if the tension in the cord is 110 n , how long will it take a pulse to travel from one support to the other?

Answers

Answer 1

We need to know the distance between the two supports and the speed at which the pulse travels along the cord. Let's assume that the distance between the supports is d meters and the speed of the pulse is v meters per second.

We can use the formula:

time = distance / speed

to find the time it takes for the pulse to travel from one support to the other. Rearranging this formula, we get:

distance = speed x time

So, if the tension in the cord is 110 N, we still need to know the speed of the pulse to calculate the time it takes to travel the distance.

Unfortunately, the tension in the cord alone does not provide enough information to determine the speed of the pulse. We need to know other factors such as the mass per unit length of the cord, the amplitude of the pulse, and the elasticity of the cord, among others.

Therefore, we cannot provide a specific answer to this question without additional information.

To know more about distance:

https://brainly.com/question/15172156

#SPJ11


Related Questions

The tire had an initial volume of 7 liters, at a temperature of 25° C. After driving for an hour, friction from the road had increased the temperature of air in the tire to 35° C. Assuming the pressure inside the tire did not change, what would the tire’s new volume be?

Answers

Answer:

using

V2= V1T2/T1

V2= 9.8L

a 1 540-kg automobile has a wheel base (the distance between the axles) of 3.10 m. the automobile's center of mass is on the centerline at a point 1.10 m behind the front axle. find the force exerted by the ground on each wheel.

Answers

The force exerted by the ground on each wheel of the automobile is 7560.3 N, which is half of the weight of the car.

How to find the force exerted by the ground on each wheel?

Since the center of mass is located 1.10 m behind the front axle, the distance between the center of mass and the rear axle is 3.10 m - 1.10 m = 2.00 m.

The weight of the automobile acts vertically downward through its center of mass and is given by:

W = mg

where

m = mass of the automobile

g = acceleration due to gravity = 9.81 m/s^2

Substituting the given values:

W = (1540 kg) * (9.81 m/s^2) = 15120.6 N

Assuming the weight is evenly distributed between the two wheels, the force exerted by each wheel can be found by considering the torque equilibrium of the automobile about the rear axle.

Since the automobile is in static equilibrium, the sum of the torques about any point is zero. Taking the rear axle as the pivot point, the torque due to the weight of the automobile is counteracted by the torques due to the forces exerted by the ground on the two wheels.

Let F1 and F2 be the forces exerted by the ground on the front and rear wheels, respectively. The torques due to these forces can be found using the distance between the wheels and the center of mass:

τ1 = F1 * 1.10 m (clockwise torque)

τ2 = F2 * 2.00 m (counterclockwise torque)

Since the automobile is in torque equilibrium, we have:

τ1 + τ2 = 0

Substituting the values and solving for F1 and F2:

F2 = (τ1/2.00 m) = (W/2) = 7560.3 N

F1 = (τ2/1.10 m) = (W/2) = 7560.3 N

Therefore, the force exerted by the ground on each wheel is 7560.3 N.

Learn more about Center of mass

brainly.com/question/28996108

#SPJ11

another capacitor, identical to the original, is added in series to the circuit described in the passage. compared to the original circuit, the equivalent capacitance of the new circuit is:

Answers

The equivalent capacitance of the new circuit with an identical capacitor added in series is half of the original circuit's capacitance.

When a second capacitor, identical to the original, is added in series to the circuit, the equivalent capacitance of the new circuit is reduced. This is because the total capacitance in a series circuit is always less than the individual capacitances. The formula for calculating the equivalent capacitance of a series circuit is:

[tex]1/Ceq = 1/C1 + 1/C2 + ... + 1/Cn[/tex]

Where C1, C2, ..., Cn are the capacitances of the individual capacitors.

Adding another capacitor in series to the circuit means that the equivalent capacitance will be smaller, and the total charge stored in the circuit will be less. This will affect the behavior of the circuit when connected to a voltage source, as it will take less time to charge and discharge.

Learn more about circuit's capacitance.

https://brainly.com/question/28884207

#SPJ4

voyager 1 is a space probe launched by nasa in 1977 and is the farthest human-made object. it experiences negligible gravity. voyager 1 is propelled by thrusters but will run out of fuel by 2040. what will happen to voyager 1 after this date?multiple select question.the velocity of voyager 1 will remain unchanged.voyager 1 will slow down from the velocity it will have when the fuel runs out.voyager 1 will immediately stop.voyager 1 will continue moving with the speed it will have when the fuel runs out.

Answers

Voyager 1 will continue moving with the speed it will have when the fuel runs out. The probe is traveling through the vacuum of space, where there is negligible gravity and no significant air resistance to slow it down.

Without the ability to adjust its trajectory, Voyager 1 will continue on its current path indefinitely unless it encounters a gravitational field that alters its trajectory. The probe may eventually drift off course and potentially collide with other celestial objects in its path. While Voyager 1 will continue to communicate data to Earth until its systems eventually fail, it will eventually become just another piece of space debris, floating silently through the cosmos.

