what could the maxwell equation below be used for? select the correct answer select this answer if none of the choices are valid your answer to predict the electric field in a region of space containing many charged particles to predict what currents need to flow through wires to produce a certain electric field to predict the magnetic field in a region of space in which the electric flux is changing to predict the magnetic flux through a closed surface

A  system releases 690 kj of heat and does 110 kj of work on the surroundings then part a what i the change in internal energy of the system  -800 kJ.

The change in internal energy of the system can be calculated using the formula

ΔU = Q - W,

where ΔU is the change in internal energy, Q is the heat exchanged, and W is the work done.

In this case, the system releases 690 kJ of heat (Q = -690 kJ) and does 110 kJ of work on the surroundings (W = 110 kJ).

So, ΔU = -690 kJ - 110 kJ = -800 kJ.

The change in internal energy of the system is -800 kJ.

Know more about   internal energy   here:

https://brainly.com/question/30207866

#SPJ11

Among the given options, the appliance with the lowest typical energy cost is the microwave oven. Typical energy cost refers to the average amount of money spent on energy usage by an appliance or device over a certain period of time.

Microwave ovens use electromagnetic radiation to cook or heat food, and they are generally more energy-efficient compared to other appliances such as dishwashers, washing machines, and refrigerators. This is because microwave ovens use less power and cook food faster than conventional ovens, reducing energy waste and costs. However, it is important to note that the exact energy cost of an appliance can depend on factors such as its age, model, usage, and energy efficiency rating.

Learn more about microwave ovens: https://brainly.com/question/1120515

#SPJ11

When a resistor and a capacitor are connected in series across an ideal battery, the voltage across the capacitor is zero at the moment contact is made with the battery.

The correct option is c.

An ideal battery is a voltage source that delivers a constant voltage regardless of the load resistance or current drawn from it.

An ideal battery can maintain a steady voltage regardless of the amount of current being drawn from it.

In real-life batteries, there is always some internal resistance, which causes the voltage to drop as the current increases.

A resistor is an electrical component that opposes or limits the flow of electrical current. It has two terminals and can be made of various materials like carbon, metal, and ceramic. It is used in various applications, including voltage dividers, current limiting, and biasing.

A capacitor is an electronic component that stores energy in an electric field between two charged conductors. It has two terminals and is made of two conducting plates separated by an insulating material called a dielectric.

Capacitors are used in various applications, including energy storage, timing circuits, and power conditioning.

To Learn more :

https://brainly.com/question/17134302

#SPJ11

The statement "pry on the power steering reservoir to adjust the tension of the power steering belt" is: false.

The tension of the power steering belt is adjusted by adjusting the position of the power steering pump. There is a tension adjustment bolt on the power steering pump that is used to adjust the tension of the power steering belt. The adjustment bolt should be turned clockwise or counterclockwise to adjust the tension of the belt.

A belt tension gauge may be used to ensure that the belt is properly tensioned. A pry bar should not be used on the power steering reservoir to adjust the tension of the power steering belt. This could cause damage to the reservoir or other components of the power steering system. The reservoir should be inspected for damage or leaks, but it should not be used to adjust the tension of the belt.

In summary, the tension of the power steering belt should be adjusted by adjusting the position of the power steering pump, not by prying on the power steering reservoir.

To know more about tension refer here:

https://brainly.com/question/29869473#

#SPJ11

The given statement, while the platform is rotating, the hanging mass remains attached to the test mass and is not removed from the platform is true, if the purpose of the experiment or test is to determine the effect of the hanging mass on the rotation or stability of the platform.

In this case, the hanging mass must remain attached to the test mass during the rotation to observe the behavior of the system under the specified conditions. If the purpose of the experiment or test is to study the effect of the hanging mass on the platform's rotation or stability, the hanging mass must remain attached to the test mass during the rotation. This is because the presence of the hanging mass affects the overall weight and center of gravity of the system. Removing the hanging mass would alter the system's behavior and prevent accurate observations of the phenomenon under investigation. Therefore, if the experiment requires the hanging mass to be present, it must remain attached to the test mass while the platform is rotating.

To know more about platform, here

brainly.com/question/22850608

#SPJ4

--The complete question is, While the platform is rotating, the hanging mass remains attached to the test mass and is not removed from the platform. State true/false.--

Explanation:

To solve this problem, we can use the law of conservation of momentum, which states that the total momentum of a system is conserved in the absence of external forces.

