The Low-Level Wind Shear Alert System (LLWAS) provides wind data and software processes to detect the presence of hazardous wind shear.
LLWAS (Low-level windshear alerting systems) is a tool with a system to detect the presence of windshears close to the airport, and will provide warning windshear information automatically if has exceeded its threshold.
It works by collecting data from wind speed and direction sensors located around an airport to provide real-time monitoring of changes in wind direction and speed that can lead to hazardous wind shear events. The data is used to create an alert if hazardous wind shear is detected.
Learn more about LLWAS : https://brainly.com/question/30001468
#SPJ11
how does the sovent drainage and waste system operate without the venting piping used in traditional systems?
The solvent drainage and waste system operates without venting piping by using a combination of air flow and pressure.
Instead of relying on venting piping to exhaust fumes and waste, the system takes in air from the atmosphere and circulates it through the system with a blower or compressor. This creates a pressure difference that drives the solvent out of the system, taking any remaining waste with it. The pressure also keeps odors from escaping and prevents the system from backflowing.
Drainage is the removal of a mass of water either naturally or artificially from the surface or subsurface from a place.
Learn more about drainage : https://brainly.com/question/831589
#SPJ11
The XYZ Company is planning a new product line and a new factory to produce the parts and assemble the final products. The product line will include 13 different models. Annual production of each model is expected to be 1,000 units. Each product will be assembled of 250 components, but 65% of these will be purchased parts (not made in the new factory). There is an average of 8 processing operations required to produce each component, and each processing step takes 30 sec (including an allowance for setup time and part handling). Each final unit of product takes 48 min to assemble. All processing operations are performed at work cells that include a production machine and a human worker. Products are assembled at single workstations consisting of one worker each plus assembly fixtures and tooling. Each work cell and each workstation require 25 m2 of floor space and an additional allowance of 45% must be added to the total production area for aisles, work-in-process storage, shipping and receiving, rest rooms, and other utility space. The factory will operate one shift (the day shift, 2,000 hr/yr). Determine: (a) how many processing and assembly operations, (b) how many workers (direct labor only), and (c) how much total floor space will be required in the plant.
The plant will need to perform 9,100,000 processing and assembly procedures altogether.
What fundamental processing tasks are carried out in a manufacturing facility?Shape operations, property-enhancing operations, and surface processing operations are the three distinct categories of processing operations. By using mechanical force, heat, or other forms and combinations of energy, shaping operations change the work material's geometry.
There are 250 components in each product.
Parts purchased as a percentage equal 65%.
250 - (65% x 250) = 87.5 is the number of components that will be produced in the new facility.
Eight processing steps are needed to manufacture each component.
The new factory's processing procedures per component totaled 8 x 87.5, or 700.
13 x 1000 x (700 + 1) = 9,100,000 is the total number of processing and assembly procedures needed for the 13 different models.
To know more about assembly visit:-
https://brainly.com/question/13557244
#SPJ1
air is compressed steadily and adiabatically from 290k, 90 kpa to 480k, 390 kpa. what is the isentropic efficiency of the compressor? a
The Isentropic efficiency of the compressor Let's consider the given parameters; Initial conditions: T1 = 290 kP1 = 90 kPa Final conditions: T2 = 480 kP2 = 390 kPa The isentropic efficiency of the compressor can be calculated using the following formula:ηs = (h2s - h1) / (h2 - h1)Whereηs = Isentropic efficiency of the compressorh1 = Enthalpy at the inlet of the compressorh2 = Enthalpy at the outlet of the compressorh2s = Isentropic enthalpy at the outlet of the compressor.
Now let's calculate the enthalpies; From the given conditions, we can find out the state point of the air at the inlet of the compressor using the steam tables: At P1 = 90 kPa, T1 = 290 K Using the steam tables, we find out h1 = 315.83 kJ/kg Similarly, we can find out the state point of the air at the outlet of the compressor using the steam tables: At P2 = 390 kPa, T2 = 480 K Using the steam tables, we find out h2 = 421.45 kJ/kg Now, let's calculate the isentropic enthalpy at the outlet of the compressor: Using the steam tables, we can find out the state point of the air at the outlet of the compressor if it were isentropic. At P2 = 390 kPa and S1 = S2Using the steam tables, we find out h2s = 455.41 kJ/kg Substituting these values in the isentropic efficiency formula, we get;ηs = (h2s - h1) / (h2 - h1)ηs = (455.41 - 315.83) / (421.45 - 315.83)ηs = 0.72Thus, the isentropic efficiency of the compressor is 72%.