Learn more about Voyager 1

https://brainly.com/question/3412409

#SPJ4

in a(n) ____ joint the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.

Answers

In a butt joint, the edges of the metal meet so that the thickness of the joint is approximately equal to the thickness of the metal.

In a butt joint, the edges of the metal pieces are placed together so that they are flush with one another, with little or no overlap. This results in a joint where the thickness of the joint is approximately equal to the thickness of the metal being joined. Butt joints are commonly used in welding and metal fabrication, as they provide a clean, simple joint that can be easily welded or brazed together. However, they may not be as strong as other types of joints, such as lap joints or T-joints, which provide more surface area for welding or brazing.

To learn more about metals, refer:-

https://brainly.com/question/28650063

#SPJ11

In welding, a joint refers to the area where two pieces of metal are joined together. There are several types of joints used in welding, including butt joints.

A butt joint is formed when two pieces of metal are placed together, edge to edge, and welded.

The joint is formed so that the thickness of the joint is approximately equal to the thickness of the metal being joined.

The process of making a butt joint involves

1) first preparing the edges of the metal.

2) This may involve grinding or filing to ensure that the edges are clean and straight.

3) The two pieces of metal are then brought together, with their edges touching, and held in place using clamps or other devices.

4) Once the pieces are in place, a welding machine is used to fuse the metal together.

The welding process may involve the use of heat or pressure, or a combination of both, depending on the type of welding being used.

The resulting joint is strong and durable, and is often used in a variety of applications where a strong, seamless joint is needed.

Butt joints are commonly used in the construction of buildings, bridges, and other structures, as well as in the manufacturing of machinery and equipment.

To know more about  butt joint visit link :

https://brainly.com/question/31733313

#SPJ11

after the switch s is closed, what will be the current in the circuit at the instant that the capacitors have lost 80.0% of their initial stored energy?

Answers

After switch S is closed, the capacitors in the circuit start to discharge.

The initial stored energy in the capacitors is given by [tex]1/2*C*V^2[/tex],

where C is the capacitance of the capacitors and V is the initial voltage across them.

As the capacitors discharge, the voltage across them decreases and so does the stored energy.

When the capacitors have lost 80.0% of their initial stored energy, the voltage across them will be 0.447 times the initial voltage.

At this point, the current in the circuit can be calculated using Ohm's law, which states that the current is equal to the voltage divided by the total resistance of the circuit.

Therefore, the current in the circuit at this point can be calculated as I = V/R, where V is the voltage across the capacitors and R is the total resistance of the circuit.

For more such answers on Capacitance
https://brainly.com/question/16998502

#SPJ11

a horizontal force of 80 n used to push a chair across a room does 320 j of work. how far does the chair move in this process?

Answers

The amount of work done by the force of 80 n is 320 j. Work is calculated by multiplying the force (F) by the distance (d) moved. Therefore, d = 320/80 = 4 m. This means that the chair moved 4 m in the process.

Energy is transformed into work when it takes another form.

In this instance, the chair is being moved across the room by the force of 80 n, which is transmitting its energy to it as labour. In joules (J), this energy is expressed.

As a result, the work produced by the force of 80 n is equivalent to the 320 J of energy that was transmitted. This quantity of energy is equivalent to the 4 m that the chair has travelled.

Complete Question:

A horizontal force of 80 n used to push a chair across a room does 320 j of work. How far does the chair move in this process?

To learn more about work visit:

https://brainly.com/question/25573309

#SPJ4

An inductor is connected to a 20 kHz oscillator that produces an rms voltage of 9.0 V. The peak current is 60 mA. What is the value of the inductance L? Final answer in mH. Please explain step by step.

Answers

The value of the inductance L is approximately 1193.25 mH.

To solve for the value of the inductance L, we can use the formula:

Vrms = Ipeak * (2 * pi * f * L)

where:

Vrms = 9.0 V

Ipeak = 60 mA = 0.06 A

f = 20 kHz

Substituting the values into the formula:

9.0 V = 0.06 A * (2 * pi * 20,000 Hz * L

Simplifying:

L = 9.0 V / (0.06 A * 2 * pi * 20,000 Hz)

L = 9.0 / (0.007536)

L = 1193.25 mH (rounded to two decimal places)

Therefore, the value of the inductance L is approximately 1193.25 mH.

Learn more about  inductance L

https://brainly.com/question/20471259

#SPJ4

An inductor is connected to a 20 kHz oscillator that produces an RMS voltage of 9.0 V. The peak current is 60 mA. The value of the inductance L is  1.692 mH.

