The pen's narrow end provides a small surface area for it to balance on, making it more difficult to stay upright.
Balancing a pen verticallyThis is because the pen is not symmetrical and has a wide top compared to the bottom. The wider top will cause the pen to easily tip over when placed on its narrow end due to the unbalanced weight distribution.
Balancing a pen vertically on its narrow end also requires a steady hand and a great deal of focus. The pen must be held perfectly still and be placed gently in order to maintain its balance. If the pen is shifted even slightly, it can easily fall off of its narrow end. Additionally, the surface the pen is placed on must be even and stable to provide a solid base for it to balance on.
Learn more about center of gravity here:
https://brainly.com/question/24553858
#SPJ1
A bar magnet is falling through a loop of wire with constant velocity. The north pole enters first. As the south pole
leaves the loop of wire, the induced current (as viewed from above) will be in which direction?
a) is counterclockwise.
b) is along the length of the magnet
c) is zero
d) is clockwise
As the south pole leaves the loop of wire, the induced current (as viewed from above) will be in the clockwise direction.
Whenever a magnet is moved near a closed circuit or wire loop, an emf (electromotive force) is generated in the conductor. When the magnet moves in and out of the coil or loop, the magnitude and direction of this voltage changes, generating an induced current. This is referred to as Faraday's law of electromagnetic induction, which states that an emf is induced in a closed conductor when the magnetic flux through the surface enclosed by the conductor changes over time.
To know more about magnet click on below link :
https://brainly.com/question/2841288#
#SPJ11
a 7.50g-bullet has a speed of 555 m/s as it leaves the muzzle of a rifle. if the barrel of the rifle is 0.950 m, what is the average force exerted on the bullet by the ammunition?
The average force exerted on the bullet by the ammunition is 2434.2 N.
We can use the impulse-momentum theorem to determine the average force exerted on the bullet by the ammunition:
[tex]F_{avg} \times t = \Delta p[/tex]
where F_avg is the average force, t is the time over which the force is applied, and Δp is the change in momentum of the bullet. Since the bullet is fired from the muzzle of the rifle, we can assume that the time over which the force is applied is equal to the time it takes for the bullet to travel the length of the barrel:
t = L / v
where L is the length of the barrel and v is the velocity of the bullet.
Substituting L = 0.950 m and v = 555 m/s, we get:
t = 0.950 m / 555 m/s = 0.00171 s
The change in momentum of the bullet can be calculated as:
[tex]\Delta p = p_f - p_i[/tex]
where p_f is the final momentum of the bullet and p_i is its initial momentum. Since the bullet is fired from rest, its initial momentum is zero. The final momentum can be calculated using the formula:
p_f = m * v
where m is the mass of the bullet and v is its velocity. Substituting
m = 7.50 g = 0.00750 kg and v = 555 m/s, we get:
[tex]p_f = 0.00750 kg \times 555 \ m/s = 4.16\ kg m/s[/tex]
Therefore, the change in momentum of the bullet is:
[tex]\Delta p = p_f - p_i = 4.16\ kg m/s - 0 = 4.16 \ kg m/s[/tex]
Substituting t = 0.00171 s and Δp = 4.16 kg m/s into the expression for the average force, we get:
[tex]F_{avg} \times t = \Delta p[/tex]
[tex]F_{avg} = \Delta p / t = (4.16\ kg m/s) / (0.00171 s) = 2434.2\ N[/tex]
Therefore, the average force exerted on the bullet is 2434.3 N.
Learn more about force:
https://brainly.com/question/12785175
#SPJ11
Which type of engine has a wheel with several blades mounted on a shaft that rotate a shaft when hit with heated air at a high velocity?
The type of engine that has a wheel with several blades mounted on a shaft that rotates when hit with heated air at a high velocity is called a gas turbine engine.
What is a gas turbine engine?
The gas turbine engine is also known as a combustion turbine engine. A gas turbine engine is a type of internal combustion engine that converts the chemical energy of fuel into mechanical energy, which can be used to power various machines and equipment. The engine works by compressing air and then mixing it with fuel in a combustion chamber, where it is ignited to produce a high-temperature, high-pressure gas stream. This gas stream then flows through a series of turbine blades, causing them to spin, which drives a shaft that is connected to various machines or equipment. As the shaft rotates, it generates mechanical power that can be used for various applications.