Before the collision, the momentum of the blue clay is:

momentum of blue clay = mass of blue clay * velocity of blue clay

= 2 kg * 1.5 m/s = 3 kg*m/s to the east (positive)

Before the collision, the momentum of the red clay is:

momentum of red clay = mass of red clay * velocity of red clay

= 1.5 kg * (-2.5 m/s) = -3.75 kg*m/s to the west (negative)

The total momentum before the collision is:

total momentum before collision = momentum of blue clay + momentum of red clay

= 3 kgm/s - 3.75 kgm/s = -0.75 kg*m/s to the west (negative)

After the collision, the two clays stick together and move as one combined object. Let's assume that the final velocity of the combined clay pieces after the collision is v.

By the law of conservation of momentum, the total momentum after the collision is equal to the total momentum before the collision:

total momentum after collision = total momentum before collision

= -0.75 kg*m/s

The combined mass of the two clays after the collision is:

combined mass = mass of blue clay + mass of red clay

= 2 kg + 1.5 kg = 3.5 kg

Therefore, the final velocity of the combined clay pieces after the collision is:

v = total momentum after collision / combined mass

= (-0.75 kg*m/s) / 3.5 kg

= -0.214 m/s to the west (negative)

Since the negative velocity indicates a direction to the west, the final velocity of the combined clay pieces after the collision is 0.214 m/s to the west.

However, in general, acid rain is formed when sulphur dioxide (SO2) and nitrogen oxides (NOx) are emitted into the atmosphere by human activities, such as burning fossil fuels.

The erroneous statement among the following is : Acid rain is largely because to oxides of nitrogen and sulphur The greenhouse effect is to blame for the world's warming. Infrared radiation from the sun cannot reach earth due to the ozone layer.

Nitric and sulphuric acids are created when the gases nitrogen oxides and sulphur dioxide interact with the minute droplets of water in clouds. The rain from these clouds falls as very weak acid known as 'Acid rain'.

To know more about radiation visit:-

https://brainly.com/question/28202771

#SPJ1

Question:

"Which two of the following statements are true about the chemical reaction that forms acid rain?

a. Sulfur dioxide and nitrogen oxides react with water to form sulfuric acid and nitric acid.

b. Acid rain can cause damage to buildings and statues made of limestone or marble.

c. Acid rain is only a problem in areas with a high population density.

d. Acid rain has no effect on freshwater ecosystems."

The box will slide a distance of 6.96 m before coming to a stop due to the force of kinetic friction.

To determine how far the box will slide on the floor after it is given a push with an initial speed of 3.8 m/s, we need to use the equations of motion for constant acceleration. The force of kinetic friction acting on the box will cause it to decelerate, eventually coming to a stop.

The distance traveled by the box can be found using the equation:

d = [tex](v_i^2 - v_f^2) / (2 * a)[/tex]

where d is the distance traveled, v_i is the initial speed, v_f is the final speed (which is zero since the box comes to a stop), and a is the deceleration caused by the force of kinetic friction.

The deceleration can be found using the equation:

a = -F[tex]_friction / m[/tex]

where Ffriction is the force of kinetic friction and m is the mass of the box.

Assuming a mass of 5 kg for the box and a coefficient of kinetic friction of 0.11, the force of kinetic friction can be found using the equation:

F_friction = friction coefficient * F_normal

where F_normal is the normal force (equal to the weight of the box) and the friction coefficient is a dimensionless quantity that depends on the nature of the contact surface.

The weight of the box is:

Fweight = m * g

where g is the acceleration due to gravity (9.81 m/s²).

Therefore, the force of kinetic friction is:

F_friction = (0.11) * (5 kg * 9.81 m/s²) = 5.40 N

Using the equation for deceleration, we get:

a = -Ffriction / m = -(5.40 N) / (5 kg) = -1.08 m/s²

Finally, we can use the equation for distance traveled to find the distance the box will slide:

d = [tex](v_i^2 - v_f^2) / (2 * a)[/tex] =[tex](3.8 m/s)^2 / (2 * 1.08 m/s^2)[/tex] = 6.96 m

Learn more about kinetic: https://brainly.com/question/26472013

#SPJ11

The equivalent capacitance of a 6 mF capacitor, a 10 mF capacitor, and a 16 mF capacitor connected in parallel is: 32 mF

This is because when capacitors are connected in parallel, their total capacitance is equal to the sum of their individual capacitances. The formula for calculating the equivalent capacitance (C) of capacitors connected in parallel is: C = C1 + C2 + C3 + ... In this example, C = 6 mF + 10 mF + 16 mF = 32 mF.