Let's start by using the given information and then we'll solve for the value of the inductance L step by step:
1. Frequency of the oscillator (f) = 20 kHz = 20,000 Hz
2. RMS voltage (Vrms) = 9.0 V
3. Peak current (I_peak) = 60 mA = 0.06 A
Now, let's find the peak voltage (V_peak) using the relationship between RMS voltage and peak voltage:
Vrms = V_peak / √2
V_peak = Vrms * √2
V_peak = 9.0 V * √2 ≈ 12.73 V
Next, we'll calculate the impedance (Z) of the inductor using Ohm's law, which relates peak voltage and peak current:
Z = V_peak / I_peak
Z ≈ 12.73 V / 0.06 A ≈ 212.17 Ω
Now, we'll use the formula for the impedance of an inductor:
Z = 2 * π * f * L
Let's solve for the inductance L:
L = Z / (2 * π * f)
L ≈ 212.17 Ω / (2 * π * 20,000 Hz)
L ≈ 1.692 × 10^-3 H
Finally, convert the inductance L to millihenries (mH):
L ≈ 1.692 mH
So, the value of the inductance L is approximately 1.692 mH.

To learn more about inductor, refer:-

https://brainly.com/question/15893850

#SPJ11

based on the reading of the geiger counter, which type of radiation do you think is primarily emitted from the fiesta ware plate?

Answers

Based on the reading of the Geiger counter, it is likely that the Fiesta Ware plate is emitting beta radiation.

Beta radiation consists of high-energy electrons or positrons that can penetrate through skin and clothing but can be stopped by a thin sheet of metal. This type of radiation is commonly emitted by radioactive materials such as strontium-90, which was often used in the production of Fiesta Ware.

Beta radiation (β) is the transmutation of a neutron into a proton and an electron (followed by the emission of the electron from the atom's nucleus: e − 1 0 ). When an atom emits a β particle, the atom's mass will not change (because there is no change in the total number of nuclear particles).

To know more about Beta Radiation, please click:

brainly.com/question/16645044

#SPJ11

Earth's sky is blue during the day because:a. the molecules in the atmosphere scatter blue wavelengths of lightb. the atmosphere absorbs blue wavelengths of lightc. the sun produces more blue wavelengths than it produces in any other colord. red wavelengths are lost as solar radiation passes through the vacuum of space

Answers

The molecules in the Earth's atmosphere scatter blue wavelengths of light, making the sky appear blue during the day. The correct answer is a.

This phenomenon is known as Rayleigh scattering, which occurs when sunlight enters the Earth's atmosphere and interacts with the gas molecules in the air. The shorter, blue wavelengths of light are more easily scattered by the molecules in the atmosphere, while the longer, red wavelengths are less affected and continue to travel in a more direct path.

As a result, when we look up at the sky during the day, we see a blue color because the blue light is being scattered in all directions by the atmosphere. At sunrise and sunset, the sky appears more orange or red because the sun's light has to travel through more of the atmosphere, causing more scattering of the shorter, blue wavelengths and leaving more of the longer, red wavelengths to reach our eyes.

Learn more about  Earth's atmosphere

https://brainly.com/question/13154099

#SPJ4

when a fan is turned off, its angular speed decreases from 10 rad/s to 4.4 rad/s in 2.50 s. what is the magnitude of the average angular acceleration of the fan? a. 0.86 rad/s2 b. 2.24 rad/s2 c. 0.37 rad/s2 d. 11.0 rad/s2 e. 1.20 rad/s2

Answers

The magnitude of the average angular acceleration of the fan is 2.24 rad/s2 . So the correct answer is option: b.

The average angular acceleration can be calculated using the formula:

average angular acceleration = (final angular speed - initial angular speed) / time

Plugging in the given values, we get:

average angular acceleration = (4.4 rad/s - 10 rad/s) / 2.50 s

average angular acceleration = -2.56 rad/s2

Note that the negative sign indicates that the angular acceleration is in the opposite direction to the initial angular velocity.

|average angular acceleration| = 2.56 rad/s2 ≈ 2.24 rad/s2 .

Therefore, the correct answer is (b).

To know more about magnitude, here

brainly.com/question/14452091

#SPJ4

help please!!!!!!!!!!! ​

Answers

The circled vector on the diagram below represents the tension on the rope.

The option C is correct

What is  tension?

Tension is described as  the force transmitted through a string, rope, cable or wire when it is pulled tight by forces acting from opposite ends.

T = mg + ma

We know that the force of tension is calculated using the formula T = mg + ma.

In other terms, the pulling force that runs the length of a flexible connector, such a rope or cable, is known as tension. It is always pointed away from the force-applying object and along the length of the connector.

Learn more about tension at: https://brainly.com/question/24994188

#SPJ1

Modern geologists have abandoned relative dating methods in favor of more precise absolute dating methods. True/False

Answers

False. Here is a step-by-step explanation:

1) Relative dating methods and absolute dating methods are two types of techniques used by geologists to determine the age of rocks and fossils.

2) Relative dating methods involve the study of the relationships between different geological formations and the relative order in which they were formed.

3) Absolute dating methods use radiometric techniques to determine the age of a rock or fossil based on the decay rate of radioactive isotopes.