Gas turbine engines are commonly used in aircraft, power plants, and marine propulsion.
To learn more about gas turbine engines, visit:
https://brainly.com/question/7324077
#SPJ1
A skydiver of mass 95kg ,before opening his parachute, falls at t1 with V1= 11m/s and at t2 with t2 v2=27m/s; supposing friction is zero, find the distance covered between t1 and t2
The skydiver covered a distance of approximately 94.9 meters before opening his parachute between t1 and t2, assuming no air resistance or friction.
v = final velocity = v2 = 27 m/s
u = initial velocity = v1 = 11 m/s
a = acceleration = g = 9.8 m/[tex]s^2[/tex]
s = (v² - u²) / 2a
s = (27² - 11²) / (2 x 9.8) = 94.9 meters
Resistance measures an item's potential to impede the drift of electrical present-day through it. it's far measured in ohms (Ω). Resistance is decided by way of the bodily residences of an item, along with its dimensions, material, and temperature. while electric-powered present-day flows thru a conductor, it encounters resistance that slows down its float. This resistance is as a result of the collisions among electrons and the atoms inside the conductor.
Resistance can be laid low with changes inside the bodily properties of the conductor, such as duration, cross-sectional region, or temperature. an extended or narrower conductor may have higher resistance, even as a much broader conductor could have decreased resistance. understanding resistance is critical for designing and working electrical circuits. with the aid of controlling the resistance of a circuit, engineers can make sure that the appropriate amount of current flows to electricity the devices linked to it.
To know more about Resistance visit here:
brainly.com/question/11431009
#SPJ4
two stationary point charges q1 and q2 are shown in the figure along with a sketch of some field linesrepresenting the electric field produced by them. what can you deduce from the sketch?
From the sketch, we can deduce that the two charges q1 and q2 are of opposite signs, as field lines start at the positive charge q1 and end at the negative charge q2. The field lines also indicate that the magnitude of the electric field produced by q1 is larger than that of q2.
Additionally, the field lines show that the electric field lines near the charges are denser, indicating a stronger electric field intensity near the charges. The direction of the electric field points from q1 to q2, which is consistent with the direction of the force that a positive test charge would experience if placed in the field. The field lines also show that the electric field is radial, i.e., the field lines point directly away from or towards each charge in a straight line, which is a characteristic of the electric field produced by a point charge. Finally, the density of the field lines decreases with distance from the charges, indicating that the electric field strength decreases with distance from the charges, following an inverse-square law.Learn more about electric field at: https://brainly.com/question/14372859
#SPJ11
a hard billiard ball elastically collides with another hard billiard ball of equal mass. which situation is possible?
In an elastic collision, the total kinetic energy and momentum of the system are conserved. So, in the case of a hard billiard ball elastically colliding with another hard billiard ball of equal mass,
There are two possible situations that can occur. These situations are as follows:
When the two hard billiard balls collide head-on and return with equal speed.When the two hard billiard balls collide at an angle, they deflect at the same angle, and their speed remains the same.
Elasticity refers to the ability of a substance to return to its original shape and size when an external force is applied to it.
Elasticity is an essential concept in the field of physics and is used to describe the behavior of materials under stress.The coefficient of restitution is a measure of the elasticity of an object.
It is defined as the ratio of the relative speed of separation to the relative speed of approach after a collision between two objects.
The coefficient of restitution ranges from 0 to 1, with 0 representing a completely inelastic collision and 1 representing a completely elastic collision.
When two hard billiard balls elastically collide, they can either collide head-on and return with equal speed or collide at an angle and deflect at the same angle while maintaining the same speed.
Elasticity is a fundamental concept that is used to describe the behavior of materials under stress. The coefficient of restitution is a measure of the elasticity of an object.
to know more about elastic collision refer here:
https://brainly.com/question/12941951#
#SPJ11
old faithful geyser in yellowstone national park shoots water every hour to a height of 40.0 m. with what velocity does the water leave the ground?
The velocity with which the water leaves the ground is 28.0 m/s (downward).
The Old Faithful Geyser in Yellowstone National Park shoots water every hour to a height of 40.0 meters.