Capacitors are electrical components that store energy in the form of an electric field between two conductors (plates). When capacitors are connected in parallel, the electric field between the plates of each capacitor is the same, but the overall capacitance is increased due to the combined plate area of all the capacitors.

This increase in plate area is why the equivalent capacitance of the three capacitors in this example is 32 mF, which is larger than any of the individual capacitances.

To know more about capacitors refer here:

https://brainly.com/question/17176550#

#SPJ11

The magnitude of the force that Alice is applying to the box is 110 N.

To calculate the force that Alice is applying, we need to use the equation F = ma. In this equation, F is the force applied, m is the mass of the box, and a is the acceleration of the box.

Since Alice is pushing the box at a constant speed of 2.8 m/s, the acceleration is 0, and the equation simplifies to F = 0 x m. Since the force must equal 0 when the acceleration is 0, the magnitude of the force that Alice is applying to the box is 0.

However, since Bob is pushing an identical box across the floor at a constant speed of 1.4 m/s, the acceleration is 0 and the equation simplifies to F = m x a. In this case, a is the acceleration of the box, which is 1.4 m/s.

Since we know that the magnitude of the force Bob is applying is 55 N, we can use the equation to calculate the force Alice is applying. 55 N = m x 1.4 m/s, which simplifies to m = 39.286.

We then substitute m back into the equation F = ma, so F = 39.286 x 1.4 m/s. This simplifies to F = 55.0 N, so the magnitude of the force Alice is applying is 55.0 N.

To know more about constant speed click on below link:

https://brainly.com/question/30151073#

#SPJ11

The formula for the impulse exerted on the ball from the instant it is dropped to an arbitrary time later is:

Impulse = (Final momentum - Initial momentum)

Impulse is a vector quantity having both magnitude and direction, whereas momentum is a vector quantity, but the impulse is not equal to momentum. The impulse is the change in momentum.

If a ball of mass m is dropped from rest, then its initial momentum is zero.

The final momentum of the ball after falling for time t is:

Final momentum = mv

Where v is the velocity of the ball after falling for time t.

Therefore, the impulse exerted on the ball from the instant it is dropped to an arbitrary time later is:

Impulse = (mv - 0) = mv

To know more about impulse:

https://brainly.com/question/14073258

#SPJ11

The spring is compressed by 0.70 m.

The 67.97 kg student standing atop a spring in an elevator that is accelerating upward at 3.66 m/s2 has a spring constant of 2658 n/m. The amount the spring is compressed can be calculated using the formula:

F = kx,

where F is the force, k is the spring constant, and x is the amount of compression.

Therefore, we can calculate the amount of compression in the spring as follows:

x = F/k = (67.97 kg * 3.66 m/s2)/2658 N/m = 0.70 m

Therefore, the spring is compressed by 0.70 m.

To know more about Spring compression, refer here:

https://brainly.com/question/12278394#

#SPJ11

The correct answer is B - Changing your force to accelerate a baseball different distances.

Newton's second law of motion is also called the law of acceleration. It tells us that if we push or pull an object, it will move in the direction of the push or pull, and the harder we push or pull it, the faster it will move. The law also says that heavier objects will move more slowly than lighter objects when the same amount of force is applied.

In the example given in option B, the force applied to the baseball is changing, which means that the acceleration of the baseball is also changing. This is a clear demonstration of the law of acceleration. Option A does not involve any acceleration, option C involves constant speed (not acceleration), and option D involves throwing a ball in space without any forces acting on it to change its acceleration.

Answer:

The relative density of the liquid is 1.5

Explanation:

The relative density of a liquid is defined as the ratio of the density of the liquid to the density of water. We can use the principle of buoyancy to find the relative density of the liquid.

When the body is immersed in water, it experiences an upthrust equal to the weight of water displaced. Therefore, the weight of water displaced = weight of the body in air - weight of the body in water = 0.5 kg - 0.3 kg = 0.2 kg.

Similarly, when the body is immersed in the liquid, it experiences an upthrust equal to the weight of liquid displaced. Therefore, the weight of liquid displaced = weight of the body in air - weight of the body in the liquid = 0.5 kg - 0.2 kg = 0.3 kg.