4) Modern geologists use both relative and absolute dating methods, depending on the specific research question and the available data.

5) Relative dating methods are often used to establish a chronological framework for a geological sequence, based on the order in which events occurred.

6) For example, relative dating can be used to determine which geological events came first, second, third, and so on, in a particular area.

7) Absolute dating methods, on the other hand, are used to assign an actual age to a rock or fossil.

8) Absolute dating methods are generally more precise than relative dating methods, but they require the use of specialized equipment and techniques.

9) In many cases, geologists use both relative and absolute dating methods to establish a comprehensive understanding of the geologic history of a particular area.

10) Therefore, the statement that modern geologists have abandoned relative dating methods in favor of more precise absolute dating methods is false, as both methods are still widely used in the field of geology.

To know more about Modern geologists :

https://brainly.com/question/28274168

#SPJ11

T/F : Staleness and burnout are not associated with overtraining.

Answers

False. Staleness and burnout are often associated with overtraining, which occurs when an individual exceeds their capacity to recover from intense physical training or activity.

Overtraining can lead to physical and psychological symptoms, including decreased performance, fatigue, irritability, and decreased motivation. It is important for individuals to listen to their bodies and take rest and recovery periods to prevent overtraining and associated symptoms.

To know more about Overtraining, please click:

brainly.com/question/5430690

#SPJ11

A proton accelerates from rest in a uniform electric field of 691 N/C. At some time later, it’s speed is 2. 30 x 10^6 m/s. (a) What is the magnitude of its acceleration? (b) How long does it take the proton to reach this speed

(c) How far has it moved in this time interval?

(d) What is its kinetic energy at the later time?

Mass of proton: 1. 6726x10^-27

Fundamental charge:

1. 602 x10^-19

Answers

The proton experiences an acceleration of [tex]$6.60\times10^{10} \text{m/s}^2$[/tex] in a uniform electric field of 691 N/C, and it takes [tex]$3.48\times10^{-5}$[/tex] s to reach a velocity of [tex]$2.30\times10^{6}$[/tex] m/s. During this time, the proton travels a distance of [tex]$4.36\times10^{-10}$[/tex] m and has a kinetic energy of [tex]$3.07\times10^{-12}$[/tex] J.

(a) The magnitude of the acceleration experienced by the proton can be determined by using the equation for the force on a charged particle in an electric field, which is F = qE, where F is the force, q is the charge of the particle, and E is the electric field strength. For a proton, the charge is equal to the fundamental charge, which is [tex]$1.602\times10^{-19} \text{C}$[/tex]. Therefore, the force on the proton is [tex]$F = (1.602\times10^{-19} \text{C})(691 \text{N/C}) = 1.106\times10^{-16} \text{N}$[/tex]

The acceleration of the proton can be determined using the equation F = ma, where m is the mass of the proton. Thus, [tex]$a = F/m = \dfrac{1.106\times10^{-16} \text{N}}{1.6726\times10^{-27} \text{kg}} = 6.60\times10^{10} \text{m/s}^2$[/tex].

(b) To find the time it takes for the proton to reach the given speed, we can use the kinematic equation v = u + at, where u is the initial velocity (which is 0 m/s), v is the final velocity ([tex]$2.30\times10^{6} \text{m/s}$[/tex]), a is the acceleration ([tex]$6.60\times10^{10} \text{m/s}^2$[/tex]), and t is the time. Rearranging this equation gives [tex]$t = \dfrac{v-u}{a} = \dfrac{2.30\times10^{6} \text{m/s}}{6.60\times10^{10} \text{m/s}^2} = 3.48\times10^{-5} \text{s}$[/tex].

(c) The distance the proton has moved in this time interval can be calculated using the kinematic equation [tex]$s = ut + \dfrac{1}{2}at^2$[/tex], where s is the distance traveled. Substituting the known values, we get [tex]$s = \dfrac{1}{2}(6.60\times10^{10} \text{m/s}^2)(3.48\times10^{-5} \text{s})^2 = 4.36\times10^{-10} \text{m}$[/tex]

(d) The kinetic energy of the proton can be calculated using the equation [tex]$KE = \dfrac{1}{2}mv^2$[/tex], where KE is the kinetic energy, m is the mass of the proton, and v is the velocity of the proton. Substituting the known values, we get [tex]$KE = \dfrac{1}{2}(1.6726\times10^{-27} \text{kg})(2.30\times10^{6} \text{m/s})^2 = 3.07\times10^{-12} \text{J}$[/tex].

To learn more about acceleration

https://brainly.com/question/12550364

#SPJ4

the four strings of a bass guitar are 0.865 m long and are tuned to the notes g (98 hz), d (73.4 hz), a (55 hz), and e (41.2 hz). in one bass guitar, the g and d strings have a linear mass density of 5.8 g/m, and the a and e strings have a linear mass density of 26.8 g/m. what is the total force exerted by the strings on the neck?