To find the velocity with which the water leaves the ground, we can use the following kinematic equation:
v² = u² + 2as
Here,
v = final velocity
u = initial velocity
a = acceleration due to gravity
s = distance traveled by the object
The initial velocity of the water when it leaves the ground is 0 m/s.
Also, we can assume the final velocity of the water when it reaches the maximum height to be 0 m/s.
We know that the acceleration due to gravity is -9.8 m/s² (negative due to the direction).
The distance traveled by the water is the height to which it rises, i.e., 40.0 meters.
Using the above values in the kinematic equation, we get:
v² = 0² + 2*(-9.8)*40.0v² = -784v = √(-784)
Since the answer is coming out to be negative, it indicates that the velocity is in the downward direction.
So, the velocity with which the water leaves the ground is 28.0 m/s (downward).
To know more about velocity, refer here:
https://brainly.com/question/30559316#
#SPJ11
when lighted, a 100-watt light bulb operating on a 110-volt household circuit has a resistance closest to
When lighted, a 100-watt light bulb operating on a 110-volt household circuit has a resistance closest to 0.99 ohms.
Resistance refers to the electrical property of a circuit component, such as a light bulb, that resists the flow of electrical current through it.
Ohm's law is a fundamental principle in electrical engineering that relates the resistance, voltage, and wattage in a circuit. It states that the resistance (R) is equal to the voltage (V) divided by the wattage (W).
W = 100 watts, V = 110 volts.
Use Ohm’s law to calculate the resistance (R):
R = V/W = 110/100 = 0.99 ohms.
Therefore, when a 100-watt light bulb is operating on a 110-volt household circuit, its resistance is approximately 0.99 ohms.
To know more about resistance click here:
https://brainly.com/question/11431009
#SPJ11
is the transfer of information between two or more points that are not connected by an electrical conductor?
Yes, the transfer of information between two or more points that are not connected by an electrical conductor is possible and is referred to as wireless communication.
Wireless communication involves the use of electromagnetic waves such as radio waves, microwaves, and infrared waves, to transmit data between two points without the need for physical contact or connection.
Wireless communication is used in various fields, such as broadcasting, radio communication, mobile communication, satellite communication, and Internet access. Wireless communication technology has revolutionized communication and enabled a wide range of applications, from wireless microphones to Wi-Fi networks, GPS tracking systems, Bluetooth connectivity, and cellular communication.
Wireless communication is an important component of the modern world and will continue to play a major role in the advancement of communication technology.
Therefore, the transfer of information between two or more points that are not connected by an electrical conductor is possible and is done through wireless communication.
To know more about wireless communication, refer here:
https://brainly.com/question/30490055#
#SPJ11
2. how many times a minute does a boat bob up and down on ocean waves that have a wavelength of 36.0 m and a propagation speed of 4.80 m/s?
The boat will bob up and down on ocean waves that have a wavelength of 36.0 m and a propagation speed of 4.80 m/s once every 7.50 seconds.
To solve the given question, we must use the formula:
n= v/f
Where: v is the velocity of the wave (in m/s)f is the frequency of the wave (in Hz)n is the number of cycles per second
Therefore, the frequency of the wave (in Hz) can be calculated by using the formula:
f= v/λ
where: v is the velocity of the wave (in m/s)λ is the wavelength of the wave (in m)
The frequency of the wave is 0.1333 Hz (approx).
Now, the number of cycles per second (n) is: n = v/λ
We can solve for n by dividing the velocity of the wave by the wavelength of the wave.
Therefore,
n= v/λ= (4.80 m/s) / (36.0 m)= 0.1333 Hz
So, the boat bob up and down 0.1333 times a minute on ocean waves that have a wavelength of 36.0 m and a propagation speed of 4.80 m/s.
1 Hz = 60 seconds,
0.1333 Hz = 7.50 seconds.
To know more about Frequency, refer here:
https://brainly.com/question/29739263#
#SPJ11
a car is traveling at 40 m/s as it enters a turn of radius 25 meters. what minimum coefficient of friction must be maintained between the road and tires to make sure the car does not slide out of the turn?
The minimum coefficient of friction required for a car travelling at 40 m/s to not slide out of a turn of radius 25 meters is 0.21.