The relative density of the liquid can be found as follows,

Relative density of liquid = Density of liquid / Density of water

= (Weight of liquid displaced / Volume of liquid) / (Weight of water displaced / Volume of water)

= (0.3 kg / Volume of liquid) / (0.2 kg / Volume of water)

= (0.3 kg / Volume of liquid) / (0.2 kg / 0.2 L) [since the density of water is 1 g/mL or 1 kg/L]

= 1.5 / Volume of liquid

Therefore, the relative density of the liquid is 1.5 divided by the volume of the liquid in liters.

D) introduce a dielectric material between the plates, and E) decrease the separation between the plates will increase the capacitance of a parallel-plate capacitor.

The capacitance of a parallel-plate capacitor is given by the formula:

C = εA/d

where C is the capacitance, ε is the permittivity of free space, A is the area of the plates, and d is the distance between the plates.

From this formula, we can see that the capacitance is directly proportional to the area of the plates and the permittivity of free space, and inversely proportional to the distance between the plates. Therefore, the following changes will increase the capacitance of a parallel-plate capacitor:

D) Introduce a dielectric material between the plates: A dielectric material has a higher permittivity than air, which increases the capacitance of the capacitor.

E) Decrease the separation between the plates: A decrease in the distance between the plates increases the capacitance of the capacitor.

Therefore, the correct choices are D) introduce a dielectric material between the plates, and E) decrease the separation between the plates.

Learn more about Capacitor: https://brainly.com/question/17176550

#SPJ11

Answer: the answer given below

(a) Explanation: The impulse on an object is given by the change in momentum of the object. Before the collision, the bullet has momentum p1 = mv0 and the brick has momentum p2 = 0, since it is stationary. After the collision, the combined bullet-brick system has momentum p3.

Conservation of momentum requires that the total momentum before the collision is equal to the total momentum after the collision:

p1 + p2 = p3

mv0 + 0 = (m + M)V

where V is the velocity of the combined bullet-brick system after the collision. Solving for V, we get:

V = (mv0) / (m + M)

The impulse on the bullet during the collision is equal to the change in momentum of the bullet:

J_bullet = p3 - p1 = (m + M)V - mv0

Substituting the expression for V we found earlier:

J_bullet = (m + M)(mv0) / (m + M) - mv0 = 0

Therefore, the impulse on the bullet is zero during the collision.

On the other hand, the impulse on the brick during the collision is:

J_brick = p3 - p2 = (m + M)V - 0 = (m + M)(mv0) / (m + M) = mv0

Therefore, the magnitude of the impulse acting on the brick is equal to the initial momentum of the bullet, mv0, and it is in the same direction as the initial velocity of the bullet.

In summary, during the collision of the bullet and the brick, the impulse acting on the bullet is zero, while the impulse acting on the brick is mv0 in the direction of the initial velocity of the bullet.

(b) We can use the principle of conservation of momentum to solve for the velocity of the brick-bullet combination just after the collision. The total momentum of the system (bullet, brick, and Earth) is conserved before and after the collision. Initially, only the bullet has momentum, which is given by p1 = m*v0, and the momentum of the brick and Earth is zero. After the collision, the bullet becomes embedded in the brick, and the combined system of the brick-bullet has momentum p2. Since the momentum of the Earth is negligible compared to that of the bullet and brick, we can treat the system as closed and apply conservation of momentum:

p1 = p2

m*v0 = (M + m)*v

where v is the velocity of the combined system just after the collision.

Solving for v, we get:

v = (m*v0) / (M + m)

Therefore, the magnitude of the velocity of the brick-bullet combination just after the collision is:

|v| = |(m*v0) / (M + m)|

The direction of the velocity is upward, as the system swings up after the collision due to the conservation of momentum.

(c) The initial kinetic energy of the system is the kinetic energy of the bullet just before the collision, which is given by:

KE1 = (1/2)mv0^2

The final kinetic energy of the system is the kinetic energy of the combined brick-bullet system just after the collision, which is given by:

KE2 = (1/2)*(M + m)*v^2

Substituting the expression we found for v:

KE2 = (1/2)(M + m)[(mv0) / (M + m)]^2

KE2 = (1/2)(m*v0^2) / (1 + M/m)

The ratio of the final kinetic energy to the initial kinetic energy is:

KE2 / KE1 = [(1/2)(mv0^2) / (1 + M/m)] / [(1/2)mv0^2]

KE2 / KE1 = 1 / (1 + M/m)

Therefore, the ratio of the final kinetic energy of the brick-bullet combination immediately after the collision to the initial kinetic energy of the brick-bullet combination is:

KE2 / KE1 = 1 / (1 + M/m)

(d)To determine the maximum vertical position reached by the brick-bullet combination, we can use conservation of energy, assuming there is no energy loss due to friction or other dissipative forces. At the maximum height, the kinetic energy of the system is zero, and all the initial kinetic energy has been converted to potential energy due to the height above the initial position.