Answers

The total force exerted by the strings on the neck is 3061 N

We must determine the tension in each string and add it together to determine the overall force the strings are applying on the neck.

The wave speed equation may be used to determine the tension in a string:

v = fλ

where v is the speed of the wave (which is the same as the speed of the string), f is the frequency of the note, and λ is the wavelength of the wave (which is twice the length of the string).

For the g and d strings:

λ = 2(0.865 m) = 1.73 m

v = fλ

v_g = (98 Hz)(1.73 m) = 169.5 m/s

v_d = (73.4 Hz)(1.73 m) = 127.0 m/s

The tension in each string can be found using the wave equation:

T = [tex]μv^2/λ[/tex]

where T is the tension in the string, μ is the linear mass density of the string (mass per unit length), and v and λ are the speed and wavelength of the wave on the string.

For the g and d strings:

[tex]T_g = (5.8 g/m)(169.5 m/s)^2/1.73 m = 320 N[/tex]

[tex]T_d = (5.8 g/m)(127.0 m/s)^2/1.73 m = 196 N[/tex]

For the a and e strings

λ = 2(0.865 m) = 1.73 mv = fλ

v_a = (55 Hz)(1.73 m) = 95.2 m/sv_e = (41.2 Hz)(1.73 m) = 71.2 m/s

[tex]T_a = (26.8 g/m)(95.2 m/s)^2/1.73 m = 1643 N[/tex]

[tex]T_e = (26.8 g/m)(71.2 m/s)^2/1.73 m = 902 N[/tex]

The total force exerted by the strings on the neck is:

F_total = T_g + T_d + T_a + T_e

F_total = 320 N + 196 N + 1643 N + 902 N

F_total = 3061 N

Learn more about total force

https://brainly.com/question/30149537

#SPJ4

what is the largest x-ray wavelength that can be diffracted by crystal planes with a separation of 0.316 nm?

Answers

The largest x-ray wavelength that can be diffracted by crystal planes with a separation of 0.316 nm is 0.632 nm.

To find the largest X-ray wavelength that can be diffracted by crystal planes with a separation of 0.316 nm, we can use Bragg's Law:

nλ = 2d sinθ

where n is an integer representing the order of diffraction, λ is the wavelength, d is the separation between crystal planes (0.316 nm), and θ is the angle of incidence. To find the largest possible wavelength, we need to consider the lowest order of diffraction (n = 1) and the maximum angle of incidence (θ = 90°).

Now we can plug in the values and solve for λ:

1λ = 2(0.316 nm) sin(90°)

λ = 2(0.316 nm) * 1

λ = 0.632 nm

The largest X-ray wavelength that can be diffracted by crystal planes is 0.632 nm.

Learn more about Bragg's Law:

https://brainly.com/question/14617319

#SPJ11

The __________ notation of entity-relationship modelling can be used for both conceptual and implementation modelling.
a. Bachman
b. UML
c. Chen
d. Crow's Foot

Answers

The Chen notation of entity-relationship modelling can be used for both conceptual and implementation modelling.

The Chen notation of entity-relationship modelling can be used for both conceptual and implementation modelling. Notation refers to the symbols and conventions used to represent concepts in a model. Entity-relationship modelling is a technique used in database design to represent the relationships between entities. Conceptual modelling is the process of creating a high-level representation of a system, while implementation modelling involves creating a detailed representation of the system's implementation.

To learn more about Chen notation Here:

https://brainly.com/question/28234454

#SPJ11

calculate the change in energy for the following process: how much energy (in kcal) must be removed from 0.811 kg of water to cool it from 91 oc to 15 oc?

Answers

The amount of energy that must be removed from 0.811 kg of water to cool it from 91°C to 15°C is approximately 61.636 kcal.

To calculate the change in energy for this process, we will use the specific heat capacity of water and the equation:

[tex]Q = m . c .[/tex]ΔT

where:
Q = change in energy (in kcal).
m = mass of water (in kg).
c = specific heat capacity of water (in kcal/kg°C).
ΔT = change in temperature (in °C).

The specific heat capacity of water is approximately 1 kcal/kg°C.

First, we need to determine the change in temperature (ΔT). To do this, subtract the final temperature (15°C) from the initial temperature (91°C):

Δ[tex]T = 91^{O}C - 15^{O}C = 76^{O}C[/tex]
Now, plug in the values into the equation:
[tex]Q = m . c .[/tex]ΔT
[tex]Q = (0.811 kg) . (1 kcal/kg°C) . (76°C)\\Q = (0.811 kg) . ( 76 kcal/°C)\\Q = 61.636 kcal\\[/tex]

Therefore, 61.636 kcal of energy must be removed from 0.811 kg of water to cool it from 91°C to 15°C.

Learn more about the amount of energy that must be absorbed or lost to raise or lower the temperature, at: https://brainly.com/question/29418076

#SPJ11

maxwell's equations are a complete description of electric and magnetic fields. how many equations are there?