for more such questions on parameters.
https://brainly.com/question/30380032
#SPJ11
3
Biocatalysis helps create flavors and scents through what process?
altering DNA
chemical reactions
purifying components in a formula
aiding with the decomposition process
Answer:
its B. ima keep it short its B
Explanation
what is the purpose of the ground symbol used in electrical circuit diagrams? group of answer choices to show that there is a return path for the current between the source of electrical energy and the load. to show the source of electrical energy for the load. to show that there is common bus for connection of the source of electrical energy to the load.
Answer:
To show that there is a return path for the current between the source of electrical energy and the load.
calculate the cumulative infiltration and the infiltration rate on a silty clay soil after one hour of rainfall at 1cm/h if the initial effective saturation is 20 percent. assume ponding depth h0 is negligible in the calculations.
The cumulative infiltration and infiltration rate on a silty clay soil after one hour of rainfall at 1cm/h with initial effective saturation of 20 percent are 252 cm and 4.21 cm/h, respectively.
To calculate the cumulative infiltration and the infiltration rate on a silty clay soil after one hour of rainfall at 1cm/h if the initial effective saturation is 20 percent, we need to first calculate the cumulative infiltration (Icum) and infiltration rate (f). The cumulative infiltration is given by the equation: Icum = h0 + ∫f (dt). Here, h0 is negligible and ∫f (dt) = f x t. So, Icum = f x t.
The infiltration rate can be calculated using the Kostiakov equation: f = K x t1/2. Here, K is the Kostiakov coefficient, which is a function of the initial effective saturation (Si). For a silty clay soil, K = 0.0026 x Si0.5 (cm/min1/2). Thus, in this case, K = 0.0026 x 200.5 = 0.164 cm/min1/2. Since the rainfall intensity is 1 cm/h, t = 1 hour = 60 min. So, the infiltration rate, f = 0.164 x 601/2 = 4.21 cm/h. The cumulative infiltration is Icum = 4.21 x 60 = 252 cm. So, the answers are 252 cm and 4.21 cm/h, respectively.
Learn more about infiltration rate : https://brainly.com/question/28992374
#SPJ11
which safety hazard are firefighters most likely to find in the space between the ceiling and the roof?
Firefighters are most likely to find the following safety hazards in the space between the ceiling and the roof: accumulation of combustible material, poor ventilation, and exposure to hazardous chemicals.
Accumulation of combustible materials such as wood, paper, insulation, and other debris can provide fuel for a fire, which can be difficult to contain in a confined space like the one between a ceiling and a roof.
Poor ventilation in this space can make it difficult for firefighters to breathe, and they can be exposed to hazardous chemicals such as asbestos, lead, and dust. Firefighters have to be careful with that.
Learn more about Firefighters : https://brainly.com/question/25483991
#SPJ11
in the context of dynamic person-situation interaction, the main difference between evocation and manipulation is that:
Manipulation involves the intentional control of a situation by a person, whereas evocation is the process through which people elicit responses from others simply by displaying certain behaviors.
Manipulation is a term used in psychology to refer to the intentional control of a situation or environment by a person. It can be used to gain control over others, influence their behavior, or alter their perceptions.
Manipulation can be positive or negative, depending on the intention of the person doing the manipulating. Some forms of manipulation may involve deception, coercion, or exploitation.
On the other hand, evocation is a process through which people elicit responses from others simply by displaying certain behaviors. This is often done unintentionally, without the person being aware that they are having an impact on others.
Unlike manipulation, evocation does not involve intentional control over a situation or environment.
Learn more about manipulation here:
https://brainly.com/question/27154551
#SPJ11
the equation used to determine the approximate amount of of critical stress to propagate a crack is known as the friffith equation the griffith equation is
The Griffith equation is used to calculate the approximate amount of critical stress necessary to propagate a crack. The formula for the equation is K = √(πE/2Y), where E is Young's modulus, and Y is the geometrical factor, which depends on the shape of the crack.