The initial total energy of the system is the sum of the initial kinetic energy of the bullet and the gravitational potential energy of the brick:

E1 = (1/2)mv0^2 + Mgh1

where h1 is the initial height of the brick above the ground, and g is the acceleration due to gravity.

At the maximum height, the final total energy of the system is the potential energy due to the height above the ground:

E2 = (M + m)gh2

where h2 is the maximum height reached by the brick-bullet combination above the initial position.

Since there is no energy loss, we can set the initial energy equal to the final energy:

E1 = E2

Substituting the expressions for E1 and E2 and solving for h2, we get:

(M + m)gh2 = (1/2)mv0^2 + Mgh1

h2 = [(1/2)mv0^2 + Mgh1] / [(M + m)*g]

Simplifying, we get:

h2 = (1/2)v0^2 / g + h1(M/m) / (1 + M/m)

Therefore, the maximum vertical position above the initial position reached by the brick-bullet combination is:

h2 = (1/2)v0^2 / g + h1(M/m) / (1 + M/m)

Hope this helps :)

a. The angular acceleration of the wheels is 0.2945 rad/s². b. The angular velocity of the wheels after 8 seconds is 2.3560 rad/s.

Calculation:

a. The formula for angular acceleration is: α = (ω2 - ω1) / (t2 - t1) Whereα is angular acceleration, ω2 is final angular velocity, ω1 is initial angular velocity, t2 is final time, t1 is initial time. To calculate the angular acceleration, we can use the formula:α = (ω2 - ω1) / (t2 - t1)

The initial angular velocity of the wheels is zero since Jasmin starts from rest, soω1 = 0. We know that the wheels make 3 revolutions after 8 seconds, so the final angular velocity can be calculated as follows: ω2 = (3 revolutions / 8 s) x (2π radians / 1 revolution) = 2.3562 rad/s

Therefore,α = (2.3562 rad/s - 0 rad/s) / (8 s - 0 s) = 0.2945 rad/s². The angular acceleration of the wheels is 0.2945 rad/s².

b. To calculate the angular velocity of the wheels after 8 seconds, we can use the formula:ω = ω1 + αtWhereω is angular velocity,ω1 is initial angular velocity,α is angular acceleration, t is time. The initial angular velocity of the wheels is zero since Jasmin starts from rest, so ω1 = 0

We have already calculated the angular acceleration to be 0.2945 rad/s², and we know that the time is 8 seconds, soω = ω1 + αt = 0 + (0.2945 rad/s²) x (8 s) = 2.3560 rad/s. Therefore, the angular velocity of the wheels after 8 seconds is 2.3560 rad/s.

To know more about angular acceleration, refer here:

https://brainly.com/question/29428475#

#SPJ11

The given statement "centripetal force in a collapsing cloud of gas and dust is strongest at the poles" is - True.

Centripetal force refers to a force that drives an object toward a fixed point, which is the center of a circular path. For example, if you tie a ball to a string and whirl it around in a circle, the string exerts a centripetal force on the ball that keeps it moving in a circle.

The force of gravity is the most common centripetal force that we encounter in nature, and it is what drives the movement of planets, moons, and other celestial objects.

During the formation of a star, a cloud of gas and dust collapses inwards due to gravity. The cloud starts to rotate as it shrinks due to the law of conservation of momentum. The centripetal force in this situation is the gravitational force that holds the cloud together.

The gravitational force, on the other hand, is stronger at the poles of the cloud. The gravitational force increases as the distance between the particles in the cloud decreases. Because the poles of the cloud are closer together, the gravitational force is stronger, and the centripetal force is also stronger.

As a result, the centripetal force in a collapsing cloud of gas and dust is strongest at the poles.

To know more about centripetal force click here:

https://brainly.com/question/14249440

#SPJ11

The location of her centre of mass, a physics student lies on a lightweight plank supported by two scales 2.50m apart, as indicated in the figure. If the left scale reads 290 N and the right scale reads 112 N The student's mass is approximately 41 kg, and the distance from her head to her centre of mass is approximately 0.696 m.