Answers

Maxwell's equations are a complete description of electric and magnetic fields. There are four equations in Maxwell's equations. These four equations are:

1. Gauss's Law for Electric Fields: Describes the relationship between electric charges and the electric field produced by them.
2. Gauss's Law for Magnetic Fields: States that there are no magnetic monopoles, and the magnetic field lines are always closed loops.
3. Faraday's Law of Electromagnetic Induction: Describes the induced electromotive force (EMF) in a closed circuit produced by a changing magnetic field.
4. Ampere's Law with Maxwell's Addition: Relates the magnetic field around a closed loop to the electric current passing through the loop and the rate of change of the electric field.

These four equations collectively provide a comprehensive description of electric and magnetic fields and their interactions.

To know more about Ampere's Law with Maxwell's Addition:

https://brainly.com/question/29831953

#SPJ11

mine C contient 1000 mg
d'acide ascorbique. Il
se prend dans un verre
d'eau de 20 CL.
1. Une orange contient
115 mg d'acide ascorbique. Combien faut-il d'oranges
pour obtenir la même masse d'acide ascorbique que
le comprimé ?
2. Il faut environ trois oranges pour obtenir 200 mL de
jus. Quelle est la concentration en acide ascorbique
du jus d'orange ?
3. Quel volume de la solution obtenue avec le comprimé
dans le verre contient la même masse d'acide ascor-
bique que ces trois oranges ?
4. Quel volume d'eau faut-il ajouter au verre contenant
le comprimé pour obtenir la même concentration en
acide ascorbique que le jus d'orange ?

Answers

Answer:

Explanation: honestly i don’t speak spanish so please explain with english

A compound microscope is a two-lens system used to look at very small objects. Which of the following statements is correct? The objective lens is a short focal length, convex lens and the eyepiece functions as a simple magnifier. The objective lens is a long focal length, convex lens and the eyepiece functions as a simple magnifier. The objective lens and the eyepiece both have the same focal length and both serve as simple magnifiers. The objective lens is a short focal length, concave lens and the eyepiece functions as a simple magnifier. The objective lens is a long focal length, concave lens and the eyepiece functions as a simple magnifier.

Answers

The objective lens is a long focal length, convex lens and the eyepiece functions as a simple magnifier is the correct statement about a compound microscope. Option b is correct.

In a compound microscope, the objective lens is a long focal length, convex lens that produces an inverted, magnified real image of the specimen. The eyepiece, on the other hand, functions as a simple magnifier, which further magnifies the real image produced by the objective lens and forms a virtual image that can be viewed by the observer's eye. Therefore, option b is the correct statement.

To know more about microscope, here

brainly.com/question/18661784

#SPJ4

--The complete question is, A compound microscope is a two-lens system used to look at very small objects. Which of the following statements is correct?

a. The objective lens is a short focal length, convex lens and the eyepiece functions as a simple magnifier.

b. The objective lens is a long focal length, convex lens and the eyepiece functions as a simple magnifier.

c.  The objective lens and the eyepiece both have the same focal length and both serve as simple magnifiers.--

to resolve two point sources, what distribution of cones must occur where the image strikes the retina?

Answers

The distribution of cones at the point of image formation is crucial in resolving two point sources

To resolve two point sources, a distribution of cones must occur where the image strikes the retina. Cones are responsible for color vision and high acuity vision, making them essential for resolving fine details such as two point sources.

In order for the brain to distinguish between two closely spaced points, each point must stimulate different cones. This can be achieved by having a distribution of cones at the point of image formation.

The cones should be spaced closely together to ensure that each point is detected by separate cones. The density of cones in the fovea, the area of the retina responsible for high acuity vision, is highest, allowing for the greatest resolution of point sources. .

To learn more about : distribution

https://brainly.com/question/28027633

#SPJ11

3. When the procedure is repeated with a third line how will it distinguish whether the location of the center of gravity is accurate or not?​

Answers

If the procedure is repeated with a third line, it will distinguish whether the location of the center of gravity is accurate or not by checking if the intersection point of the three lines passes through the same point as the previous two lines.

This is because the intersection of the third line with the other two lines should also pass through the same point as the previous two lines if the location of the center of gravity is accurate. If the intersection point of the third line is not consistent with the previous two, then it suggests that the location of the center of gravity is not accurate.

To know more about intersection point , here

brainly.com/question/14217061

#SPJ4

How much heat does it take to raise the temperature of 5.0 kg of plastic from 15°C to 75°C? The specific heat of plastic is 2.60 kJ/(kg × °C).

Answers

where

m is the mass

c is the specific heat capacity

ΔT is the change in temperature

In your problem,

m=2.5 kg

c=2.60 kJ⋅°C-1kg-1

Δ

∴ q=2.5kg×2.60 kJ⋅°C-1⋅kg-1×60°C=390 kJ

A 55 kg skater is gliding along the ice at a velocity of 8 m/s to the right while holding a 3 kg ball. The skater throws the ball at a velocity of 4 m/s to the right. What will be the skaters velocity after throwing the ball?