This is determined using the equation for the maximum centripetal force that the car can withstand. This equation states that the maximum centripetal force is equal to the mass of the car times its speed squared divided by the radius of the turn multiplied by the coefficient of friction. Using this equation, 0.21 is the coefficient of friction that is required to make sure the car does not slide out of the turn.
The equation for maximum centripetal force can be written as:
F = m*v2/r * μ Where m is the mass of the car, v is the velocity of the car, r is the radius of the turn, and μ is the coefficient of friction.
Since we are solving for the coefficient of friction (μ), we can solve this equation for μ:
μ = m*v2/r * F
Plugging in the given values, we get:
μ = (1000 kg) * (40 m/s)2 / (25 m) * (10000 N) = 0.21
Therefore, the minimum coefficient of friction required for a car travelling at 40 m/s to not slide out of a turn of radius 25 meters is 0.21.
For more such questions on Coefficient of friction.
https://brainly.com/question/22696010#
#SPJ11
a van exerts a force on trailers of different masses m. compared with the force exerted on each trailer, rank the magnitude of force each trailer exerts on the van. (or are all pairs of forces equal in magnitude?)
The trailer pulls on the vehicle with an average force of A=B=C.
Newton's second law of acceleration is expressed as follows: F = ma
In this case, the mass is m, and the acceleration is a.
Assume that g=9.8 m/s2 represents the acceleration caused by gravity.
The acceleration of the object will be zero if it is travelling at a constant speed.
Because of the constant velocity, the van's net force on the trailer is therefore zero.
As a result, the van applies the same amount of force to each trailer. Thus, FA FB = FC.
As a result, each trailer pulls on the van with the same amount of force in the opposite direction. FA' = FB' = Fc', therefore.
As a result, A=B=C represents the rank of the force the trailer exerts on the van.
To know about force
https://brainly.com/question/24115409
#SPJ4
an n-type piece of silicon experiences an electric field equal to 0.1v/m. (a) calculate the velocity of electrons and holes in this material
In an n-type piece of silicon, the electric field causes the electrons to accelerate due to the attractive force between the negatively charged electrons and the positively charged electric field. This acceleration causes the electrons to reach a velocity of V = E/μ, where E is the electric field (0.1V/m) and μ is the mobility of electrons in silicon (1350 cm2/V⋅s). Therefore, the velocity of electrons in this material would be equal to 0.1V/m/1350cm2/V⋅s = 0.0741 cm/s.
The holes, on the other hand, experience a repulsive force due to the positive electric field. This causes the holes to decelerate, with a velocity of V = -E/μ. Therefore, the velocity of holes in this material would be equal to -0.1V/m/1350cm2/V⋅s = -0.0741 cm/s.
Know more about electric field here:
https://brainly.com/question/8971780
#SPJ11
the cantilevered beam is made of a36 steel and is subjected to the loading shown. determine the displacement at b using the method of superposition. for a36 steel beam, the moment of inertia i
Thus using method of superposition, the total displacement is 0.0276.
A36 steel beam is used Cantilever beam is loaded. The moment of inertia is I. For A36 steel beam, I = 6667 in4 (approx.)As per the method of superposition, the total displacement of the beam at point B is given as follows:δtotal = δP + δWWhere,δP is the displacement of point B due to the point loadδW is the displacement of point B due to the uniformly distributed load.
Considering point load,P = 1500 lb. Distance of the point load from point B = 5 ft. Thus, the moment at point B due to point load can be calculated as follows: MBP = PL = 1500 × 5 = 7500 lb-ft. Similarly, considering uniformly distributed load,W = 200 lb/ft. Thus, the moment at point B due to uniformly distributed load can be calculated as follows:Mbw = (wL2)/12Where,L is the length of the beam= 10 ft
Therefore, Mbw = (200 × 102)/12 = 1667 lb-ft (approx.)Thus, total moment at point B,M = MBP + MBW= 7500 + 1667= 9167 lb-ft. Thus, using the formula for deflection of cantilever beam,δP = (PbL2)/(2EI) = (1500 × 52)/(2 × 29 × 106 × 6667) = 0.0026 inδW = (WbL3)/(3EI) = (200 × 5103)/(3 × 29 × 106 × 6667) = 0.024 in
Therefore, the displacement at point B is 0.0276 in.