To determine the student's mass, we can sum up the readings from both scales, which are measures of force (Newtons) and then convert it to mass using the gravitational acceleration (g = 9.81 m/s²).
Step 1: Calculate the total force acting on the plank:
Total Force = Force_left_scale + Force_right_scale
Total Force = 290 N + 112 N
Total Force = 402 N
Step 2: Convert the total force to mass using gravitational acceleration:
Mass = Total Force / g
Mass = 402 N / 9.81 m/s²
Mass ≈ 41 kg
Now, to find the distance from the student's head to her centre of mass, we'll use the principle of torque equilibrium.
Step 3: Set up the torque equation:
Torque_left_scale = Torque_right_scale
Force_left_scale × Distance_left_scale = Force_right_scale × Distance_right_scale
Let x be the distance from the student's head to her centre of mass. Then, the distance from the left scale to the centre of mass is x, and the distance from the right scale to the centre of mass is (2.50 - x).
Step 4: Plug in the known values and solve for x:
290 N × x = 112 N × (2.50 - x)
Step 5: Simplify the equation and solve for x:
290x = 112(2.50) - 112x
290x + 112x = 112(2.50)
402x = 280
x ≈ 0.696 m
The student's mass is approximately 41 kg, and the distance from her head to her centre of mass is approximately 0.696 m.

For more such questions on  centre of mass

brainly.com/question/28021242

#SPJ11

The current I(r) at a time after 1*r equals the time constant r is roughly 0.065 A. About 0.105 A is the current I(3r) at a point three times the time constant after 3*r.

Electric current (I) flowing through a circuit directly relates to its potential difference (V). When the potential difference is 60 volts, the electric current is 1.5 amps.

The following equations can be used to calculate the current in the RL circuit based on the information provided:

An RL circuit's current is determined by:

I(t) = (V/R) * (1 - e(-t/r))

The following queries can be resolved using this equation:

Question 1:

Add t = r to the equation as follows:

I(r) = (V/R) * (1 - e(-r/r))

I(r) = (V/R) * (1 - e(-1))

I(r) = (12.0/150) * (1 - e(-1))

I(r) ≈ 0.065 A

As a result, the current I(r) at a time after 1*r equals the time constant r is approximately 0.065 A.

Question 2:

What time is it now, I(3r), after 3*r, which is three times the time constant?

In the following equation, substitute t = 3r:

I(3r) = (V/R) * (1 - e(-3))

I(3r) = (12.0/150) * (1 - e(-3))

I(3r) ≈ 0.105 A

As a result, the current I(3r) at a time three times the time constant after 3*r is about 0.105 A.

Question 3:

After some time, the circuit's current will begin to approach a constant value, I. (as t tends to infinity). Who am I?

The exponential term e(-t/r) approaches 0 as t approaches infinity, and the current becomes:

I∞ = V/R

Substitute V = 12.0 V and R = 150 Ω into the equation:

I∞ = 12.0/150

I∞ = 0.08 A

As a result, after some time, the circuit's current will stabilize around 0.08 A.

To know more about current visit:-

https://brainly.com/question/15632994

#SPJ1

Question:

After the switch is closed, the current in the circuit grows over time approaching a constant value. In general, at time after a voltage source is connected to an RL circuit, the current I(t) in the circuit is given by the expression

1(t)=(1-e); where r = L/R

where & is the voltage provided by the battery, R is the resistance of the resistor, and r is the time constant characteristic of the circuit.

Growth of current in an RL circuit

Consider an R-L circuit as shown in the figure. The battery provides 12.0 V of voltage. The inductor has inductance L, and the resistor has resistance R = 150 . The switch is initially open as shown. At time r=0, the switch is closed. At time / after 0 the current /(1) flows through the circuit as indicated in the figure.

Question 1:

What is the current (r) at a time after 1-0 equal to time constant?

Question 2:

What is the current /(3r) at a time after 1-0 equal to three times the time constant?

Question 3:

The current in the circuit will approach a constant value / after a long time (as / tends to infinity). What is I.?

The water molecules require more energy to be further separated and converted into steam than it does to convert ice to liquid water, because liquid water has a higher specific heat capacity than ice, which means that it requires more energy to raise its temperature.

In order to convert liquid water into steam, the water molecules must absorb a large amount of energy. This energy is used to overcome the strong intermolecular forces of attraction between the water molecules that hold them in their liquid state. This energy is known as the latent heat of vaporization.