Answers

Answer:

Speed of Skater = 8.16 m/s

Explanation:

Using kinetic energy:

[tex]M_{t} = M_{skater} + m_{ball}\\\frac{1}{2}M_{t}V_{i}^2 = \frac{1}{2}*M*V_{s} ^2+\frac{1}{2}*m*V_{b}^2\\ M_{t}V_{i}^2 = M_{s}*V_{s} ^2+m_{b}*V_{b}^2\\M_{t}V_{i}^2-m_{b}*V_{b}^2 = M_{s}*V_{s} ^2\\(M_{t}V_{i}^2-m_{b}*V_{b}^2)/M_{s} = V_{s} ^2\\V_{s} = \sqrt{\frac{(M_{t}V_{i}^2-m_{b}*V_{b}^2)}{M_{s}} } \\[/tex]

This gives the skater a velocity of 8.16 m/s after throwing the ball

A student collected the data below on the time and distance traveled by a beetle.
Flight of a Beetle
OB. 1 m/s
O C. 1.25 m/s
Distance in meters (m)
OD. 4 m/s
€5.0
4.0
1.0 2.0 3.0 4.0 5.0
Time in seconds (s)
What was the beetle's average flight speed during the time represented in the graph?
O A. .75 m/s
3.0
2.0
1.0

Answers

Answer: the correct answer is option C) 1.25 m/s.

Explanation: The formula for average speed can be expressed as the quotient of the total distance traveled divided by the total time elapsed.

Upon examination of the presented graphical representation, it is evident that the beetle traversed a cumulative distance of 5 meters within a duration of 4 seconds.

Thus, it can be observed that the mean velocity of the beetle would be:

The mean velocity of the object is 5 meters per 4 seconds.

The mean velocity is equivalent to 1.25 meters per second.

The data depicted in the aforementioned graph indicates that the average velocity of the beetle during its flight is 1.25 meters per second.

Based on the Doppler effect, the electromagnetic waves reaching Earth from a galaxy that is moving away from Earth would be
expected to
O experience an increase in frequency.
O experience a decrease from transverse waves to longitudinal waves.
O experience a decrease in frequency
O experience an increase in their amplitude.
7
8
9 10 11 12 13 14 15 16 Next

Answers

Based on the Doppler effect, the electromagnetic waves reaching Earth from a galaxy that is moving away from Earth would experience a decrease in frequency.

option C.

What is Doppler effect?

The Doppler effect is a phenomenon where the frequency of waves (such as electromagnetic waves or sound waves) is shifted as a result of the relative motion between the source of the waves and the observer. When a source of waves is moving away from an observer, the waves get stretched out, resulting in a decrease in frequency. This is known as redshift for light waves, which are a type of electromagnetic waves.

In the context of a galaxy moving away from Earth, the electromagnetic waves (such as light) emitted by the galaxy would experience a redshift, which means the frequency of the waves would decrease. This is a key observation in astronomy and cosmology that has been used to provide evidence for the expanding universe and the Big Bang theory, as galaxies in the universe are generally observed to be moving away from each other, causing their light to be redshifted.

Learn more about doppler effect here: https://brainly.com/question/3841958

#SPJ1

a projectile of mass 1.3 kg is launched horizontally from an initial height 2.9 m with an initial velocity 8.5 m/s. this velocity in the x direction is preserved when you ignore air resistance. the projectile still accelerates in the vertical y direction toward the ground, but this is exactly the energy lost from potential energy. energy is conserved as long as you use the total mechanical energy equation. what is the total final kinetic energy (joules) as the projectile just reaches the ground? give your numerical answer to one decimal place precision. assume g

Answers

The total final kinetic energy of the projectile as it reaches the ground is 49.5 J (to one decimal place of precision).

Applying conservation of energy

To solve this problem, we need to use the conservation of energy principle. The initial total mechanical energy (potential plus kinetic) of the projectile is converted into its final total mechanical energy when it reaches the ground, assuming no energy is lost due to air resistance.

The initial potential energy is given by:

Ep = mgh = (1.3 kg)(9.81 m/s^2)(2.9 m) = 36.01 J

The initial kinetic energy in the x-direction is given by:

Kx = 0.5mvx^2 = 0.5(1.3 kg)(8.5 m/s)^2 = 49.47 J

Since there is no initial kinetic energy in the y-direction, the total initial mechanical energy is the sum of the initial potential and kinetic energies in the x-direction:

Ei = Ep + Kx = 36.01 J + 49.47 J = 85.48 J

At the final moment, the projectile reaches the ground, so its final potential energy is zero. Therefore, the final total mechanical energy is equal to the final kinetic energy:

Ef = Kf

We know that the projectile is subject to constant acceleration due to gravity (9.81 m/s^2) in the y-direction, and we can use the kinematic equation:

y = yo + voyt + 0.5a*t^2

where y is the final position (0 m), yo is the initial position (2.9 m), voy is the initial velocity in the y-direction (0 m/s), a is the acceleration due to gravity (-9.81 m/s^2), and t is the time it takes for the projectile to reach the ground.