To know more about superposition, refer here:
https://brainly.com/question/12493909#
#SPJ11
A dog can hear sounds in the range from 15
to 50,000 Hz.
What wavelength corresponds to the lower
cut-off point of the sounds at 20◦C where the
sound speed is 344 m/s?
Answer in units of m.
Explanation:
Speed of sound is 344
The frequency corresponding to the lower cut-off point is the lowest frequency which his 15Hz
F=15Hz
The relationship between the wavelength, speed and frequency is given as
v=fλ
Then,
λ=v/f
λ=v/f
λ=344/15
λ=22.93m
What is the function of the organelle depicted in the photo?
Answer:
It's a golgi body
Explanation:
It controls the transport system of the cell
What goes in and out the cel
two 4.0cm*4.0cm metal plates are separated by a 0.20-mm-thick piece of teflon. a. what is the capacitance? b. what is the maximum potential difference between the plates?
The capacitance of two metal plates separated by a 0.20-mm-thick is approximately 0.25 pF and the maximum potential difference between the plates is 8.4 kV.
a. The capacitance of two metal plates separated by a 0.20-mm-thick piece of Teflon is approximately 0.25 pF (picofarad).
b. The maximum potential difference between the two metal plates is determined by the permittivity of the dielectric material, which in this case is Teflon.
The permittivity of Teflon is about 2.1 and the capacitance of the plates is 0.25 pF, so the maximum potential difference between the plates can be calculated using the equation:
Vmax = (permittivity * Capacitance) / Area.
Therefore, the maximum potential difference between the plates is 8.4 kV.
For more such questions on capacitance , Visit:
https://brainly.com/question/13578522
#SPJ11
2. according to our equations, what should be the relationship between the total current and the currents passing through each resistor? does your data show this relationship
According to Ohm's Law, the relationship between the total current and the currents passing through each resistor is that the total current is equal to the sum of the currents passing through each resistor.
What is Ohm's Law?This can be represented mathematically as I total = I₁ + I₂ + I₃ + ... where I total is the total current and I₁, I₂, I₃, etc. are the currents passing through each resistor.
This relationship is consistent with Kirchhoff's Current Law, which states that the sum of the currents entering and leaving a junction in a circuit must be equal to zero. Therefore, the current flowing through each resistor must add up to the total current in the circuit. Yes, this relationship is observed in data obtained from circuits.
To know more about Ohm's Law?
https://brainly.com/question/1247379
#SPJ11
a coil is placed in a changing magnetic field and an emf is induced. what happens to the induced emf if the rate of change of magnetic field quadruples?
The induced EMF increases to four times its initial value if the rate of change of the magnetic field quadruples.
Faraday's law of electromagnetic induction specifies that an emf (electromotive force) is induced in a closed conductor or coil whenever there is a change in magnetic flux associated with it.
EMF = − d(ΦB) /dt
ΦB = BAcosθ
This equation suggests that emf is proportional to the rate at which magnetic flux ΦB is changing with respect to time. As a result, if the rate of change of the magnetic field quadruples, the induced EMF increases to four times its initial value.
Learn more about Faraday's law at https://brainly.com/question/1640558
#SPJ11
isaac's body plunges to a depth of 2.5m below the water surface before stopping. determine the average force of water resistance experienced by his body
Isaac encountered a water resistance force of 24,525 N on average as he dived to a depth of 2.5m beneath the water's surface.
Isaac's body experienced an average force of water resistance due to the water surrounding it. This force is determined by the volume and density of the water, as well as the acceleration of his body while it is moving.
First, we need to calculate the volume of the displaced water. We can use the formula:
V = Ah
where A is the surface area of the object and h is the depth to which it sinks. Since we don't have the surface area of Isaac's body, we can assume it to be 1 square meter for simplicity.
V = 1 * 2.5 = 2.5 cubic meters
To calculate the average force of water resistance experienced by his body, we can use the equation
Force = Volume x Density x Acceleration.
Using this equation, we can calculate the force of water resistance as follows:
Force = 2.5m^3 x 1000kg/m^3 x 9.81m/s^2
Force = 24,525 N.