In contrast, when ice is converted into liquid water, the energy required is only enough to overcome the weaker intermolecular forces of attraction that hold the ice in its solid state. This energy is known as the latent heat of fusion.

Once the ice has been converted to liquid water, the water molecules require more energy to be further separated and converted into steam than they did to overcome the weaker forces that held them together as a solid ice block. This is because liquid water has a higher specific heat capacity than ice, which means that it requires more energy to raise its temperature.

Learn more about latent heat of vaporization here:

https://brainly.com/question/30762921#


#SPJ11

The material that should be used on a bicycle ramp to increase friction is option b) rough paper.

Rough paper has a large number of tiny, unevenly-shaped fibers which create a large amount of friction. This makes it ideal for bike ramps as it helps to slow and control the speed of a bicycle while they travel on the ramp. Additionally, rough paper is lightweight and easy to work with, making it ideal for creating ramps.

To ensure the best results, you should use thick, high-quality paper with a large number of tiny fibers. This will create more friction, allowing for better control and more stability for the cyclist. Additionally, you should ensure that the paper is securely attached to the ramp so that it doesn’t slip or move while the cyclist is on the ramp.

Overall, the best material to use on a bicycle ramp to increase friction is rough paper. Its numerous tiny fibers provide plenty of friction, while its lightweight and easy installation make it ideal for bike ramps. With the right paper and installation, you can ensure that cyclists have the best experience possible when using your ramp.

Therefore, the best material to use on a bicycle ramp to increase friction is rough paper.

To know more about friction, refer here:

https://brainly.com/question/13000653#

#SPJ11

1 - Since electrοns can be transferred frοm οur hair tο the ballοοn , electrοns cannοt be transferred frοm ballοοn tο οur hair because. This is an illustratiοn οf  charging by cοnductiοn.

2 - Since the rubber οn the ballοοn is significantly less cοnductive than the hair, electrοns will nοt easily escape the ballοοn because οf this.

3 - Neutrοns are electrically neutral , neutrοns dοesn't participate in this prοcess.

A charged οbject must cοme intο cοntact with a neutral οbject tο cοnduct electricity. As a result, when twο charged cοnductοrs cοme intο cοntact, the charge is split between the twο cοnductοrs, charging the uncharged cοnductοr.

When twο neutral οbjects are rubbed against οne anοther, electrοns are transferred. The οbject that has a strοnger affinity fοr electrοns will take electrοns frοm the οther οbject, and the twο becοme charged in οppοsitiοn. In this instance, the electrοns frοm the hair are taken up by the ballοοn , which nοw has an excess οf electrοns and a negative charge cοmpared tο the hair's current electrοn shοrtage and pοsitive charge.

2- Since the rubber οn the ballοοn is significantly less cοnductive than the hair, electrοns will nοt easily escape the ballοοn because οf this.

3- Neutrοns are electrically neutral , neutrοns dοesn't participate in this prοcess.

4-Insulating materials may becοme electrically charged when they cοme intο cοntact with οne anοther. Negatively charged electrοns can "rub οff" οne material and "rub οn" tο anοther. After bοth things have the same quantity οf οppοsite charges, the substance that gets electrοns becοmes negatively charged, and the material that lοses electrοns becοmes pοsitively charged.

To know more about charging by conduction , visit;

brainly.com/question/10254645

#SPJ1

According to Newton's first law, an unbelted victim in a car accident will continue to move in the same direction and with the same speed until the dashboard causes a change in motion.

Inertia is the tendency of an object to remain in motion in the absence of an unbalanced force. It is the property of an object to resist any change in motion unless acted upon by an external force.

The dashboard applies an external force that changes the direction and speed of the victim. This is because the person has no external forces acting on them to cause them to stop. Since they were in motion at the time of the accident, they will continue in that motion unless acted upon by another force, such as the dashboard, until they come to a stop or another force acts upon them.

Therefore, the best exemplifies the law of inertia. The law of inertia states that an object at rest will remain at rest, and an object in motion will remain in motion at a constant velocity unless acted upon by an external unbalanced force.

Learn more about the speed at

brainly.com/question/24091038

#SPJ11

When standing on a scale in an elevator, if one notices an increase in their weight, it means that: the elevator is accelerating upwards.

This is due to the fact that the scale underfoot has to counter the upward acceleration of the elevator, which causes the weight measured on the scale to increase. The scale measures the normal force, which is the weight being exerted on the scale, which is equal to the mass of the individual multiplied by the gravitational acceleration on the surface of the earth.