The equation is based on the energy release rate for crack propagation and was developed by A.A. Griffith in 1921. The equation is used to calculate the stress intensity factor (K) for a crack in an elastic material.
The Griffith equation is important for engineers as it can be used to estimate how much stress a material can withstand before it will fracture. This is important when designing components or structures that will be subject to loading or fatigue. Additionally, the equation can be used to calculate the stress concentration factor (Kt) at a point of crack initiation.
In conclusion, the Griffith equation is an important equation used to calculate the approximate amount of critical stress necessary to propagate a crack. This equation can be used by engineers to ensure that their designs are able to withstand the expected loads, as well as calculate stress concentration factors.
You can learn more about Griffith at: brainly.com/question/30188283
#SPJ11
Truss ABC is changed by decreasing its height from H to 0.9 H. Width W and load P are kept the same. Which one of the following statements is true for the revised truss as compared to the original truss?
A. Force in all its members have decreased.
B. Force in all its members have increased.
C. Force in all its members have remained the same.
D. None of the above.
Force in all its members have increased
Force EquationThe vector product of mass (m) and acceleration (a) expresses the quantity of force (a). The force equation or formula can be expressed mathematically as follows:
F = ma In which case,
m = mass a = velocity
It is expressed in Newtons (N) or kilogrammes per second.
The acceleration an is provided by
a = v/t
Where
v = acceleration
t = time spent
As a result, Force can be expressed as follows:
F = mv/t
The formula for inertia is p = mv, which can also be expressed as Momentum.
As a result, force can be defined as the rate of change of momentum.
dp/dt = F = p/t
Force formulas are useful for determining the force, mass, acceleration, momentum, and velocity in any given problem.
To know more about Force,click on the link :
https://brainly.com/question/13191643
#SPJ1
Please give a detail explanation, thank you
1) When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies.
True or false
2) If a semi-truck collides head-on with a mini car, which one will exert more force?
Semi-truck on the mini car
Mini car on the semi-truck
There is no force exerted
Both vehicles will exert equal force
The given statement "When solving the impact problems, we should always assume that during an impact between two bodies, there is no permanent deformation in the bodies" is False and there is usually some amount of permanent deformation during an impact when semi-truck collides head-on with a mini car.
The statement is False because In reality, there is usually some amount of permanent deformation that occurs during an impact, especially if the impact is severe. However, in many cases, the amount of deformation may be negligible or can be ignored for simplicity in calculations.Therefore the statement is False.
If a semi-truck collides head-on with a mini car then According to Newton's Third Law of Motion, every action has an equal and opposite reaction. Therefore, both the semi-truck and the mini car will exert equal force on each other during a head-on collision. The force experienced by each vehicle will depend on factors such as their mass, speed, and the duration of the impact. However, it is likely that the semi-truck, being much larger and heavier than the mini car, will experience less of a change in velocity than the mini car and therefore will exert more force on the smaller vehicle.
To practice more questions on force:
https://brainly.com/question/12970081
#SPJ11
Which is a small plain text file that a website might place on your local drive?
Answer:A cookie
Explanation:To track interests.
what is an impact, ballistic or creep ripple? what is the length of these ripples relative to their heights? how does this ratio compare to those for aerodynamic and hydrodynamic ripples?
Impact, ballistic, and creep ripples are all types of surface features that can occur on materials subjected to different types of stresses.
Impact ripples are formed when a material is struck by a projectile or another object. Ballistic ripples are similar but are specifically formed by high-velocity projectiles. Creep ripples, on the other hand, are formed when a material is subjected to a constant stress over a long period of time, causing it to slowly deform.
The length of these ripples relative to their heights can vary depending on the specific material and conditions. However, in general, the ripples tend to have a relatively short wavelength compared to their height.
In comparison, aerodynamic and hydrodynamic ripples are formed by the flow of air or water over a surface. These ripples tend to have a much longer wavelength compared to their height, with the length-to-height ratio typically ranging from several to tens of thousands. This is because the fluid flow over the surface is generally much smoother and less abrupt than the stresses that cause impact, ballistic, and creep ripples.
To learn more about stresses refer to:
brainly.com/question/30128830
#SPJ4