Therefore, Isaac experienced an average force of water resistance of 24,525 N while his body was plunging to a depth of 2.5m below the water's surface.
To know more about the "average force of water resistance": https://brainly.com/question/20629953
#SPJ11
Please help. Due at Midnight!
The magnitude and direction of the net force on the center charge is 3.929 x 10⁻⁴ N.
What is unit of charge?The unit of charge is the Coulomb (C). It is named after French physicist Charles-Augustin de Coulomb and is defined as the amount of electric charge that flows through a circuit when a current of one ampere flows for one second. One Coulomb is also equivalent to the charge on approximately 6.24 x 10¹⁸ electrons. The Coulomb is one of the seven base SI units (International System of Units) and is used to measure electric charge in physics and engineering.
So, the magnitude of the net force on the center charge is 3.929 x 10⁻⁴ N. Since F12 is directed towards the left, and F23 is directed towards the right, the net force is also directed towards the left. Therefore, the direction of the net force on the center charge is to the left.
According to Coulomb's law to calculate the force exerted by each of the other charges on the center charge, and then add them vectorially.
Let's call the left charge Q1, the center charge Q2, and the right charge Q3.
The force exerted on Q2 by Q1 is given by:
F₁₂ = k * |Q1| * |Q2| / r₁₂²
where k is Coulomb's constant, |Q1| and |Q2| are the magnitudes of the charges, and r₁₂ is the distance between them. Since Q1 is positive and Q2 is negative, the force F₁₂ is attractive and directed towards Q1. Because the distance between them is 2m, we can say:
F₁₂ = 9 x 10⁹ Nm²/C² * |52 x 10⁻⁶ C| * |3.10 x 10⁻⁶ C| / (2m)²
= 3.468 x 10⁻⁴ N (attractive)
The force exerted on Q2 by Q3 is given by:
F₂₃ = k * |Q2| * |Q3| / r₂₃²
where |Q3| is positive, and |Q2| is negative, so the force F23 is repulsive and directed away from Q3. The distance between them is also 2m, so:
F₂₃ = 9 x 10⁹ Nm²/C² * |3.10 x 10⁻⁶ C| * |68 x 10⁻⁶ C| / (2m)²
= 5.383 x 10⁻⁵ N (repulsive)
To find the net force on Q2, we need to add these two forces vectorially. Since they act along the same line, we can simply subtract their magnitudes:
Fnet = |F₁₂| - |F₂₃|
= 3.468 x 10⁻⁴ N - 5.383 x 10⁻⁵N
= 3.929 x 10⁻⁴ N.
To know more about Coulomb's law, visit:
https://brainly.com/question/9261306
#SPJ1
magnus has reached the finals of a strength competition. in the first round, he has to pull a city bus as far as he can. one end of a rope is attached to the bus and the other is tied around magnus's waist. if a force gauge placed halfway down the rope reads out a constant 1400 newtons while magnus pulls the bus a distance of 1.55 meters, how much work does the tension force do on magnus? the rope is perfectly horizontal during the pull.
The work done by the tension force on Magnus is 2170 J.
What is work?
Work is the product of the force acting on an object and the distance through which the object moves. In other words, work is accomplished when a force is used to transfer energy to an object, causing the object to move some distance as a result.
The force of 1400 N, Distance of 1.55 meters, and a rope tied around Magnus's waist.
The work done by the tension force on Magnus is the product of the force exerted by the tension force and the distance through which Magnus is moved.
W = Fd
where W = Work done by the tension force on Magnus
F = Force of tension force
= 1400 Nd
= Distance moved by Magnus
= 1.55 m
Substituting these values:
W = 1400 N x 1.55 mW
= 2170 J
Hence, the work done by the tension force on Magnus is 2170 J.
To know more about work:
https://brainly.com/question/29762840
#SPJ11
a point charge q is far from all other charges. at a distance of 2 m from q the electric field is 20n/c. what is the force a charge of 5 coulombs feels
The force a charge of 5 coulombs for a point charge 'q' which is far from all other charges can be calculated by Coulomb's law.
The Coulomb's law states that the force between two point charges is proportional to the product of the charges and inversely proportional to the square of the distance between them:
[tex]F = k * (q_1 * q_2) / r^2[/tex]
where F is the force,
k is Coulomb's constant ([tex]k = 9*10^9[/tex] N m² / C²),
q₁ and q₂ are the charges, and
r is the distance between the charges.