This can be represented by the formula: W = mg,

where W is the weight, m is the mass of the object and g is the gravitational acceleration.

When the elevator is stationary or moving at a constant velocity, the gravitational acceleration is the same as the normal force and the weight of the individual remains constant. However, when the elevator begins to accelerate upwards, the normal force exerted by the scale must increase to counter the upward acceleration of the elevator.

This causes an increase in weight measured on the scale. Therefore, if one notices an increase in their weight while standing on a scale in an elevator, it indicates that the elevator is accelerating upwards.

To know more about acceleration refer here:

https://brainly.com/question/30660316#

#SPJ11

The net force on a 30.0 nc charge located at the origin by two other charges is the vector sum of the forces exerted by the two other charges. The force exerted by the first charge, -50.0 nC located at (-5.0 m, 2.0 m), is given by:

F1 = (k*q1*q2)/r2, where

Therefore,

F1 = (8.99 x 109 N m2/C2)*(-50.0 nc)*(30.0 nc)/(5.3852) = 2.38 x 10-2 N

Similarly, the force exerted by the second charge, 40.0 nc located at (3.0 m, 1.0 m), is given by:

F2 = (k*q1*q2)/r2, where

Therefore,

F2 = (8.99 x 109 N m2/C2)*(40.0 nc)*(30.0 nc)/(3.1622) = 4.58 x 10-2 N

The net force is the vector sum of F1 and F2 and can be calculated as follows:

F net = F1 + F2 = 2.38 x 10-2 N + 4.58 x 10-2 N = 7.00 x 10-2 N

Therefore, the net force on a 30.0 nc charge located at the origin by two other charges is 7.00 x 10-2 N.

To know more about Force refer here:

https://brainly.com/question/13191643#

#SPJ11

Answer: The rock's speed as it left your hand was 8.8 m/s.

Explanation: The system is the rock and the Earth. The initial state is the rock at rest in your hand 2.8 m below the Frisbee. The final state is the rock hitting the Frisbee at a speed of 4.0 m/s.

Using conservation of energy, we know that the initial potential energy of the rock-Earth system is transformed into both kinetic energy and potential energy at its maximum height. Therefore, we can use the conservation of energy equation:

potential energy (initial) = kinetic energy (final) + potential energy (final)

mgh = 1/2mv^2 + mgh

where m is the mass of the rock, g is the acceleration due to gravity, h is the height that the rock has been raised, and v is the velocity of the rock.

We can solve for the initial velocity by rearranging the equation:

v = sqrt(2gh + v^2)

Plugging in the values, we get:

v = sqrt(2 * 9.81 * 2.8 + 4^2)

v ≈ 8.8 m/s

Therefore, the rock's speed as it left your hand was 8.8 m/s.

When you hold a box of books with flat hands and press harder, the friction force applied by your hands onto the sides of the box will increase.

The force causes motion because if an object is at rest, it remains at rest until acted upon by a force. If the object is in motion, it remains in motion unless acted upon by a force to slow it down, speed it up, or change its direction. So, we have to look at the direction of the force and the motion to understand how the force will affect it. In general, the frictional force opposes motion.

The force of friction is proportional to the force pressing the two surfaces together. In this case, the force pressing the box onto your hands will be greater if you press harder, resulting in a greater frictional force applied by your hands onto the sides of the box, according to Coulomb's laws. Therefore, the friction force will increase when you press harder.

Learn more about friction force at https://brainly.com/question/15122221

#SPJ11

The resultant force of the water on the semi-circular gate on an inclined wall can be calculated using the equations of hydrostatics.

R = √([tex]F1^2 + F2^2 - 2*F1*F2*cos[/tex])α, where 'R' is the resultant force and 'α' is the angle of the wall.

First, determine the pressure of the water at any given point along the gate. To do this, multiply the density of the water, 'ρ', by the acceleration of gravity, 'g', and then the vertical height of the water relative to the gate, 'h', to get the pressure 'p':

p = ρ*g*h

Second, determine the force acting on the gate. This is done by multiplying the pressure with the area of the gate, 'A':

F = p*A

Finally, find the resultant force, 'R', by adding the forces together and taking into account the angle of the wall:

R = √([tex]F1^2 + F2^2 - 2*F1*F2*cos[/tex])α

where α is the angle of the wall.

By following these steps, you can calculate the resultant force of the water on the semi-circular gate on an inclined wall.

For more questions related to Force.

https://brainly.com/question/13191643

#SPJ11