/question/11324711
#SPJ11
A dog can hear sounds in the range from 15
to 50,000 Hz.
What wavelength corresponds to the lower
cut-off point of the sounds at 20◦C where the
sound speed is 344 m/s?
Answer in units of m.
Explanation:
Speed of sound is 344
The frequency corresponding to the lower cut-off point is the lowest frequency which his 15Hz
F=15Hz
The relationship between the wavelength, speed and frequency is given as
v=fλ
Then,
λ=v/f
λ=v/f
λ=344/15
λ=22.93m
while the general equations for the first and second law are written in terms of how the universe changes, dr. laude's preference is that we quickly rewrite them to reflect changes in what?
This is due to the fact that the first and second laws of thermodynamics are universally applicable fundamental principles that can be utilised to examine particular systems and processes.
How do chemical processes relate to the first and second laws of thermodynamics?The part of thermodynamics that deals with chemical reactions is called chemical thermodynamics. The first law states that energy is conserved and cannot be created or destroyed. Second law: When natural processes in a closed system result in a rise in entropy, they are spontaneous.
The second law of thermodynamics is what?According to the second rule of thermodynamics, an isolated system that is out of equilibrium over time must increase in entropy until it reaches the ultimate equilibrium value.
To know more about thermodynamics visit:-
https://brainly.com/question/15591590
#SPJ1
the intensity of the sound of a television commercial is 10 times greater than the intensity of the television program it follows. by how many decibels does the loudness increase?
The television commercial loudness increases by 10 decibels.
Increase in the Intensity of soundThe decibel (dB) scale is a logarithmic measure of sound intensity. The intensity of a sound is measured in watts per square meter and the decibel scale is a way to express the relative loudness of a sound, compared to a reference level.
A 10 dB increase in intensity is a 10-fold increase in sound power. This means that a sound with an intensity of 10 watts per square meter is 10 times louder than a sound with an intensity of 1 watt per square meter.
Learn more about Intensity of sound here:
https://brainly.com/question/17062836
#SPJ1
explain the use of air bags and seat belts in terms of momentum and impulse. please provide examples (and calculations) to elaborate your concepts.
Answer:
Explanation:
A seatbelt is designed to stretch a bit when the car decelerates rapidly. You travel forward a little while being stopped - you do not stop sharply as you would if you hit the dashboard. The seatbelt stretching increases the time over which your momentum is changed, thereby decreasing the force experienced by your body.
Airbags are made from a strong coated fabric. They are stored in a module mounted on the steering wheel and dashboard and side panels of the car. The inflation of them is initiated by crash sensors that activate upon impact at speeds of more than 10-15 miles per hour. They are mounted in several locations on the car body. In a crash, the sensor sends an electrical signal to the airbag which then causes the airbag to deploy. It ignites a chemical propellant which produces nitrogen gas, which then inflates the bag itself.