We know that there is only one charge, q, and it is far from all other charges, so we can assume that
q₁ = q and q₂ = 5 C.
We also know that the electric field at a distance of 2 m from q is 20 N/C. The electric field is related to the force per unit charge, so we can use the equation:
[tex]E = F / q_2[/tex]
Therefore To find the force F acting on a charge q₂ at that distance.
Rearranging this equation in terms of F, we get:
[tex]F = E * q_2[/tex]
Substituting the values we have, we get:
F = 20 N/C * 5 C = 100 N
Therefore, a charge of 5 coulombs would feel a force of 100 N due to the point charge q.
To lean more about the 'Coulombs Law':
https://brainly.com/question/506926
#SPJ11
A solid cylinder of mass M = 1.25 kg and radius R = 13.5 cm pivots on a thin fixed frictionless bearing a string wrapped around the cylinder pulls downward with a force of F = 7.259 N
What is the magnitude of the angular acceleration of the cylinder?
86.03259 rad/s^2
Consider that instead of force F, a block with mass 0.74 kg with force = 7.259 N is attached to the cylinder with a mass less string.
What is now the magnitude of the angular acceleration of the cylinder
39.3943 rad/s^2
How far does the mass M travel downward before T equals 0.49S and T equals 0.69 S.
0.62755 m
The cylinder is changed to one with the same mass and radius but a different moment of inertia starting from mass starting from rest. The mass is now moved. The distance of 0.448 mass in the time interval of 0.47 seconds.
Find the Inertia of the new cylinder
The inertia of the new cylinder is 0.0566 kgm². Other answers provided are correct.
How to find inertia?The moment of inertia of the new cylinder can be calculated using the formula:
I = (M × d²) / (4 × Δθ)
Where:
M = mass of the cylinder
d = distance moved by the mass
Δθ = change in angular displacement (in radians)
Substituting the given values:
I = (1.25 × 0.448²) / (4 × 0.47)
I = 0.0566 kgm²
Therefore, the moment of inertia of the new cylinder is 0.0566 kgm².
Find out more on moment of inertia here: https://brainly.com/question/3406242
#SPJ1
Lebohang says that when you use a thick syringe to "drive" a thin syringe, you lose strength but gain distance. What do you think
Lebogang says that when you use a thick syringe to "drive" a thin syringe, you lose strength but gain distance. Jaamiah disagrees this means that there is indeed a mechanical advantage, but a distance disadvantage.
A syringe is a medical device that is used for injecting liquids into or extracting liquids from the body. It typically consists of a cylindrical barrel, a plunger, and a needle. The barrel is usually made of plastic or glass and is marked with volume measurements. The plunger fits inside the barrel and can be pushed or pulled to draw or expel liquid. The needle is attached to the end of the barrel and is used to penetrate the skin or other tissue to inject or extract the liquid.
Syringes are commonly used in medical settings for a variety of purposes, such as administering vaccines, medications, or anesthesia. They can also be used to remove fluid from the body, such as in the case of draining abscesses or collecting blood samples for testing.
To learn more about Syringe visit here:
brainly.com/question/20320556
#SPJ4
Complete Question: -
Lebogang says that when you use a thick syringe to "drive" a thin syringe, you lose strength but gain distance. Jaamiah disagrees. She says that you gain both distance and strength. What do you think, and why do you think so?
in u.s. customary units, air pressure is measured in pounds per square inch. in the metric system, it is measured in pascals, and one pascal is equal to
In the metric system, air pressure is measured in pascals. One pascal is equal to a force of one newton per square meter.
Air pressure can be measured using different units. Pascal is a unit of pressure, defined as one newton per square meter. This unit is named after Blaise Pascal, a French mathematician, physicist, and philosopher who made important contributions to the fields of hydrodynamics and hydrostatics.
In the US customary system, air pressure is measured in pounds per square inch (psi), while in the International System of Units (SI), it is measured in pascals (Pa). The unit psi is used to measure pressure in liquids and gases, and it is defined as the amount of pressure exerted by a force of one pound-force per square inch.