Rearranging this equation to solve for t, we get:

t = sqrt(2(y - yo)/a) = sqrt(2(0 - 2.9)/(-9.81)) = 0.762 s

Now we can use the final velocity in the x-direction and the time of flight to calculate the final kinetic energy in the x-direction:

Kxf = 0.5mvx^2 = 0.5(1.3 kg)(8.5 m/s)^2 = 49.47 J

Therefore, the final total mechanical energy and final kinetic energy are:

Ef = Kf = Kxf = 49.47 J

Therefore, the total final kinetic energy of the projectile as it reaches the ground is 49.5 J (to one decimal place of precision).

Learn more on kinetic energy here https://brainly.com/question/8101588

#SPJ1

the value of the total radiant energy flux density at the earth from the sun normal to the incident rays is called the solar constant of the earth. the observed value integrated over all emission wavelengths and referred to the mean earth-sun distance is:

Answers

The observed value of the total radiant energy flux density at the earth from the sun, integrated over all emission wavelengths and referred to the mean earth-sun distance, is approximately 1,366 watts per square meter.

This value is known as the solar constant and is an important factor in understanding the earth's climate and energy balance. It represents the amount of solar energy that is received per unit area at the top of the earth's atmosphere and is a key input for models of global climate change.

Learn more about energy flux

https://brainly.com/question/30480603

#SPJ4

Other Questions
A small can of tomato paste has a radius of 2 inches and a height of 4 inches. Suppose the larger, commercial-size can has dimensions that are related by a scale factor of 3. Which of these is true? The area of the circle is 9/64 square units. The radius of a circle is blank units. The circumference of the circle is blank units.*One radius and one circumference*a. 9/32b. 3/8c. 3/4d. 9/32e. 3/8f. 3/4 when was the number of communities using surveillance cameras at intersections changing least rapidly? What were the conditions before Storm 1, and why did more rain fall with those conditions? Im a normal high school kidthat is, I like listening to music. Until about a year ago, I always liked listening to it loud. Loud enough that it filled up my head and pulsed through my body, so the boundary between me and the music disappeared. Ive listened to countless hours of musicvibrant music pouring into my ears through my headphones, washing over me from car speakers, or blasting at me from gigantic speakers at concerts. But theres something about me that makes me not so normal. I have a hearing loss and a constant ringing in my ears that, unless some medical miracle happens, Ill suffer from these impairments forever. My ear problems are so severe that I feel I need to warn you: You have to protect your hearing as much as you can.What conclusion can be made about the narrator of this reading? east coast yachts goes international what are the implications for this approach?how can the company hedge its exchange rate risk? what are the implications for this approach? A tram moved downward 12 meters in 4 seconds at a constant rate. What was the change in the tram's elevation each second? this is a session that takes place without a jury before a judge in which evidence and/or arguments are presented to determine some factual or legal issue. A. HearingB. DiversionC. Commitment 2. A student prepared a 0.500 M solution of an unknown acid, and measured the pH as 3.56 at 25C. (a) What is the acid dissociation constant of this unknown acid? (b) What percentage of acid is ionised in this solution a trapezoid has an area of 96 ft. if the base is 11 feet and the height is 8 feet, what is the length of the other base Have you wrote to us regarding this issue before boycotts, work slowdowns, and corporate campaigns have increased since the 1980s because? A. Empoyees have become more militant.B. Strikes are no longer a viable option for many workers because of the employer's use of permanent strike replacementsC. Strikes are less costly to employers because they have more inventory today.D. Strikes are no longer legal in most situations. What does it mean when we say our sense of motion depends on our frame of reference? Include the phrases fixed frame and moving frame in your answer. You can give the tour guide a tip but it is not necessary.You __________________________ give the tour guide a tip. I need help with a college assignment I dont have time to do it and its reading a short essay and answering some questions if you could take the time to help it would be very much appreciated It has been said that most systems fail because system builders ignore organizational behavior problems. Why might this be so? Add refrence ABC Plc , in its 2021 finance statements is reporting total equity of 1572, total non-current liabilities of 200, gross profit of 400 and operating profit of 88. What is the Return on Capital employed as a percentage?a. 4.97%b. 44%c. 20.14%d.25.45% explain how a patient could have red blood cells in the urine even if the filtration membrane were still intact Name the agency of the Department of Justice charged with enforcing laws against narcotics trafficking.a. NCIC b. Secret Service c. DEA d. SSA If the production function is Q = 30 + 33L + 16K, whats themost you can produce with 5 workers (L) and 3 unit of capital (K)?Enter as a value.