Learn more about pascal unit at https://brainly.com/question/30777634
#SPJ11
a spherical capacitor has vacuum between its conducting shells and a capacitance of 125 pf . the outer shell has inner radius 9.00 cm . what is the outer radius of the inner shell? express your answer with the appropriate units.
For a spherical capacitor with a capacitance of 125 and a vacuum between its conducting shells, the outer radius of the inner shell is around 5.60 cm.
The capacitance of a spherical capacitor is given by:
C = 4πε₀[(r₁r₂)/(r₂-r₁)]
where C is the capacitance, ε₀ is the electric constant (8.85 x [tex]10^{-12}[/tex] F/m), r₁ is the radius of the inner shell, and r₂ is the radius of the outer shell.
In this case, we know that the capacitance C = 125 pF (picoFarads), r₂ = 9.00 cm, and we want to find r₁.
We can rearrange the equation to solve for r₁:
r₁ = (C × r₂)/(4πε₀ + C)
Substituting the values:
r₁ = (125 x [tex]10^{-12}[/tex] F × 0.09 m) / (4π × 8.85 x [tex]10^{-12}[/tex] F/m + 125 x [tex]10^{-12}[/tex] F)
r₁ ≈ 5.60 cm
Therefore, the outer radius of the inner shell is approximately 5.60 cm.
To learn more about the capacitor at
https://brainly.com/question/17176550
#SPJ4
if you hold a 1.85 kg k g package by a light vertical string, what will be the tension in this string when the elevator accelerates as in the previous part?
The tension in the string of a 1.85 kg package held by a light vertical string will depend on the acceleration of the elevator. When the elevator accelerates, the force of acceleration on the package will be equal and opposite to the tension in the string, causing the tension to increase.
The equation for tension in a string is:
Tension = Mass x Acceleration
Therefore, in this case, the tension in the string is equal to 1.85 kg x Acceleration.
If we assume that the acceleration of the elevator is a constant rate, then the tension in the string can be calculated by multiplying the mass of the package by the acceleration of the elevator.
To sum up, the tension in the string of a 1.85 kg package held by a light vertical string will depend on the acceleration of the elevator. If the acceleration of the elevator is a constant rate, then the tension in the string can be calculated by multiplying the mass of the package by the acceleration of the elevator.
For more such questions on Tension.
https://brainly.com/question/13397436#
#SPJ11
you are trying to solve a physics problem and the first thing you try doesnt workyou try another and then another and eventually you figure it out what is this method called
The method of trying different approaches to solve a problem until one works is called trial and error.
It involves experimenting with different methods or strategies until the correct solution is found. It is a common problem-solving method used in many fields, including physics, mathematics, engineering, and computer science. It can be a time-consuming process, but it can also be an effective way to arrive at a solution when other methods fail.
What is trial and error method?
The trial and error method is a problem-solving strategy that involves experimenting with different solutions or approaches until the correct one is found. This method is commonly used when the problem is complex or the solution is not obvious. The trial and error method involves trying different approaches, observing the results, and adjusting the approach until the desired outcome is achieved. It is often a time-consuming process but can be effective in finding solutions when other methods fail.
To know more about trial and error method, visit:
https://brainly.com/question/4123314
#SPJ1
at what angle of deflection makes the magnetic field strngth produced by the coil of the wire equal to the ambient magnetic field
The magnetic field strength created by the wire coil is equivalent to the ambient magnetic field when it is deflected at a right angle.
The magnetic field strength created by the wire coil is equivalent to the ambient magnetic field when it is deflected at a right angle. The Biot-Savart Law, which relates magnetic field strength to the current in a wire and the distance from the wire, applies to a wire coil.
The strength of the magnetic field generated by a current-carrying wire is proportional to the current in the wire and the number of turns per unit length. The magnetic field's intensity is determined by the number of turns in the wire coil, the current in the wire coil, the radius of the coil, and the permeability of free space.
The equation for calculating the magnetic field strength at a point in space around a current-carrying wire is given by the Biot-Savart Law:
B = µ₀I/2πr.
Where µ₀ is the permeability of free space, I is the current, and r is the distance from the wire to the point where the magnetic field strength is to be calculated.
Learn more about Biot-Savart Law at https://brainly.com/question/29564274
#SPJ11